Skip to content
FaultCrate
日本語

This is an open preview: every record can be read without an account.

GMC Yukon 2000–2006

GMC YukonModel years 2000–2006

Change vehicle →
Clear the search
2 conditions added

Common on this vehicle:Warning lightNoiseLeakGauge or instrument faultMisfire or rough idleVibration or shudderCorrosion or rustAir conditioning or heater

Record by record

15 records state a cause or a remedy. Each record is shown as short labels in the order fault → finding the cause → correction. Press a label to narrow to the records that state it.

Symptom

Component named as the cause

Work done

A ribbon is as wide as the records that state both of its ends (only the commonest are drawn). A record that names several symptoms or components runs through each. Orange is records that say the fault came back or was not fixed. Results come from owners’ reports only; one that does not say is “result not stated”. None of this is a likelihood of a cause or a rate at which work succeeds.

Read the records one by one (9)

Known issuesIntermittent stall, misfire or crank no start (Ignition 1 feed wire broken near C148/C149)2

  1. Manufacturer communication2005–2006 GMC YUKON ・ 2006-10-01

    Intermittent stall, misfire or crank no start: Ignition 1 feed wire broken near C148/C149

    1. 1Fault

      • The engine may intermittently stall, misfire, or crank without starting, and there may be no trouble codes set.

    2. 2Finding the cause

      Possible causes

      • The pink Ignition 1 power feed wire may break inside the insulation near connector C148/C149.

      Steps to confirm (in the document’s order)

      1. Complete the SI diagnostics first; if they are inconclusive and the concern can be duplicated, inspect for a loss of Ignition 1 voltage to the ignition coils.
      2. Wiggle test the ignition coil harnesses to see if the concern can be duplicated.
      3. Inspect splices S160 and S159 for loose connections, and connectors C148 and C149 for wires breaking near the connector.

    3. 3Correction

      Broken Ignition Wire This information applies to the 2005-06 Chevrolet Express, Silverado, Suburban, Tahoe, GMC Savana, Sierra, Yukon equipped with a 4.8, 5.3 or 6.0 engine. The engine may intermittently stall, misfire, or crank without starting. There may be no trouble codes set. Complete the SI diagnostics for any symptoms or trouble codes found. If diagnostics are inconclusive, and an intermittent stall, misfire, or a crank no start can be duplicated, inspect for a loss of Ignition 1 voltage to the ignition coils. Wiggle test the ignition coil harnesses to see if the concern can be duplicated. Inspect splices S160 and S159 for loose connections. Also inspect connectors C148 and C149 for wires breaking near the connector. The pink Ignition 1 power feed wire may break inside the insulation near connector C148/C149.

      What the documents say to do

      Intermittent stall, misfire or crank no start (Ignition 1 feed wire broken near C148/C149)

      Confirm

      • Complete the SI diagnostics first; if they are inconclusive and the concern can be duplicated, inspect for a loss of Ignition 1 voltage to the ignition coils.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：The information applies to 2005-06 Chevrolet Express, Silverado, Suburban, Tahoe, GMC Savana, Sierra and Yukon equipped with a 4.8, 5.3 or 6.0 engine.
    • Condition：The engine may intermittently stall, misfire, or crank without starting, and there may be no trouble codes set.
    • Confirm：Complete the SI diagnostics first; if they are inconclusive and the concern can be duplicated, inspect for a loss of Ignition 1 voltage to the ignition coils.
    • Confirm：Wiggle test the ignition coil harnesses to see if the concern can be duplicated.
    • Confirm：Inspect splices S160 and S159 for loose connections, and connectors C148 and C149 for wires breaking near the connector.
    • Cause：The pink Ignition 1 power feed wire may break inside the insulation near connector C148/C149.

    Open this issue of GM TechLink ↗ The points above are read from an article of TechLink, GM’s monthly publication for dealership technicians. The article itself is not reproduced here.

