GMC Yukon 2000–2006
Common on this vehicle:Gauge or instrument faultNoiseWarning lightCorrosion or rustLeakReduced brakingAir conditioning or heaterVibration or shudder
There are 2,994 records on the 2000–2006 GMC Yukon (Owner complaint: 1,328, Recall: 35, Manufacturer communication: 1,631). The documents describe 149 known issues; those with the most records under them are Gauges stick or flutter (177), Brake pipe corrosion (157), ABS activation at low speed (63).
Possible causes
All records of the GMC Yukon2,994 records
Instruments and lighting
Brakes
Fuel system
Transmission and driveline
Steering
Body, doors and interior
177106157633153232115111352153 causes not drawn
- Voltmeter fluctuates between 12 and 14 volts (Regulated Voltage Control, normal)4
- CHECK OIL LEVEL message stays on after an oil change or top-off until the engine cools1
- Brake Light3
- Hydro-boost brake assist and power steering share one hydraulic supply (four campaigns)11
- Brake pedal moves or self applies at full steering lock (Hydro-Boost)10
- ABS light with C0265/C0201/U1041 or no communication with brake module (EBCM ground G110)2
- Brake pedal pushrod retainer missing - recall 05V-1031
- Cosmetic brake rotor corrosion: burnish, do not resurface1
- Front right-hand brake pipe contact with body cross sill - recall 00V-3451
- DIC “Reduced Brake Power” message and reduced vacuum boost1
- Service Brake Booster message on a Hydroboost vehicle with DTC C0136 (instrument cluster not SPS programmed)1
- Stability System Disabled / Service Stability message with DTC C0455 (bent terminals at the steering wheel position sensor)1
- Stability System Disabled message and unwanted StabiliTrak activation (tire wear or mismatched tires)1
- Violent steering wheel shake or vibration at road speed (brake booster)1
- ABS lamp with DTC C0265 (EBCM motor relay circuit) after EBCM replacement1
- Buzz at the accelerator pedal on the first acceleration after start (Supplemental Brake Assist self-test, normal)1
- Electronic Brake Control Module15
- Brake Rotor12
- Aftermarket part (not the vehicle as built): Fram G3727 replacement fuel filter connector - recall 06E-0431
- Fuel gauge reads low or drops to empty in Park / Neutral (normal characteristic)1
- Fuel pressure regulator buzz / hum after replacement (check fuel pump feed voltage drop and connector crimps)1
- Fuel Pump15
- Fuel Line9
- Fuel Pump Wiring5
- Fuel Tank4
- 4L80-E / 4L85-E planetary gear whine in first and second gear1
- Service 4WD indicator and DTC B2725 (transfer case shift control switch)1
- Transfer case service light, New Venture Gear transfer case (replace the encoder motor sensor and reprogram the TCCM)1
- Electronic transfer case stops shifting with no DTC (shift abuse lock out mode, normal)1
- Transfer case speed sensor connector locks bend on disconnect (improved connector)1
- 4L60-E / 4L65-E clunk on 2-3 upshift or 3-2 downshift (normal condition)1
- Grind / ratchet noise when shifting into Park in 4LO (characteristic)1
- Transmission15
- Rear Axle5
- Tire scrub noise on low speed turns (steering rod / centerlink installed backwards)1
- RPO DL3 power folding mirror loose, moves or shakes after being folded by hand (cycle it electrically)2
- Door manual lock lever disengages from the door trim panel (lock lever replacement)2
- Driver's seatback moves during braking (recliner replacement)2
- Front floor carpet wet or musty odor (rear door water deflector replacement)2
- Headliner sagging (hook and loop patch detached; reattach with epoxy)2
- Factory trailer hitch receiver bent, broken or weld failure2
- Bench seat (RPO AE7) center console armrest hinges broken (replace the lid, not the console assembly)1
- Rattle from the center of the dash (cowl insulator clip)1
- Center console cupholder and ashtray lid will not close (Denali; latch pulled out of its retainer)1
- Door sags or is hard to open or close (worn or corroded hinge pins and bushings)1
- Snap or popping noise from the front of the vehicle (slot the front crossmember mounting holes)1
- Front seat adjuster switch knob loose or missing (replace only the switch cover)1
- Headliner or roof rattle (roof drain channel)1
- Stains on the rear bumper step pad (treat with Armor-Dillo, do not replace)1
- Broken latch of the rear cupholder in the center console (replace the latch only)1
- Rear door upper hinge welds out of specification (FMVSS 214) - recall 03V-0371
- Second-row rearward folding head restraint pinch points - recall 02V-2531
- Side access door noise (door check link replacement)1
- Double vision or ghost image in the driver's auto dimming outside mirror (normal)1
- Rear Window Glass14
- Liftgate Glass Hinge12
- Seat11
- Power Window10
- Mirror Glass5
- Seat Back5
- Remote keyless entry and front passenger door window, lock, mirror inoperative (reprogram the Passenger Door Module)14
- Passlock theft deterrent: starts then stalls / no-start with security lamp4
- Rear seat audio and/or rear HVAC controls inoperative (replace the RSA, not the console)3
