Skip to content
FaultCrate
日本語Open preview: everything readable

This is an open preview: every record can be read without an account. The details of the plans are in preparation.

GMC Yukon XL 2000–2006

GMC Yukon XLModel years 2000–2006

Change vehicle →
Clear the search
2 conditions added

Common on this vehicle:Warning lightLeakNoiseMisfire or rough idleStalls or shuts offSmoke or fireVibration or shudderCorrosion or rust

Record by record

51 records state a cause or a remedy. Each record is shown as short labels in the order fault → finding the cause → correction. Press a label to narrow to the records that state it.

Symptom

Component named as the cause

Work done

A ribbon is as wide as the records that state both of its ends (only the commonest are drawn). A record that names several symptoms or components runs through each. Orange is records that say the fault came back or was not fixed. Results come from owners’ reports only; one that does not say is “result not stated”. None of this is a likelihood of a cause or a rate at which work succeeds.

Read the records one by one (17)

Known issuesSingle-cylinder misfire (P0300-P0308) and/or chirp, squeak or tick at camshaft speed: worn cam lobe / lifter, valve or valve spring2

  1. Manufacturer communication2000–2006 GMC YUKON XL ・ 2017-08-15(2 earlier editions of this document folded here)

    Engine Misfire and Service Engine Soon Lamp Information

    1. 1Fault

      • With the SES light on, a P0300-P0308 DTC is found with misfires counting on a single cylinder, which may or may not be felt.
      • The noise may be described as a chirp, squeak, squeal or tick and may increase off of idle.

    2. 2Finding the cause

      Possible causes

      • A worn cam lobe on this engine family generally makes a consistent chirp, squeak, squeal or tick at camshaft speed and/or a misfire with a P0300-P0308 DTC.

      Steps to confirm (in the document’s order)

      1. Press on the rocker arms with a wooden hammer handle while the noise is present; if pressing the valve side of a rocker changes the noise, a lifter and/or cam lobe concern on that cylinder is most likely.
      2. Measure cam lobe lift at the push rod side of the rocker arm; it will differ from the SI specification but should be similar to the other rockers on the same bank.
      3. A bore scope or pen light may help when inspecting the cam lobes through the lifter bores.
      4. A good sign of a sticking valve is that misfires keep counting during an aggressive deceleration with engine braking.
      5. The Cylinder Leakage Test in SI should typically isolate valve leakage by showing excessive leakage past an intake or exhaust valve compared with the others.
      1 more points

    3. 3Correction

      Repair

      1. If a worn cam lobe or lifter roller is found, replace the camshaft and all lifters per SI, plus the plastic lifter guide for the affected lifter (for the 2010 model year, all the plastic lifter guides).
      2. If force is needed to tap the valve off its seat, there is excessive carbon build up, which may be repaired by decarboning the engine.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to 1999-2013 GMC Savana, Sierra and Yukon (with a V8 engine per the model list) (note: the Yukon years run later than the years this service covers).
    • Condition：With the SES light on, a P0300-P0308 DTC is found with misfires counting on a single cylinder, which may or may not be felt.
    • Condition：The noise may be described as a chirp, squeak, squeal or tick and may increase off of idle.
    • Cause：A worn cam lobe on this engine family generally makes a consistent chirp, squeak, squeal or tick at camshaft speed and/or a misfire with a P0300-P0308 DTC.
    • Confirm：Press on the rocker arms with a wooden hammer handle while the noise is present; if pressing the valve side of a rocker changes the noise, a lifter and/or cam lobe concern on that cylinder is most likely.
    • Confirm：Measure cam lobe lift at the push rod side of the rocker arm; it will differ from the SI specification but should be similar to the other rockers on the same bank.
    • Confirm：A bore scope or pen light may help when inspecting the cam lobes through the lifter bores.
    • Repair：If a worn cam lobe or lifter roller is found, replace the camshaft and all lifters per SI, plus the plastic lifter guide for the affected lifter (for the 2010 model year, all the plastic lifter guides).
    • Confirm：A good sign of a sticking valve is that misfires keep counting during an aggressive deceleration with engine braking.
    • Repair：If force is needed to tap the valve off its seat, there is excessive carbon build up, which may be repaired by decarboning the engine.
    • Confirm：The Cylinder Leakage Test in SI should typically isolate valve leakage by showing excessive leakage past an intake or exhaust valve compared with the others.
    • Confirm：The two pieces of a broken valve spring can stay stacked together and be hard to see, so lightly push on different places on the springs with a small hammer handle.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.

  2. Manufacturer communication2000–2006 GMC YUKON XL ・ 2017-08-15

    Service Engine Soon Lamp and Engine Misfire Information

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.

      What the documents say to do

      Single-cylinder misfire (P0300-P0308) and/or chirp, squeak or tick at camshaft speed: worn cam lobe / lifter, valve or valve spring

      Confirm

      • If pressing on the valve side of the rocker changes the noise, a lifter and/or cam lobe concern on that cylinder is most likely.

      Repair

      1. If a worn camshaft lobe or lifter roller is found, follow SI procedures to replace the camshaft and all lifters.
      2. Also replace the plastic lifter guide for the lifter that had the damaged cam lobe and/or lifter roller.

      Caution

      • A damaged cam lobe is easy to overlook when inspecting through the lifter bores; unworn lifter rollers do not mean the cam lobes are okay.
    Read the sentences of the record

    Open the manufacturer’s document (PDF) ↗ What is shown here is NHTSA’s summary; the procedure is in the document itself.

