Skip to content
FaultCrate

This is an open preview: every record can be read without an account.

GMC Yukon 2000–2006

GMC YukonModel years 2000–2006

Change vehicle →
Clear the search
1 conditions added

The vehicle (where a record says)

A record is under an engine, a drive or a series only where it says so: the characters of the vehicle identification number filed with a complaint, its text, or what its document says it applies to. A record that does not say is kept as "not stated". The filed numbers and the documents do not tell 4WD from AWD.

Common on this vehicle:Warning lightNoiseLeakGauge or instrument faultAir conditioning or heaterVibration or shudderLoss of engine power, no accelerationSeat belt

issuenoneRemove

Possible causes

Noise174 records
Suspension, wheels and tires
Engine
Electrical, wiring and power
Body, doors and interior
Brakes
Transmission and driveline
3Tire: broken, failed1Control Arm: failed1Hub Assembly: worn0Aftermarket part (not the vehicle as built): Federal-Mogul National / Carquest replacement wheel hub assembly retention nut - recall 07E-1062WD only0Creak or squeak noise from the rear lower control arm bushings (do not replace the propshaft)2Serpentine Belt: broken, worn0Accessory drive belt whine (power steering pump pulley repositioned)1500 only0Engine vibration or noise at idle felt in the steering wheel or seat (reprogram the PCM)0Single-cylinder misfire (P0300-P0308) and/or chirp, squeak or tick at camshaft speed: worn cam lobe / lifter, valve or valve spring0Oil pump pickup (screen) O-ring cut: engine tick / lifter noise4.8L, 5.3L, 6.0L only0Rear bank knock sensor corrosion from water intrusion (P0332)4.8L, 5.3L, 6.0L only1Battery: failed1Cigarette Lighter: loose or misadjusted0Generator whine in the audio system (new ground for radio and amplifier)0Hum or fan noise from the navigation radio (internal cooling fan, normal)1Seat: broken0Rattle from the center of the dash (cowl insulator clip)0Snap or popping noise from the front of the vehicle (slot the front crossmember mounting holes)0Headliner or roof rattle (roof drain channel)0Side access door noise (door check link replacement)1Electronic Brake Control Module: failed0Buzz at the accelerator pedal on the first acceleration after start (Supplemental Brake Assist self-test, normal)0Parking brake linings worn out prematurely, parking brake does not hold (PBR single-shoe drum-in-hat)1500 only1Transfer Case Chain: worn04L60-E / 4L65-E clunk on 2-3 upshift or 3-2 downshift (normal condition)04L80-E / 4L85-E planetary gear whine in first and second gear0Grind / ratchet noise when shifting into Park in 4LO (characteristic)
12 causes not drawn
Causes with no correction stated (33)

Causes the records name for which no check or repair is stated, in a technical document or in a record. Press one for the records that name it.

Airbags and seat belts
Airbag Sensor: failed (1)
Electrical, wiring and power
Horn: failed (1)Yaw Sensor: software (1)
Suspension, wheels and tires
Shock Absorber Mount: corroded (1)

The documents say what to doOnly records name itThe size of a node, the width of a link and the numbers are records matching this search, not likelihoods.

Candidate cause (the documents say what to do)

Rear bank knock sensor corrosion from water intrusion (P0332)

Applies to: 4.8L, 5.3L, 6.0L only

Customers may report mild to severe engine ping (spark knock), usually worse during acceleration, and/or an illuminated MIL.

The technician may find DTC P0332 set.

How to tell

P0327P0332Check engine / Service Engine Soon

What to do

  1. If P0327 and P0332 set at the same time, inspect for poor connections at the two-wire knock sensor harness located at the left rear side of the intake manifold near the top, just under the cover.
  2. Check the resistance of the knock sensors including the harness before reinstalling the intake manifold.
  3. Replace the rear bank knock sensor and build an RTV dam around the sensor to divert water away from it.

Caution: Do not form the RTV into a complete circle; leave the rear section open.

What is needed

Parts and materials
  • Rear bank knock sensor
  • RTV (to build a dam around the sensor that diverts water)
Labor time
Not stated
Special tools
Not stated
Scan tool
Not stated

Only what the technical documents state. "Not stated" does not mean not needed.

In the records

No record states work done for this cause.

See the evidence (1 technical documents, 0 records)

Passages of the technical documents

  • The bulletin covers 1999-2002 Chevrolet and GMC C/K pickup and utility models, including Yukon, Yukon XL, Yukon Denali and Yukon Denali XL, with the 4.8L, 5.3L or 6.0L engine.

    1999-2002 Chevrolet and GMC C/K Pickup and Utility Models (Avalanche, Silverado, Sierra, Tahoe, Suburban, Yukon, Yukon XL, Yukon Denali, Yukon Denali XL) with 4.8L, 5.3L or 6.0L Engine

    General Motors (copy hosted by Corvette Action Center)

  • Customers may report mild to severe engine ping (spark knock), usually worse during acceleration, and/or an illuminated MIL.

    Some customers may comment on a mild to severe engine ping (commonly referred to as spark knock), usually worse during acceleration and/or an illuminated MIL.

    General Motors (copy hosted by Corvette Action Center)

  • The technician may find DTC P0332 set.

    Upon investigation, the technician may find DTC P0332 set.

    General Motors (copy hosted by Corvette Action Center)

  • The condition may result from corrosion of the rear bank knock sensor caused by water intrusion into the sensor cavity.

    This condition may be the result of corrosion of the rear bank knock sensor due to water intrusion into the sensor cavity.

    General Motors (copy hosted by Corvette Action Center)

Read every statement and its source →

Records

None among the records that can be opened now.

See all 0 records of this cause →

A cause or a result a complaint states is the owner’s view or what a dealer told them, not an established fact.