- Trailer brakes applied whenever headlamps or park lamps are on (brake controller jumper harness)3
- Ground Ring Terminal3
- Adjustable pedals do not recall preset positions and/or front heated seats turn off after 30 seconds (brake pedal position switch)2
- CD slow to play, CHECK CD error, CD stuck or clock resets to 12:00 (reprogram the radio, do not replace it)2
- No audio out of the speakers at times (radio reprogram or amplifier replacement)2
- Starter keeps cranking after the key is released (PCM-controlled automatic crank, normal)2
- Generator whine in the audio system (new ground for radio and amplifier)1
- Intermittent battery drain from a sticking A/C compressor relay1
- Intermittent MIL, service lamps/messages or DTCs from connector fretting corrosion1
- Positive battery cable contact with steering shaft universal joint (Denali) - Transport Canada 20010921
- Intermittent stall, misfire or crank no start (Ignition 1 feed wire broken near C148/C149)1
- Memory seat recalls to a more-forward position than set (memory seat module software)1
- Navigation radio returned from the Electronic Service Center: no navigation and CD ERROR message1
- No crank with a blown Ign A fuse (circuit 142 pinched at the steering column support bracket)1
- Poor radio reception from a loose radio antenna mast1
- Radio shows a disc error when a media disc is inserted (unsupported disc format or damaged disc)1
- No audio and no radio display, or radio clock resets (2004; radio set-up with the Tech 2)1
- Red radio theft LED does not flash (manufacturer's counter not reset at assembly)1
- Rear wiper jumps when the fog lamps are turned on (auxiliary ground to rear washer pump)1
- Reduced Engine Power from throttle body connector crimp, broken wire or grounds1
- Seat heater or memory power seat inoperative (memory seat control module)1
- Conversion equipment (not the vehicle as built): Southern Comfort running board courtesy lights overheating - recall 03V-0941
- Turn signal flashes fast (export flasher relay installed)1
- DRLs or auto headlamps will not disable with the headlamp switch (Canada, RPO Z49; normal)1
- Hum or fan noise from the navigation radio (internal cooling fan, normal)1
- Radio volume lower at the same setting after reprogramming or replacement (new audio calibration, normal)1
- Replacement headlamp switch has no LED indicators and sets DTC B0951 (2003, normal)1
- Battery5
- Wiring4
- Exhaust pop or ping noise (replace the heat shield, not the exhaust system)13
- P0420 / P0430 on a new or just-replaced catalytic converter (break-in not completed)5
- Purge Solenoid1
- Oxygen Sensor2
- Intake manifold gasket leak (cold idle misfire, lean codes)9
- Single-cylinder misfire (P0300-P0308) and/or chirp, squeak or tick at camshaft speed: worn cam lobe / lifter, valve or valve spring7
- Increased accelerator pedal effort / throttle body sticks (clean and adjust, do not replace)5
- Castech cylinder head porosity crack (gradual coolant loss)5
- DTCs P2108, P1516 and U0107 (do not replace the TAC module)4
- Oil leak after cold start from frozen PCV system (rear main seal)4
- Lean hesitation, sag or stumble at -6 to +20°C coolant temperature (PCM reprogram)2
- Accessory drive belt whine (power steering pump pulley repositioned)1
- Crankshaft position sensor may work intermittently or fail (8.1L V8) - recall 07V-5211
- Engine vibration or noise at idle felt in the steering wheel or seat (reprogram the PCM)1
- Higher than expected engine oil consumption (PCV valve replacement)1
- P0300 after engine repairs: injector connectors crossed (cylinders 5-7 / 6-8)1
- Rear bank knock sensor corrosion from water intrusion (P0332)1
- Slight roughness at idle with no DTCs (possible characteristic)1
- Throttle body carbon build-up: idle surge, reduced engine power, throttle DTCs (high mileage)1
- HVAC blower motor resistor module / connector overheating4
- Engine compartment noise with A/C on and A/C inoperative (auxiliary rear A/C: suction hose and compressor)3
- Rear HVAC ticking noise, no rear temperature or mode control, DTC B0434 / B3764 (revised auxiliary HVAC control module)2
- No passenger compartment air filter (not available from the 2003 model year; normal)2
- Climate Control Module2
- A/C blows warm at extended idle (6.0L: auxiliary electric cooling fan)1
- Blower motor inoperative after blower control module replacement (auto HVAC)1
- HVAC actuator clicking / ticking noises (recalibrate the HVAC control module, do not replace actuators)1
- Loss of HVAC mode or temperature control (wiring harness rerouted)1
- Passenger side colder or warmer than the driver's side (HVAC case to cowl seal)1
- Insufficient heat from the rear heater in extreme cold (tee coupling replacement)1
- Seat Heater6
- Air Conditioning Compressor3
- Encoder Motor2
- OnStar System6
- OnStar cannot configure the vehicle (118 error) after the 15-08-44-001 upgrade2
- Some OnStar features no longer work (2G cellular sunset; the module is not broken)2
- No response when the OnStar button is pressed (DTC B2476): button assembly test values1