    Remedy
    This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.

Known issuesAftermarket part (not the vehicle as built): Federal-Mogul National / Carquest replacement wheel hub assembly retention nut - recall 07E-1061

  1. Recall2000 GMC YUKON XL ・ —

    Wheel Hub Assembly Bearing Nut Loosening Recall

    1. 1Fault

      • The inboard retention nut that maintains the hub bearing assembly can loosen, resulting in an ABS light indication, noise, and/or wheel separation from the vehicle; wheel separation can result in a vehicle crash.

    2. 2Finding the cause

      Steps to confirm (in the document’s order)

      1. On 2x4 vehicles, raise the vehicle on an approved hoist first; the hub assembly is good if a yellow, green or blue paint mark is seen on the grease cap on the inboard side of the steering knuckle.
      2. If the paint mark is not present, remove the wheel and the brake rotor and clean rust from the hub assembly face to check for the date code stamping.
      3. Defective hub assemblies can be identified by the country of origin on the package together with a recalled date code, by the date code on the package, or by the date code on the hub assembly.
      4. If a round yellow sticker is present on the box label, the part is good.

    3. 3Correction

      Repair

      1. The hub assemblies were manufactured for aftermarket use; owners of these parts should have them removed and replaced as soon as possible.
      2. Federal-Mogul will replace the recalled hub assemblies free of charge.

      Parts

      • The recalled part numbers are 515020, 515021, 515025, 515053, 515054, 515059 and 515060.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：This is an equipment recall by Federal-Mogul of certain wheel hub assemblies sold as replacement parts only.
    • Applies to：The recalled hub assemblies were packaged and sold between January 23, 2006 and December 20, 2007 under the National and CARQUEST Premium (BGS/Blue) brands, in 7 base part numbers.
    • Parts：The recalled part numbers are 515020, 515021, 515025, 515053, 515054, 515059 and 515060.
    • Applies to：The application lists include GMC 1500 Yukon (2WD) and GMC 1500 Yukon XL (2WD), 2001-2006.
    • Applies to：ILJIN manufactured the recalled hub assemblies from December 27, 2005 to November 29, 2007.
    • Condition：The inboard retention nut that maintains the hub bearing assembly can loosen, resulting in an ABS light indication, noise, and/or wheel separation from the vehicle; wheel separation can result in a vehicle crash.
    • Confirm：On 2x4 vehicles, raise the vehicle on an approved hoist first; the hub assembly is good if a yellow, green or blue paint mark is seen on the grease cap on the inboard side of the steering knuckle.
    • Confirm：If the paint mark is not present, remove the wheel and the brake rotor and clean rust from the hub assembly face to check for the date code stamping.
    • Confirm：Defective hub assemblies can be identified by the country of origin on the package together with a recalled date code, by the date code on the package, or by the date code on the hub assembly.
    • Confirm：If a round yellow sticker is present on the box label, the part is good.
    • Repair：The hub assemblies were manufactured for aftermarket use; owners of these parts should have them removed and replaced as soon as possible.
    • Repair：Federal-Mogul will replace the recalled hub assemblies free of charge.
    Cause
    CERTAIN FEDERAL-MOGUL REPLACEMENT WHEEL HUB ASSEMBLIES WITH THE BRAND NAMES: NATIONAL, CARQUEST P/NOS. 515020, 515021, 515025, 515053, 515054, 515059, AND 515060, SHIPPED BETWEEN JANUARY 23, 2006, AND DECEMBER 20, 2007, SOLD FOR LIGHT DUTY AND MEDIUM DUTY TRUCKS. THE INBOARD RETENTION NUT USED TO MAINTAIN HUB BEARING ASSEMBLY CAN LOOSEN RESULTING IN AN ABS LIGHT INDICATION, NOISE, AND/OR WHEEL SEPARATION.
    Remedy
    FEDERAL-MOGUL WILL NOTIFY CUSTOMERS AND WILL REPLACE THE HUB ASSEMBLY FREE OF CHARGE. THE RECALL BEGAN ON FEBRUARY 7, 2008. OWNERS CAN CONTACT FEDERAL-MOGUL TOLL-FREE AT 877-489-6659.
    Consequence
    WHEEL SEPARATION CAN RESULT IN A VEHICLE CRASH.

Known issuesFuel module reservoir assembly: fuel pump wire connectors may overheat - recall 05V-1551

  1. Recall2000 GMC YUKON XL ・ —

    Fuel Module Reservoir Assembly Overheating Recall

    1. 1Fault

      • Some vehicles were built with fuel module reservoir assemblies whose fuel pump wires and/or connectors may overheat under certain operating conditions.
      • If the exposed ignition circuit wire shorts to ground, the fuel pump fuse blows, disabling the fuel pump and causing an engine stall or no-start; if the ignition circuit or ground wire shorts to the fuel level sender card wires, fuel level readings may be inaccurate.
      • If enough heat reaches the pass-through connector, a hole may form in it, which may turn on the Service Engine Soon light during the emission system diagnostics routine; fuel vapor, and in some cases liquid fuel, may leak from the tank through the hole.
      • If enough fuel leaked out and an ignition source were present, a vehicle fire could occur.

    2. 2Finding the cause

      Possible causes

      • Fretting corrosion caused by vibration inside the tank was identified as the cause of high resistance within the fuel pump connector.

