Skip to content
FaultCrate
日本語

This is an open preview: every record can be read without an account.

GMC Yukon XL 2000–2006

GMC Yukon XLModel years 2000–2006

Change vehicle →
Clear the search
2 conditions added

The vehicle (where a record says)

A record is under an engine, a drive or a series only where it says so: the characters of the vehicle identification number filed with a complaint, its text, or what its document says it applies to. A record that does not say is kept as "not stated". The filed numbers and the documents do not tell 4WD from AWD.

Common on this vehicle:Warning lightSeat belt

Record by record

4 records state a cause or a remedy. Each record is shown as short labels in the order fault → finding the cause → correction. Press a label to narrow to the records that state it.

Symptom

Component named as the cause

Work done

A ribbon is as wide as the records that state both of its ends (only the commonest are drawn). A record that names several symptoms or components runs through each. Orange is records that say the fault came back or was not fixed. Results come from owners’ reports only; one that does not say is “result not stated”. None of this is a likelihood of a cause or a rate at which work succeeds.

Read the records one by one (4)

SEAT BELTS3

  1. Manufacturer communication2005–2006 GMC YUKON XL ・ 2018-04-23

    Technical Bulletin 05-09-40-002F Notification

    1. 1Fault

      • Overspool lock: if the webbing snaps back to the stowed position rapidly enough, the retractor locks with the belt fully stowed.
      • Vehicle-sensing lock occurs when the vehicle changes speed or direction abruptly: rapid acceleration, rapid deceleration or aggressive cornering.
      • It can also occur with the vehicle static, parked on a large slant, fore-aft or side-to-side.
      • Web-sensing lock: when the webbing reels out at an accelerated rate it goes into lock mode and stays there until tension is released.
      • Pulling the webbing all the way out automatically converts the retractor into a cinch-down mode (ALR), typically used to secure a child seat tightly.

    2. 2Finding the cause

      Possible causes

      • With the webbing fully loaded on the spool the retractor cannot rewind further to release the locking mechanism, so the occupant cannot extract the belt.

    3. 3Correction

      Repair

      1. Pull hard on the locked webbing and then release; the hard pull extracts a small amount of webbing, which permits a small amount of retraction when released.
      2. The ALR mode is cancelled automatically when the belt is unfastened and stowed.

      Caution

      • Do not replace the retractor for this condition before first trying to disengage the locking mechanism as recommended.
      • A belt that the customer says locks intermittently in these conditions is working as designed and functioning properly.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to 2005-2014 GM passenger cars and light duty trucks.
    • Condition：Overspool lock: if the webbing snaps back to the stowed position rapidly enough, the retractor locks with the belt fully stowed.
    • Cause：With the webbing fully loaded on the spool the retractor cannot rewind further to release the locking mechanism, so the occupant cannot extract the belt.
    • Caution：Do not replace the retractor for this condition before first trying to disengage the locking mechanism as recommended.
    • Repair：Pull hard on the locked webbing and then release; the hard pull extracts a small amount of webbing, which permits a small amount of retraction when released.
    • Condition：Vehicle-sensing lock occurs when the vehicle changes speed or direction abruptly: rapid acceleration, rapid deceleration or aggressive cornering.
    • Condition：It can also occur with the vehicle static, parked on a large slant, fore-aft or side-to-side.
    • Caution：A belt that the customer says locks intermittently in these conditions is working as designed and functioning properly.
    • Condition：Web-sensing lock: when the webbing reels out at an accelerated rate it goes into lock mode and stays there until tension is released.
    • Condition：Pulling the webbing all the way out automatically converts the retractor into a cinch-down mode (ALR), typically used to secure a child seat tightly.
    • Repair：The ALR mode is cancelled automatically when the belt is unfastened and stowed.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This technical bulletin provides a revision of 05-09-40-002F to add the 2013-2014 model years.

  2. Manufacturer communication2001–2006 GMC YUKON XL ・ 2017-08-15

    Seat belt buckle operation and warning light issues

    1. 1Fault

      • Seat belt buckles do not operate and/or the seat belt warning light is on; the buckle is hard to latch or unlatch, or the release button sticks.

    2. 2Finding the cause

      Possible causes

      • Sticky beverages spilled onto or into the buckle assembly; debris from food, candy wrappers, paper and coins can also contribute.

      Steps to confirm (in the document’s order)

      • Shine a light on the latch plate insertion area of the buckle and look for debris or foreign objects.

    3. 3Correction

      Repair

      1. If debris is seen, try to vacuum it out, then latch and unlatch the belt; if it works properly, do not replace the buckle assembly.
      2. If not corrected, inspect the buckle for sticky residue; if found, the buckle assembly must be replaced at the customer's expense.

      Caution

      • Never insert anything but the latch plate into the buckle, do not dig anything out with a tool, and never wash out a buckle to remove a spilled liquid because this may damage it.
      • This is not a manufacturing defect and is not covered by the new vehicle warranty.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：2016 and prior GM passenger cars and trucks.
    • Condition：Seat belt buckles do not operate and/or the seat belt warning light is on; the buckle is hard to latch or unlatch, or the release button sticks.
    • Cause：Sticky beverages spilled onto or into the buckle assembly; debris from food, candy wrappers, paper and coins can also contribute.
    • Caution：Never insert anything but the latch plate into the buckle, do not dig anything out with a tool, and never wash out a buckle to remove a spilled liquid because this may damage it.
    • Confirm：Shine a light on the latch plate insertion area of the buckle and look for debris or foreign objects.
    • Repair：If debris is seen, try to vacuum it out, then latch and unlatch the belt; if it works properly, do not replace the buckle assembly.
    • Repair：If not corrected, inspect the buckle for sticky residue; if found, the buckle assembly must be replaced at the customer's expense.
    • Caution：This is not a manufacturing defect and is not covered by the new vehicle warranty.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This informational bulletin provides information to advise dealers about seat belt buckles not operating and/or seat belt warning light illumination, as well as difficulty latching and unlatching the buckle or the buckle release button sticking.

  3. Manufacturer communication2005–2006 GMC YUKON XL 2500 ・ 2011-05-11

    Safety Belt Locking Function Service Bulletin

    1. 1Fault

      Not stated

    2. 2Finding the cause

      Not stated

    3. 3Correction

      GM: SERVICE BULLETIN EXPLAINING WHEN THE SAFETY BELTS ARE SUPPOSED TO LOCK. *RM UPDATED 12/6/11. *PE

    Read the sentences of the record
    Remedy
    GM: SERVICE BULLETIN EXPLAINING WHEN THE SAFETY BELTS ARE SUPPOSED TO LOCK. *RM UPDATED 12/6/11. *PE

AIR BAGS1

  1. Manufacturer communication2003–2006 GMC YUKON XL 2500 ・ 2017-08-25

    Electronic Accessory Control System – Coil Harness Centering Service Communication

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      Repair

      • Return all parts with a calendar date from July 29, 2015 to Oct 07, 2016 (Julian date from 15210 to 16280).
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Dorman Products, Inc. is inspecting the NAPA Airbag Clock Spring p/n 665-3499.
    • Repair：Return all parts with a calendar date from July 29, 2015 to Oct 07, 2016 (Julian date from 15210 to 16280).

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    All applicable vehicle applications are without Electronic Accessory Control System option. This communication is to return unsold inventory because some product sold in 2016 may not have coil harness wound in a centered condition as an assembly aid. If installer does not center the rotations of the assembly during replacement process in accordance with applicable AllData service and repair procedure, post-install turning of the steering wheel will trigger the air bag warning light of the vehicle.