Skip to content
FaultCrate
日本語

This is an open preview: every record can be read without an account.

GMC Yukon XL 2000–2006

GMC Yukon XLModel years 2000–2006

Change vehicle →
Clear the search
3 conditions added

Common on this vehicle:Warning light

Possible causes

Warning light, Stability control message (StabiliTrak), 20051 records
Brakes
Electrical, wiring and power
Engine
Exhaust and emissions
Airbags and seat belts
Suspension, wheels and tires
1Stability System Disabled / Service Stability message with DTC C0455 (bent terminals at the steering wheel position sensor)0ABS lamp with DTC C0265 (EBCM motor relay circuit) after EBCM replacement0Brake pipe (brake line) corrosion and rupture0ABS light with C0265/C0201/U1041 or no communication with brake module (EBCM ground G110)0Intermittent battery lamp with history DTC B1489 after BGCM replacement (module not SPS programmed)0Intermittent MIL, service lamps/messages or DTCs from connector fretting corrosion0Reduced Engine Power from throttle body connector crimp, broken wire or grounds0Intake manifold gasket leak (cold idle misfire, lean codes)0Single-cylinder misfire (P0300-P0308) and/or chirp, squeak or tick at camshaft speed: worn cam lobe / lifter, valve or valve spring0P0300 after engine repairs: injector connectors crossed (cylinders 5-7 / 6-8)0P0420 / P0430 on a new or just-replaced catalytic converter (break-in not completed)0SIR lamp on and inside mirror temperature/compass display inoperative (open air bag fuse, circuit 1139 shorted to ground)0Air bag (SIR) lamp on with DTC B1001 after BCM or SDM replacement0Autoride (Z55) Service Ride Control / Service Suspension System message0Aftermarket part (not the vehicle as built): Federal-Mogul National / Carquest replacement wheel hub assembly retention nut - recall 07E-1062WD only
Causes with no correction stated (2)

Causes the records name for which no check or repair is stated, in a technical document or in a record. Press one for the records that name it.

Electrical, wiring and power
Intermittent no start with Service Stability, ABS light, 'Unknown Driver' and multiple DTCs / no module communication (0)
Brakes
Service Stability message with DTC C0131, C0196, C0290 and/or C0292 (0)

The documents say what to doOnly records name itThe size of a node, the width of a link and the numbers are records matching this search, not likelihoods.

FaultCrate・GMC Yukon XL 2000–2006・Warning light, Stability control message (StabiliTrak), 2005

Candidate cause (the documents say what to do)

Stability System Disabled / Service Stability message with DTC C0455 (bent terminals at the steering wheel position sensor)

Owners may comment on a Stability System Disabled or Service Stability message with DTC C0455.

The concern may be caused by bent terminals on the SWPS (Steering Wheel Position Sensor).

How to tell

C0455Stability control message (StabiliTrak)

What to do

  1. Remove the SWPS connector and inspect for bent terminals.
  2. In most cases the terminals can be straightened without replacing the sensor.

What is needed

Parts and materials
Not stated
Labor time
Not stated
Special tools
Not stated
Scan tool
Not stated

Only what the technical documents state. "Not stated" does not mean not needed.

In the records

No record states work done for this cause.

See the evidence (2 technical documents, 1 records)

Passages of the technical documents

  • Applies to 2005 Cadillac, Chevrolet and GMC Full Size Utilities with RPO JL4.

    This information applies to 2005 Cadillac, Chevrolet, and GMC Full Size Utilities with RPO JL4.

    General Motors 2005-07-01

  • Owners may comment on a Stability System Disabled or Service Stability message with DTC C0455.

    Owners may comment on a Stability System Disabled or Service Stability message with DTC C0455.

    General Motors 2005-07-01

  • The concern may be caused by bent terminals on the SWPS (Steering Wheel Position Sensor).

    This concern may be caused by bent terminals on the SWPS (Steering Wheel Position Sensor).

    General Motors 2005-07-01

  • Remove the SWPS connector and inspect for bent terminals.

    Remove the SWPS connector and inspect for bent terminals.

    General Motors 2005-07-01

Read every statement and its source →

Records

None among the records that can be opened now.

See all 1 records of this cause →

A cause or a result a complaint states is the owner’s view or what a dealer told them, not an established fact.

Put together by FaultCrate from public records and technical documents. The cause and the repair are for the workshop to decide with the vehicle in front of it. Counts are records, not failure rates.