    3. 3Correction

      Repair

      1. Dealers remove the fuel tank, remove the fuel module reservoir assembly and install a new service kit, which includes a new pass-through connector and a wiring harness for the fuel pump and fuel sender card.
      2. Start by disconnecting the negative battery cable, then remove and discard the "ECM B" fuse.
      3. In the revised bulletin, the fuel and EVAP pipes are capped with J 41413-300, EVAP Cap/Plug Kit, to prevent fuel system contamination.
      4. Remove the 4 pin Metri Pack 150 electrical connector from the vehicle's body harness.
      5. Connect the new GT280 connector to the vehicle's body harness with the 4 butt splice connectors contained in the kit.
      2 more points

      Parts

      • Part number 15824379, Harness Kit, F/Tnk F/Pmp Mdl Wrg, quantity 1 per vehicle.

      Part numbers printed in the document

      The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

      Caution

      • Do not handle the fuel sender assembly by the fuel pipes; the leverage could damage the joints.
      • Always replace the fuel sender gasket when reinstalling the fuel sender assembly, to reduce the risk of fire and injury from a fuel leak.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：The recall covers certain 2000-2001 Chevrolet 1500 Series Suburban and GMC 1500 Series Yukon XL vehicles built within the listed VIN breakpoints.
    • Condition：Some vehicles were built with fuel module reservoir assemblies whose fuel pump wires and/or connectors may overheat under certain operating conditions.
    • Condition：If the exposed ignition circuit wire shorts to ground, the fuel pump fuse blows, disabling the fuel pump and causing an engine stall or no-start; if the ignition circuit or ground wire shorts to the fuel level sender card wires, fuel level readings may be inaccurate.
    • Condition：If enough heat reaches the pass-through connector, a hole may form in it, which may turn on the Service Engine Soon light during the emission system diagnostics routine; fuel vapor, and in some cases liquid fuel, may leak from the tank through the hole.
    • Condition：If enough fuel leaked out and an ignition source were present, a vehicle fire could occur.
    • Cause：Fretting corrosion caused by vibration inside the tank was identified as the cause of high resistance within the fuel pump connector.
    • Repair：Dealers remove the fuel tank, remove the fuel module reservoir assembly and install a new service kit, which includes a new pass-through connector and a wiring harness for the fuel pump and fuel sender card.
    • Parts：Part number 15824379, Harness Kit, F/Tnk F/Pmp Mdl Wrg, quantity 1 per vehicle.
    • Repair：Start by disconnecting the negative battery cable, then remove and discard the "ECM B" fuse.
    • Repair：In the revised bulletin, the fuel and EVAP pipes are capped with J 41413-300, EVAP Cap/Plug Kit, to prevent fuel system contamination.
    • Caution：Do not handle the fuel sender assembly by the fuel pipes; the leverage could damage the joints.
    • Caution：Always replace the fuel sender gasket when reinstalling the fuel sender assembly, to reduce the risk of fire and injury from a fuel leak.
    • Repair：Remove the 4 pin Metri Pack 150 electrical connector from the vehicle's body harness.
    • Repair：Connect the new GT280 connector to the vehicle's body harness with the 4 butt splice connectors contained in the kit.
    • Repair：Install the fuel tank strap attaching bolts and tighten them to 40 N·m (30 lb ft).
    • Repair：Install the new fuel pump fuse contained in the kit into the vehicle's electrical center (ECM B).
    Cause
    CERTAIN TRUCKS AND SPORT UTILITY VEHICLES WERE BUILT WITH FUEL MODULE RESERVOIR ASSEMBLIES THAT CONTAIN FUEL PUMP WIRES CONNECTORS MAY OVERHEAT UNDER CERTAIN OPERATING CONDITIONS.
    Remedy
    DEALERS WILL REMOVE THE FUEL TANK, AND REMOVE THE MODULE RESERVOIR ASSEMBLIES FROM THE TANK, AND INSTALL A NEW SERVICE KIT FREE OF CHARGE. AN INTERIM LETTER TO OWNERS WAS MAILED ON MAY 25, 2005. THE OWNERS WERE RE-NOTIFIED ON OCTOBER 19, 2005, SINCE PARTS ARE NOW AVAILABE. OWNERS MAY CONTACT CHEVROLET AT 1-800-630-2438 AND GMC AT 1-866-996-9463.
    Consequence
    IF THE IGNITION CIRCUIT WIRE IS EXPOSED, THE FUEL PUMP FUSE WILL BLOW, DISABLING THE FUEL PUMP AND CAUSING AN ENGINE STALL OR NO-START CONDITION. IF SUFFICIENT HEAT IS CONDUCTED TO THE PASS-THROUGH CONNECTOR, A HOLE IN THE CONNECTOR MAY RESULT, WHICH MAY CAUSE A 'SERVICE ENGINE SOON' LIGHT TO BE ILLUMINATED DURING THE EMISSION SYSTEM DIAGNOSTIC ROUTINE. FUEL VAPOR AND IN SOME CASES LIQUID FUEL MAY LEAK OUT OF THE FUEL TANK THROUGH THE HOLE IN THE CONNECTOR BODY. FUEL LEAKAGE, IN THE PRESENCE OF AN IGNITION SOURCE, COULD RESULT IN A FIRE. ALSO IF THE IGNITION CIRCUIT OR GROUND WIRE IS EXPOSED AND SHORTS TO THE FUEL LEVEL SENDER CARD WIRES, INACCURATE FUEL LEVEL READINGS MAY RESULT.