- Red OnStar LED and DTC B2455 after Canada upgrade bulletin 15-08-44-001 (audio and microphone drain wires shorted)1
- Digital Radio Receiver1
- CD Player3
- Wheel4
- Vehicle body tilt or lean left / right (torsion bar front suspension)3
- Aluminum Wheel Bead Seat2
- Aftermarket part (not the vehicle as built): Federal-Mogul National / Carquest replacement wheel hub assembly retention nut - recall 07E-1061
- Grease seen at front hub bearing seals (normal purge, do not replace)1
- Creak or squeak noise from the rear lower control arm bushings (do not replace the propshaft)1
- Upper control arm bracket alignment (dowel) pin missing at front end alignment1
- Wheel Bearing3
- Tire recall (not the vehicle as built): Firestone Wilderness LE tread separation - recall 01T-0014
- Tire and loading information label lists inaccurate vehicle capacity weight (FMVSS 110) - recall 05V-5521
- Bolt4
- Seat Belt Buckle3
- Air bag sensing diagnostic module (SDM) anomaly - recall 02V-1782
- Second row seat belt retractor does not lock automatically for a child restraint2
- Air bag lamp on with DTC B0092 (passenger presence system sensor harness)1
- AIR BAG indicator on with side impact module DTCs (connector CPA replacement)1
- 2nd/3rd row outboard seat belt retractor internal crack - recall 01V-1591
- 2nd row center seat belt routing (lap belt fit) - recall 05V-1631
- SIR lamp on and inside mirror temperature/compass display inoperative (open air bag fuse, circuit 1139 shorted to ground)1
- Air bag (SIR) lamp on with DTC B1001 after BCM or SDM replacement1
- Coolant leak at the rear of the vehicle (auxiliary heater hose quick connector)1
The documents say what to doOnly records name itThe size of a node, the width of a link and the numbers are records matching this search, not likelihoods.
FaultCrate・GMC Yukon 2000–2006
Candidate cause (the documents say what to do)
Autoride (Z55) Service Ride Control / Service Suspension System message
On 2009 or earlier vehicles a Service Suspension System message may appear and the rear ride height may be incorrect.
The Electronic Suspension Control module will have DTC C0696 or C0711 set.
How to tell
C0580C0696C0711Service Ride Control / suspension message
What to do
- The compressor assembly may need to be removed to see whether the wiring is pinched between the compressor and the frame.
- The module checks level-system pressure at start-up and runs the compressor to add air to the shocks if it is below 10 psi (69 kPa).
- Repair the damaged or shorted circuits and reposition the wiring so it is not damaged again when the compressor is installed.
- The sensor is not serviced separately; install a complete air filter, dryer and sensor assembly.
- For a Service Ride Control message with DTC C0580, replace the right front shock absorber solenoid connector and install new A/C suction and auxiliary evaporator hoses.
- The jumper harness is included with the complete air filter, dryer, and sensor assembly PN 22964558; vehicles built in May, 2012 and later do not require the jumper harness and use PN 22941807.
Caution: Do not replace the complete air compressor assembly for this concern.
Part numbers printed in the document
22964558Filter Assembly, Auto Level Control Air CompressorLook up at RockAuto (aftermarket candidates) ↗Search the web ↗
Discontinued (no successor stated)(replaces 20982305 / 22197161)as stated by GMPartsGiant (checked 2026-10-06) ↗
22941807Filter Assembly, Auto Level Control Air CompressorLook up at RockAuto (aftermarket candidates) ↗Search the web ↗
Discontinued (no successor stated)as stated by GMPartsGiant (checked 2026-10-06) ↗
22197160Look up at RockAuto (aftermarket candidates) ↗Search the web ↗
The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.
In the records
- Air Compressor: repaired 1
- Air Conditioning Suction Hose: replaced 1
- Air Filter Dryer and Sensor Assembly: replaced 1
See the evidence (1 technical documents, 4 records)
Passages of the technical documents
2001-2013 GMC Yukon, Yukon XL LD, Yukon Denali, Yukon Denali XL With RPO Z55 or Z95
General Motors (filed with NHTSA as SB-10052488) 2013-06-01
Some customers of 2009 or prior vehicles, may comment of a Service Suspension System message on the DIC and the rear suspension ride height is incorrect.
General Motors (filed with NHTSA as SB-10052488) 2013-06-01
When checking for DTCs the Electronic Suspension Control (ESC) module will have DTC C0696 or C0711 set.
General Motors (filed with NHTSA as SB-10052488) 2013-06-01
This concern could be caused by the wiring to the automatic level control (ALC) pressure sensor being shorted to ground, as shown below.
General Motors (filed with NHTSA as SB-10052488) 2013-06-01
A cause or a result a complaint states is the owner’s view or what a dealer told them, not an established fact.
Put together by FaultCrate from public records and technical documents. The cause and the repair are for the workshop to decide with the vehicle in front of it. Counts are records, not failure rates.