GMC Yukon XL 2000–2006
Common on this vehicle:Gauge or instrument faultWarning lightCorrosion or rustNoiseLeakReduced brakingStalls or shuts offLoss of engine power, no acceleration
Possible causes
17 causes not drawn
- Throttle body carbon build-up: idle surge, reduced engine power, throttle DTCs (high mileage)0
- Stability System Disabled / Service Stability message with DTC C0455 (bent terminals at the steering wheel position sensor)1
- Front right-hand brake pipe contact with body cross sill - recall 00V-3450
- ABS lamp with DTC C0265 (EBCM motor relay circuit) after EBCM replacement0
- Air bag lamp on with DTC B0092 (passenger presence system sensor harness)1
- SIR lamp on and inside mirror temperature/compass display inoperative (open air bag fuse, circuit 1139 shorted to ground)1
- Seat Belt Buckle: failed1
- Seat Belt Warning Light: failed1
- Air bag (SIR) lamp on with DTC B1001 after BCM or SDM replacement0
- Service 4WD indicator and DTC B2725 (transfer case shift control switch)4WD / AWD only1
- 4WD/AWD lamps and system inoperative: "sleepy" New Venture Gear transfer case control module (reprogram the TCCM)4WD / AWD only1
- No response when the OnStar button is pressed (DTC B2476): button assembly test values1
- Red OnStar LED and DTC B2455 after Canada upgrade bulletin 15-08-44-001 (audio and microphone drain wires shorted)1
- Rear HVAC ticking noise, no rear temperature or mode control, DTC B0434 / B3764 (revised auxiliary HVAC control module)1
- Instrument panel cluster gauges stick, flutter or stop working1
- Bolt: loose or misadjusted1
- Quadrasteer: rear wheels stay turned after the front wheels are straight (controlled re-centering after a fault, normal operation)1
Causes with no correction stated (14)
Causes the records name for which no check or repair is stated, in a technical document or in a record. Press one for the records that name it.
- Brakes
- Electronic Brake Control Module: failed (8)Brake Rotor: worn (1)Service Stability message with DTC C0131, C0196, C0290 and/or C0292 (0)
- Exhaust and emissions
- Exhaust Manifold Bolt: broken (2)
- Electrical, wiring and power
- TAC Module: electrical fault, failed (2)Ignition Circuit Or Ground Wire: electrical fault (1)Pass-Through Connector: broken (1)Powertrain Control Module: software (1)Intermittent no start with Service Stability, ABS light, 'Unknown Driver' and multiple DTCs / no module communication (0)
- Body, doors and interior
- Seat Position Sensor: broken (1)
- Transmission and driveline
- Transmission: failed (1)Transmission Range Switch: failed (1)
The documents say what to doOnly records name itThe size of a node, the width of a link and the numbers are records matching this search, not likelihoods.
FaultCrate・GMC Yukon XL 2000–2006・Warning light
Candidate cause (the documents say what to do)
Transfer case service light, New Venture Gear transfer case (replace the encoder motor sensor and reprogram the TCCM)
0 of the records matching this search name this component as the cause.
How to tell
C0327P0500P0836Service 4WD
What to do
- Verify that the encoder motor is the primary cause.
- Replace the encoder motor sensor and reprogram the TCCM; the labor operation is K9980.
Caution: Do not replace the module, the encoder motor or the transfer case for DTCs C0327, P0836, P0500; the reference is bulletin 03-04-21-001D.
What is needed
- Parts and materials
- Encoder motor sensor
- Labor time
- Labor Operation: K9980
- Special tools
- Not stated
- Scan tool
- Reprogramming of the TCCM
Only what the technical documents state. "Not stated" does not mean not needed.
In the records
No record states work done for this cause.
See the evidence (1 technical documents, 0 records)
Passages of the technical documents
Row for 2003 Fullsize Pickups and Utilities: transfer case service light, New Venture Gear transfer case.
2003 Fullsize Pickups and Utilities – Transfer Case Service Light/New Venture Gear Transfer Case
General Motors 2004-04-01
Verify that the encoder motor is the primary cause.
Verify that the encoder motor is the primary cause.
General Motors 2004-04-01
Replace the encoder motor sensor and reprogram the TCCM; the labor operation is K9980.
Replace encoder motor sensor and reprogram TCCM. Labor Operation: K9980
General Motors 2004-04-01
Do not replace the module, the encoder motor or the transfer case for DTCs C0327, P0836, P0500; the reference is bulletin 03-04-21-001D.
Don’t replace the module, encoder motor or transfer case for DTCs C0327, P0836, P0500 03-04-21-001D
General Motors 2004-04-01
A cause or a result a complaint states is the owner’s view or what a dealer told them, not an established fact.
Put together by FaultCrate from public records and technical documents. The cause and the repair are for the workshop to decide with the vehicle in front of it. Counts are records, not failure rates.