Known issuesP0300 after engine repairs: injector connectors crossed (cylinders 5-7 / 6-8)1

  1. Manufacturer communication2000–2006 GMC YUKON XL ・ 2017-08-15

    P0300 DTC After Engine Repairs – Injector Connector Verification

    1. 1Fault

      • DTC P0300 sets after engine repairs.
      • The engine misfire may not be detected and may happen during deceleration.

    2. 2Finding the cause

      Possible causes

      • The injector connectors for cylinders 5-7 and 6-8 can be crossed, which causes an engine misfire.

      Steps to confirm (in the document’s order)

      • If crossed injector connectors are a possible cause, use the applicable SI document to validate the injector connector routing.

    3. 3Correction

      Repair

      • Correct the injector connector routing and evaluate for the concern.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：The model list includes the 1999-2013 GMC Savana, Sierra and Yukon.
    • Applies to：The listed models are covered when they have a V8 engine.
    • Condition：DTC P0300 sets after engine repairs.
    • Cause：The injector connectors for cylinders 5-7 and 6-8 can be crossed, which causes an engine misfire.
    • Condition：The engine misfire may not be detected and may happen during deceleration.
    • Confirm：If crossed injector connectors are a possible cause, use the applicable SI document to validate the injector connector routing.
    • Repair：Correct the injector connector routing and evaluate for the concern.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This Preliminary Information communication provides information to the technician about vehicles that are setting Diagnostic Trouble Code P0300 after engine repairs. Technician will need to ensure that injector connectors for cylinder 5-7 and 6-8 are not crossed.

ENGINE AND ENGINE COOLING5

  1. Manufacturer communication2000–2006 GMC YUKON XL DENALI ・ 2023-01-06(2 earlier editions of this document folded here)

    EVAP Leak Diagnostic Service Bulletin (DTCs P0442/P0455)

    1. 1Fault

      • The MIL is illuminated, and DTC P0442 (EVAP small leak detected) and/or P0455 (EVAP large leak detected) may be set in the ECM.

    2. 2Finding the cause

      Possible causes

      • P0455 sets because of a large leak or a purge blockage: an unseated tube connection, a damaged tube, a canister vent valve stuck open, or a purge valve stuck closed.
      • P0442 sets because of a small leak, which can come from a purge valve stuck open or a canister vent valve stuck open.

      Steps to confirm (in the document’s order)

      1. Inspect every purge connection for proper installation, and look along the lines for damage or wear; if damage is seen, confirm it with the smoke test.
      2. Some leaks show only under pressure and some only under vacuum, so check both ways; cycling the purge and vent solenoids with GDS2 while inspecting may show a sticking valve.
      3. Critical connections to check include: purge tube to purge valve (at the intake manifold), purge tube to chassis EVAP line (rear of the engine, near the transmission), chassis EVAP line to canister, and fuel tank load line to canister.
      4. Also check the vent valve line at the vent valve, the fuel tank load line jumper connection near the fuel tank, and that the fuel tank cap is closed properly.
      5. If all connections are good, check the vent valve for a stuck-open position; if the vent valve works correctly, go on to the purge valve.
      1 more points

    3. 3Correction

      Parts

      • No parts are required for this repair.

      Caution

      • For diagnostic instructions, DTC information and required tools, always follow the service information document for the vehicle and DTC being worked on.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：This bulletin only applies to vehicles with gasoline engines.
    • Condition：The MIL is illuminated, and DTC P0442 (EVAP small leak detected) and/or P0455 (EVAP large leak detected) may be set in the ECM.
    • Cause：P0455 sets because of a large leak or a purge blockage: an unseated tube connection, a damaged tube, a canister vent valve stuck open, or a purge valve stuck closed.
    • Cause：P0442 sets because of a small leak, which can come from a purge valve stuck open or a canister vent valve stuck open.
    • Confirm：Inspect every purge connection for proper installation, and look along the lines for damage or wear; if damage is seen, confirm it with the smoke test.
    • Confirm：Some leaks show only under pressure and some only under vacuum, so check both ways; cycling the purge and vent solenoids with GDS2 while inspecting may show a sticking valve.
    • Confirm：Critical connections to check include: purge tube to purge valve (at the intake manifold), purge tube to chassis EVAP line (rear of the engine, near the transmission), chassis EVAP line to canister, and fuel tank load line to canister.
    • Confirm：Also check the vent valve line at the vent valve, the fuel tank load line jumper connection near the fuel tank, and that the fuel tank cap is closed properly.
    • Confirm：If all connections are good, check the vent valve for a stuck-open position; if the vent valve works correctly, go on to the purge valve.
    • Confirm：Work in this order: EVAP lines properly installed and fully seated; damage on the EVAP lines; vent valve malfunction; purge valve malfunction.
    • Parts：No parts are required for this repair.
    • Caution：For diagnostic instructions, DTC information and required tools, always follow the service information document for the vehicle and DTC being worked on.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.

  2. Manufacturer communication2000–2006 GMC YUKON XL DENALI ・ 2022-09-07

    MIL Illuminated with Fuel Trim and Oxygen Sensor Codes

    1. 1Fault

      • Customers may comment that the MIL is illuminated.
      • Initial diagnosis may show fuel trim and O2 sensor related codes including P0101, P0137, P0138, P0140, P0141, P0157, P0158, P0160 and P0161.
      • The listed codes also include P0171, P0174, P0420, P0430, P1174 and P1175.

    2. 2Finding the cause

      Possible causes

      • These methods find small leaks around the O2 sensor embossments and slight cracks in an intake plenum or gasket.

