Skip to content
FaultCrate
日本語

This is an open preview: every record can be read without an account.

GMC Yukon XL 2000–2006

GMC Yukon XLModel years 2000–2006

Change vehicle →
Clear the search
2 conditions added

Common on this vehicle:Warning lightLeakNoiseMisfire or rough idleCorrosion or rustStalls or shuts offVibration or shudderDoes not start

Record by record

3 records state a cause or a remedy. Each record is shown as short labels in the order fault → finding the cause → correction. Press a label to narrow to the records that state it.

Symptom

Component named as the cause

A ribbon is as wide as the records that state both of its ends (only the commonest are drawn). A record that names several symptoms or components runs through each. Orange is records that say the fault came back or was not fixed. Results come from owners’ reports only; one that does not say is “result not stated”. None of this is a likelihood of a cause or a rate at which work succeeds.

Read the records one by one (3)

STRUCTURE2

  1. Owner complaint2002 GMC YUKON XL ・ 2010-09-19

    Rear tailgate glass hinge failure and improper closure

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      Not stated

    Read the sentences of the record
    Fault
    REAR GLASS DOES NOT CLOSE PROPERLY AND IS AT RISK TO DETACH FROM VEHICLE.

  2. Owner complaint2002 GMC YUKON XL 1500 ・ 2008-11-17

    Liftgate glass detached while driving on highway

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      Not stated

VISIBILITY1

  1. Manufacturer communication2001–2006 GMC YUKON XL ・ 2017-12-22

    Rear Window Defroster Contact or Tabs Service Information

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      Repair

      1. On 2007-2014 Tahoe, Suburban, Yukon and Escalade with moveable glass always replace the defroster tab (GM P/N 25916031) and the power connector (P/N 12034110); on all other vehicles reconnect the original defroster tab.
      2. Remove the rear defroster power connector and crimp a new one to the feed wire; the proper connector, P/N 12034110, is in the Packard Electrical Assortment, Tray 18, Position 5.
      3. Prepare the surface of the used defroster tab and the defroster buss bar with fine grain (500 grit) sandpaper or Emery cloth.
      4. Wipe the prepared contact area with Kent Automotive Acrysol (or equivalent) to remove residual oil or dirt.
      5. Heat the new connector on the buss bar surface to be soldered, holding the connector and defroster tab in place with long nose pliers.

      Part numbers printed in the document

      The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

      Parts

      • Silver solder: Radio Shack (The Source in Canada) 64-013, 0.022" diameter.
      • Solvent: P20005 Kent Automotive Acrysol Solvent (32 fl oz) 946 ml.

      Caution

      • Let the glass warm to the temperature inside the building; soldering creates a hot spot in the glass, so do not solder on cold glass.
      • Heating the glass excessively, or repeatedly without time to cool, may break the glass.
      • A silver-bearing solder must be used; do not attempt the repair with conventional tin/lead alloy solders.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Covers 2000-2015 GM passenger cars and trucks, excluding the 2015 Chevrolet Tahoe, Suburban, GMC Yukon and Cadillac Escalade.
    • Applies to：Vehicles must have the electric rear window defroster (RPO C49).
    • Repair：On 2007-2014 Tahoe, Suburban, Yukon and Escalade with moveable glass always replace the defroster tab (GM P/N 25916031) and the power connector (P/N 12034110); on all other vehicles reconnect the original defroster tab.
    • Caution：Let the glass warm to the temperature inside the building; soldering creates a hot spot in the glass, so do not solder on cold glass.
    • Caution：Heating the glass excessively, or repeatedly without time to cool, may break the glass.
    • Caution：A silver-bearing solder must be used; do not attempt the repair with conventional tin/lead alloy solders.
    • Repair：Remove the rear defroster power connector and crimp a new one to the feed wire; the proper connector, P/N 12034110, is in the Packard Electrical Assortment, Tray 18, Position 5.
    • Repair：Prepare the surface of the used defroster tab and the defroster buss bar with fine grain (500 grit) sandpaper or Emery cloth.
    • Repair：Wipe the prepared contact area with Kent Automotive Acrysol (or equivalent) to remove residual oil or dirt.
    • Repair：Heat the new connector on the buss bar surface to be soldered, holding the connector and defroster tab in place with long nose pliers.
    • Parts：Silver solder: Radio Shack (The Source in Canada) 64-013, 0.022" diameter.
    • Parts：Solvent: P20005 Kent Automotive Acrysol Solvent (32 fl oz) 946 ml.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This informational bulletin provide information for the technicians to repair the rear window defroster contact or tabs.

1 owner complaints have no classified sentences yet, so their causes and repairs are not picked out. Their text is in the list of records.