      Steps to confirm (in the document’s order)

      1. If normal SI diagnostics do not lead to a resolution and an intake vacuum leak or exhaust leak is suspected, use the GE-52250 Variable Pressure Leak Detector (preferred), the J-41416 ultrasonic leak tester, or possibly soapy water with low pressure air into the tailpipe to find the leak.
      2. For an intake leak, introduce the smoke into the brake booster hose or the oil dipstick tube; soapy water can be sprayed near the gasket, seams and all vacuum nipples.
      3. For an exhaust leak, put the hose with smoke or air into the tailpipe sealed with shop towels, then spray soapy water around seals, seams and bosses.

    3. 3Correction

      Parts

      • No parts are required for this repair.

      Caution

      • All of these tests are much more effective if the throttle body is covered or sealed.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to Buick, Cadillac, Chevrolet and GMC passenger cars and trucks, model years 2000 to 2022, gasoline engines only.
    • Condition：Customers may comment that the MIL is illuminated.
    • Condition：Initial diagnosis may show fuel trim and O2 sensor related codes including P0101, P0137, P0138, P0140, P0141, P0157, P0158, P0160 and P0161.
    • Condition：The listed codes also include P0171, P0174, P0420, P0430, P1174 and P1175.
    • Confirm：If normal SI diagnostics do not lead to a resolution and an intake vacuum leak or exhaust leak is suspected, use the GE-52250 Variable Pressure Leak Detector (preferred), the J-41416 ultrasonic leak tester, or possibly soapy water with low pressure air into the tailpipe to find the leak.
    • Caution：All of these tests are much more effective if the throttle body is covered or sealed.
    • Confirm：For an intake leak, introduce the smoke into the brake booster hose or the oil dipstick tube; soapy water can be sprayed near the gasket, seams and all vacuum nipples.
    • Confirm：For an exhaust leak, put the hose with smoke or air into the tailpipe sealed with shop towels, then spray soapy water around seals, seams and bosses.
    • Cause：These methods find small leaks around the O2 sensor embossments and slight cracks in an intake plenum or gasket.
    • Parts：No parts are required for this repair.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.

  3. Manufacturer communication2000–2006 GMC YUKON XL ・ 2021-04-19(5 earlier editions of this document folded here)

    Induction System Icing Inspection in Cold Ambient Temperatures

    1. 1Fault

      • The check engine light comes on and engine performance is poor in very cold ambient temperatures.

    2. 2Finding the cause

      Not stated

    3. 3Correction

      This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance. Â

    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Vehicles equipped with turbocharged gasoline engines, which may set DTC P0299 or P2227.
    • Condition：The check engine light comes on and engine performance is poor in very cold ambient temperatures.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance. Â

  4. Manufacturer communication2000–2006 GMC YUKON XL ・ 2020-11-16(2 earlier editions of this document folded here)

    Misfire and DTC Code Diagnostic Information Notification

    1. 1Fault

      • The vehicle has a misfire with DTCs P0300 - P0308 and/or P050D set.

    2. 2Finding the cause

      Steps to confirm (in the document’s order)

      1. Establish whether the misfire can be felt; if it cannot, remove the accessory drive belt if possible and evaluate.
      2. Perform the fuel injector balance test and record the results.
      3. Check for a possible fuel quality issue, especially with a cold engine hard start and/or a misfire on all cylinders.
      4. Check the ignition supply voltage to the ignition module/coil assemblies and to the fuel injectors.
      5. Complete a compression test, static and running, and record the results.
      5 more points

    3. 3Correction

      This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to all brands, models and engines, 2000 - 2021.
    • Condition：The vehicle has a misfire with DTCs P0300 - P0308 and/or P050D set.
    • Confirm：Establish whether the misfire can be felt; if it cannot, remove the accessory drive belt if possible and evaluate.
    • Confirm：Perform the fuel injector balance test and record the results.
    • Confirm：Check for a possible fuel quality issue, especially with a cold engine hard start and/or a misfire on all cylinders.
    • Confirm：Check the ignition supply voltage to the ignition module/coil assemblies and to the fuel injectors.
    • Confirm：Complete a compression test, static and running, and record the results.
    • Confirm：Complete a cylinder leakage test if needed and record the results.
    • Confirm：Note whether the fuel trims are rich or lean.
    • Confirm：Inspect the spark plugs for anything abnormal.
    • Confirm：Swap components from the misfiring cylinder to known good locations.
    • Confirm：Confirm that a crankshaft variation learn has been completed.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

  5. Manufacturer communication2000–2006 GMC YUKON XL ・ 2017-08-15(1 earlier editions of this document folded here)

    Engine Check Lamp P0442 Evaporative Emissions System Notification

    1. 1Fault

      • The service engine soon lamp (MIL) is on for DTC P0442, but a leak cannot be verified with the system test in the service information.

    2. 2Finding the cause

      Steps to confirm (in the document’s order)

      1. With the scan tool, command the EVAP system CLOSED, start the engine and watch the tank pressure sensor value for about two minutes.
      2. If the tank pressure value changes (shows vacuum), remove the purge solenoid and pressurize its fuel tank side with the GE 41413-A / J 41413-A tester.
      3. If the tank pressure value does not change, install the CH-48096 adaptor between the purge line from the canister and the purge solenoid; use no other adaptor or pressurization method.
      4. With the EVAP system CLOSED, pressurize through the adaptor and let the system stabilize, watching the gauge for at least 5 minutes, then add smoke.
      5. Look for smoke or UV trace fluid at the purge solenoid, the engine side, the fuel cap or capless fill door, and the canister vent solenoid filter or fresh-air line.
      1 more points

    3. 3Correction

      Repair

      • If smoke passes through the purge solenoid, replace the purge solenoid.

      Caution

      • After verifying P0442, do not disturb any fuel system component before testing.
      • Test pressure must not exceed 13 in H2O (0.5 PSI (= 3.45 kPa)); more can make components perform inaccurately and lead to misdiagnosis.
      • A large temperature difference between vehicle, shop and tester seriously affects accuracy; let the vehicle adjust to shop temperature first.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to 2016 and prior passenger cars and trucks.
    • Condition：The service engine soon lamp (MIL) is on for DTC P0442, but a leak cannot be verified with the system test in the service information.
    • Caution：After verifying P0442, do not disturb any fuel system component before testing.
    • Confirm：With the scan tool, command the EVAP system CLOSED, start the engine and watch the tank pressure sensor value for about two minutes.
    • Confirm：If the tank pressure value changes (shows vacuum), remove the purge solenoid and pressurize its fuel tank side with the GE 41413-A / J 41413-A tester.
    • Repair：If smoke passes through the purge solenoid, replace the purge solenoid.
    • Confirm：If the tank pressure value does not change, install the CH-48096 adaptor between the purge line from the canister and the purge solenoid; use no other adaptor or pressurization method.
    • Confirm：With the EVAP system CLOSED, pressurize through the adaptor and let the system stabilize, watching the gauge for at least 5 minutes, then add smoke.
    • Confirm：Look for smoke or UV trace fluid at the purge solenoid, the engine side, the fuel cap or capless fill door, and the canister vent solenoid filter or fresh-air line.
    • Confirm：If smoke testing finds nothing, the leak may exist only under vacuum: use the scan tool Purge/Seal function to pull a vacuum and watch the FTP sensor parameter for vacuum decay.
    • Caution：Test pressure must not exceed 13 in H2O (0.5 PSI (= 3.45 kPa)); more can make components perform inaccurately and lead to misdiagnosis.
    • Caution：A large temperature difference between vehicle, shop and tester seriously affects accuracy; let the vehicle adjust to shop temperature first.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.

ENGINE3

  1. Manufacturer communication2000–2006 GMC YUKON XL DENALI ・ 2024-07-16(4 earlier editions of this document folded here)

    Fuel Injection Cleaner Kit Service Bulletin

    1. 1Fault

      • Rough idle, crank no start, extended crank or misfire, with the engine warning lamp on and DTC P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308 set.
      • When the engine is cold, compression on multiple cylinders may be zero.
      • The engine may pop through the intake or exhaust while cranking, and the spark plugs may be fuel fouled.

    2. 2Finding the cause

      Possible causes

      • Major carbon build-up on the intake and/or exhaust valves from fuel contamination or incomplete burning of the fuel; misfires should not appear before at least 8,000 km (5,000 mi).

    3. 3Correction

      Repair

      1. If there is no valve damage and no cam follower out of place, perform the cleaning procedure to free sticking valves and remove carbon from the valves and pistons.
      2. If valves are damaged or cam followers are out of place, make the engine mechanical repairs first and then perform the cleaning procedure to prevent a return.
      3. Fill Cleaner Kit J-35800-A with about 650 ml (22 oz, 2 cans) of Air Intake, Combustion Chamber Cleaner and set the air pressure at the tool to 260 kPa (40 psi).
      4. With GDS 2 or a scan tool, command engine idle to 2000 rpm so the engine does not stall.
      5. With the engine at operating temperature in a well-ventilated area, slowly and carefully induce the cleaner into the engine, taking about 3 minutes.

      Parts

      • The Top Engine Cleaning Kit (ACDelco Air Intake, Valve and Combustion Chamber Cleaner and ACDelco Fuel System Cleaner 44K) is 19435372 for the U.S. and Canada.

      Part numbers printed in the document

      The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

      Caution

      • Inducing too much cleaner at too low an RPM, or stalling the engine with too much cleaner at once, may hydro-lock the engine and bend a connecting rod.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to GM passenger cars and trucks with gasoline engines only, model years 2000 to 2025.
    • Condition：Rough idle, crank no start, extended crank or misfire, with the engine warning lamp on and DTC P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308 set.
    • Condition：When the engine is cold, compression on multiple cylinders may be zero.
    • Condition：The engine may pop through the intake or exhaust while cranking, and the spark plugs may be fuel fouled.
    • Cause：Major carbon build-up on the intake and/or exhaust valves from fuel contamination or incomplete burning of the fuel; misfires should not appear before at least 8,000 km (5,000 mi).
    • Repair：If there is no valve damage and no cam follower out of place, perform the cleaning procedure to free sticking valves and remove carbon from the valves and pistons.
    • Repair：If valves are damaged or cam followers are out of place, make the engine mechanical repairs first and then perform the cleaning procedure to prevent a return.
    • Caution：Inducing too much cleaner at too low an RPM, or stalling the engine with too much cleaner at once, may hydro-lock the engine and bend a connecting rod.
    • Repair：Fill Cleaner Kit J-35800-A with about 650 ml (22 oz, 2 cans) of Air Intake, Combustion Chamber Cleaner and set the air pressure at the tool to 260 kPa (40 psi).
    • Repair：With GDS 2 or a scan tool, command engine idle to 2000 rpm so the engine does not stall.
    • Repair：With the engine at operating temperature in a well-ventilated area, slowly and carefully induce the cleaner into the engine, taking about 3 minutes.
    • Parts：The Top Engine Cleaning Kit (ACDelco Air Intake, Valve and Combustion Chamber Cleaner and ACDelco Fuel System Cleaner 44K) is 19435372 for the U.S. and Canada.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This service bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.

  2. Owner complaint2000 GMC YUKON XL ・ 2017-12-20

    Vehicle stalls while driving at 55 MPH with sputtering noise

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3CorrectionNot repaired

      THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED.

    Read the sentences of the record
    Fault
    WHILE DRIVING 55 MPH (= 88.5 km/h), THE VEHICLE MADE A SPUTTERING NOISE AND STALLED. (1 more)
    Remedy
    THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED.

  3. Manufacturer communication2000–2006 GMC YUKON XL ・ 2017-08-15(1 earlier editions of this document folded here)

    Engine Misfire and Rough Idle Malfunction Indicator Lamp

    1. 1Fault

      • Customers may complain of a MIL and/or engine misfire, rough idle, extended crank, or crank no start.
      • One or more misfire codes (DTC P0300-P0308) are found stored in the ECM.

    2. 2Finding the cause

      Possible causes

      • The condition may result from major carbon build up on the intake and/or exhaust valves due to fuel contamination or incomplete burning of the fuel.

      Steps to confirm (in the document’s order)

      1. With the engine cold, compression on multiple cylinders may read 0 PSI (= 0 kPa).
      2. The engine may pop through the intake or exhaust while cranking, and the spark plugs may be fuel fouled.

    3. 3Correction

      Repair

      1. If there is valve damage or cam followers are out of place, make the mechanical repairs first, then perform the cleaning procedure to keep the concern from returning.
      2. With the engine at operating temperature, slowly induce a bottle of GM Upper Engine and Fuel Injection Cleaner with RPM held above idle so the engine does not stall (typically around 2,000 RPM).
      3. Turn the engine off and let the cleaner soak for 2.5 to 3 hours.
      4. To complete the repair, change the engine oil and filter.

      Parts

      • Upper Engine and Fuel Injector Cleaner is P/N 88861803 (in Canada, P/N 88861804).

      Part numbers printed in the document

      The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

      Caution

      • Inducing too much cleaner at too low an RPM, or stalling the engine with cleaner, may hydro-lock the engine and bend a connecting rod.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to all 2000-2015 light duty trucks with gasoline engines.
    • Condition：Customers may complain of a MIL and/or engine misfire, rough idle, extended crank, or crank no start.
    • Condition：One or more misfire codes (DTC P0300-P0308) are found stored in the ECM.
    • Cause：The condition may result from major carbon build up on the intake and/or exhaust valves due to fuel contamination or incomplete burning of the fuel.
    • Confirm：With the engine cold, compression on multiple cylinders may read 0 PSI (= 0 kPa).
    • Confirm：The engine may pop through the intake or exhaust while cranking, and the spark plugs may be fuel fouled.
    • Repair：If there is valve damage or cam followers are out of place, make the mechanical repairs first, then perform the cleaning procedure to keep the concern from returning.
    • Repair：With the engine at operating temperature, slowly induce a bottle of GM Upper Engine and Fuel Injection Cleaner with RPM held above idle so the engine does not stall (typically around 2,000 RPM).
    • Repair：Turn the engine off and let the cleaner soak for 2.5 to 3 hours.
    • Repair：To complete the repair, change the engine oil and filter.
    • Caution：Inducing too much cleaner at too low an RPM, or stalling the engine with cleaner, may hydro-lock the engine and bend a connecting rod.
    • Parts：Upper Engine and Fuel Injector Cleaner is P/N 88861803 (in Canada, P/N 88861804).

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed.

ELECTRICAL1

  1. Recall2000–2001 GMC YUKON XL ・ 2005-04-15

    Fuel Module Reservoir Assembly Overheating Recall

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      Not stated

    Read the sentences of the record
    Cause
    Certain vehicles were built with fuel module reservoir assemblies that contain fuel pump wires and/or connectors that may overheat under certain operating conditions. Fuel pump wires that overheat may become exposed and result in one or more conditions; 1) If the ignition circuit wire is exposed and shorts to ground, the fuel pump fuse will blow, disabling the fuel pump and causing an engine stall or no-start condition. 2) If sufficient heat is conducted to the pass-through connector, a hole in the connector may result, which may cause the Service Engine Soon light to be illuminated during the emission system diagnostics routine. Fuel vapour (and in some limited cases liquid fuel) may leak out of the fuel tank through the hole in the connector body. 3) If the ignition circuit or ground wire is exposed and shorts to the fuel level sender card wires, inaccurate fuel level readings may result. Correction: Dealers will affect repairs.

ELECTRICAL SYSTEM1

  1. Manufacturer communication2000–2006 GMC YUKON XL ・ 2017-08-15

    OnStar Communication Interface Module Power Issue

    1. 1Fault

      • Some Gen 6 OnStar vehicles have a no power/no connect concern; the LED may or may not be lit red and a current DTC U1500 may be present.
      • The message "PHONE UNAVAILABLE" may keep repeating without any user input.

    2. 2Finding the cause

      Not stated

    3. 3Correction

      Repair

      • OnStar Engineering found that Gen6 VCIMs with STID in the ranges 14,000,000 - 16,000,000 and/or 22,000,000 - 23,200,000 may induce this concern and need to be replaced.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to 2000-2006 GM passenger cars and trucks with OnStar Gen6.
    • Condition：Some Gen 6 OnStar vehicles have a no power/no connect concern; the LED may or may not be lit red and a current DTC U1500 may be present.
    • Condition：The message "PHONE UNAVAILABLE" may keep repeating without any user input.
    • Repair：OnStar Engineering found that Gen6 VCIMs with STID in the ranges 14,000,000 - 16,000,000 and/or 22,000,000 - 23,200,000 may induce this concern and need to be replaced.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This Preliminary Information communication provides information to the technician about vehicles may have a no power or no connect concern. Technician will find that the OnStar led is red and Diagnostic Trouble Code U1500 is set. Technician will need to replace the Vehicle Communication Interface Module if the Station Identification number falls in the ranges 14,000,000 - 16,000,000 or 22,000,000 - 23,200,000.

EQUIPMENT1

  1. Manufacturer communication2000–2006 GMC YUKON XL ・ 2021-04-19(1 earlier editions of this document folded here)

    Winter Fuel Grade Use in Warm Months 2020 – Drivability Issues

    1. 1Fault

      • In rare instances customers may complain of a fuel smell, longer starts, hesitation and, in extreme cases, engine stalls.
      • Any combination of DTCs P0300, P0171, P0174 and P228C may be set.

    2. 2Finding the cause

      Possible causes

      • Using winter fuel in summer weather may cause drivability concerns.

      Steps to confirm (in the document’s order)

      • The concern should not be a single event but multiple occurrences associated with hot days.

    3. 3Correction

      Caution

      • No repair is required; the vehicles are not damaged and will recover.
      • There is no other remedy until summer fuel and/or cooler weather is available.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to all brands and models with gasoline engines, model years 2000 - 2022.
    • Applies to：The involved region is North America.
    • Condition：In rare instances customers may complain of a fuel smell, longer starts, hesitation and, in extreme cases, engine stalls.
    • Condition：Any combination of DTCs P0300, P0171, P0174 and P228C may be set.
    • Cause：Using winter fuel in summer weather may cause drivability concerns.
    • Confirm：The concern should not be a single event but multiple occurrences associated with hot days.
    • Caution：No repair is required; the vehicles are not damaged and will recover.
    • Caution：There is no other remedy until summer fuel and/or cooler weather is available.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use.  Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement.  This will extend the use of winter fuel into the summer months. The drivability concerns should not be single events but should be multiple occurrences associated with hot days.

FUEL SYSTEM, GASOLINE1

  1. Manufacturer communication2000–2006 GMC YUKON XL ・ 2018-05-21(1 earlier editions of this document folded here)

    E85 Fuel Effects on Non-E85 Vehicles Information

    1. 1Fault

      • Using this fuel in a non-compatible vehicle may cause lean driveability concerns such as hesitation, sag and/or possible stalling.
      • Fuel trim DTC P0171 and/or P0174 may set.
      • Misfire DTC P0300 may set.
      • A Traction Control, Stability System or ABS lamp may illuminate, or a message may display in the DIC (if equipped).
      • Harsh and/or firm transmission shifts may occur because the transmission defaults to maximum line pressure.

    2. 2Finding the cause

      Steps to confirm (in the document’s order)

      1. Alcohol content is checked using Special Tool J-44175-A Fuel Composition Tester or CH-44175-A Fuel Composition Tester.
      2. General Motors started putting yellow gas caps on E85 Flex Fuel Vehicles (FFVs) as of Model Year 2006.

    3. 3Correction

      Repair

      • If the ethanol content exceeds the Owner Manual maximum of 10% or 15%, drain the fuel and refill the vehicle with gasoline, preferably a Top Tier brand.

      Caution

      • All Model Year 2011 and older non-FFV gasoline vehicles are designed to run on fuel containing no more than 10% ethanol.
      • Diesel engines are not E85 compatible.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：The list of compatible flexible-fuel vehicles includes 2002–2005 fullsize pickups and utilities with 5.3L, RPO L59.
    • Applies to：The list of compatible flexible-fuel vehicles includes 2006 Sierra, Yukon and Yukon XL with 5.3L, RPO L59.
    • Caution：All Model Year 2011 and older non-FFV gasoline vehicles are designed to run on fuel containing no more than 10% ethanol.
    • Caution：Diesel engines are not E85 compatible.
    • Condition：Using this fuel in a non-compatible vehicle may cause lean driveability concerns such as hesitation, sag and/or possible stalling.
    • Condition：Fuel trim DTC P0171 and/or P0174 may set.
    • Condition：Misfire DTC P0300 may set.
    • Condition：A Traction Control, Stability System or ABS lamp may illuminate, or a message may display in the DIC (if equipped).
    • Condition：Harsh and/or firm transmission shifts may occur because the transmission defaults to maximum line pressure.
    • Confirm：Alcohol content is checked using Special Tool J-44175-A Fuel Composition Tester or CH-44175-A Fuel Composition Tester.
    • Repair：If the ethanol content exceeds the Owner Manual maximum of 10% or 15%, drain the fuel and refill the vehicle with gasoline, preferably a Top Tier brand.
    • Confirm：General Motors started putting yellow gas caps on E85 Flex Fuel Vehicles (FFVs) as of Model Year 2006.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This informational bulletin provides the technician with information on what E85 fuel may due to a non E85 vehicle.

Showing 17 of the 51 you can open. Narrow the search to see the rest.