    Remedy
    Broken Ignition Wire This information applies to the 2005-06 Chevrolet Express, Silverado, Suburban, Tahoe, GMC Savana, Sierra, Yukon equipped with a 4.8, 5.3 or 6.0 engine. The engine may intermittently stall, misfire, or crank without starting. There may be no trouble codes set. Complete the SI diagnostics for any symptoms or trouble codes found. If diagnostics are inconclusive, and an intermittent stall, misfire, or a crank no start can be duplicated, inspect for a loss of Ignition 1 voltage to the ignition coils. Wiggle test the ignition coil harnesses to see if the concern can be duplicated. Inspect splices S160 and S159 for loose connections. Also inspect connectors C148 and C149 for wires breaking near the connector. The pink Ignition 1 power feed wire may break inside the insulation near connector C148/C149.

  2. Manufacturer communication2005–2006 GMC YUKON ・ 2006-09-28

    Loss of Ignition 1 Voltage to the Ignition Coils

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      LOSS OF IGNITION 1 VOLTAGE TO THE IGNITION COILS. CONSUMER EXPERIENCED INTERMITTENT STALL, MISFIRE, OR CRANK NO START. THERE MAY BE NO TROUBLE CODES SET. *KB UPDATED 3/17/09. *PE

      What the documents say to do

      Intermittent stall, misfire or crank no start (Ignition 1 feed wire broken near C148/C149)

      Confirm

      • Complete the SI diagnostics first; if they are inconclusive and the concern can be duplicated, inspect for a loss of Ignition 1 voltage to the ignition coils.
    Read the sentences of the record
    Remedy
    LOSS OF IGNITION 1 VOLTAGE TO THE IGNITION COILS. CONSUMER EXPERIENCED INTERMITTENT STALL, MISFIRE, OR CRANK NO START. THERE MAY BE NO TROUBLE CODES SET. *KB UPDATED 3/17/09. *PE

Known issuesOut of fuel with the gauge reading above empty, cranks but no start, stall (replace the fuel sensor, not the sender module)1

  1. Manufacturer communication2001–2005 GMC FULL SIZE PICKUPS AND UTILITIES (YUKON) ・ 2005-12-01

    Cranks but no start, stall, or inaccurate fuel gauge with the tank out of fuel: replace the fuel sensor

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      Repair

      • Replace the fuel sensor.

      Caution

      • Do not replace the fuel sender module; the reference is bulletin 04-08-49-018E.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Row for 2001-2005 Full Size Pickups and Utilities: cranks but no start, stall, inaccurate/incorrect fuel gauge reading, no fuel, vehicle is out of fuel and the fuel gauge reads above empty.
    • Repair：Replace the fuel sensor.
    • Caution：Do not replace the fuel sender module; the reference is bulletin 04-08-49-018E.

    Open this issue of GM TechLink ↗ The points above are read from an article of TechLink, GM’s monthly publication for dealership technicians. The article itself is not reproduced here.

    Remedy
    Truck Issues — Fix It Right the First Time (new issues in bold) 2001-2005 Full Size Pickups and Utilities – Cranks But No Start, Stall, Inaccurate/Incorrect Fuel Gauge Reading, No Fuel, Vehicle is Out of Fuel and Fuel Gauge Reads Above Empty Replace fuel sensor. Don’t replace fuel sender module. 04-08-49-018E

Known issuesIntermittent no start with Service Stability, ABS light, 'Unknown Driver' and multiple DTCs / no module communication1

  1. Manufacturer communication2003–2006 GMC YUKON ・ 2003-12-05

    Intermittent No Start, Stability Message, ABS Light

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      INTERMITTENT NO START, SERVICE STABILITY MESSAGE, ANTI-LOCK BRAKE SYSTEM (ABS) LIGHT ILLUMINATED, MULTIPLE DIAGNOSTIC TROUBLE CODES (DTCS), DIC SHOWS UNKNOWN DRIVER, VARIOUS ELECTRICAL RELATED CONDITIONS. INCLUDES ESCALADE ESV AND EXT MODEL. *TT

    Read the sentences of the record
    Remedy
    INTERMITTENT NO START, SERVICE STABILITY MESSAGE, ANTI-LOCK BRAKE SYSTEM (ABS) LIGHT ILLUMINATED, MULTIPLE DIAGNOSTIC TROUBLE CODES (DTCS), DIC SHOWS UNKNOWN DRIVER, VARIOUS ELECTRICAL RELATED CONDITIONS. INCLUDES ESCALADE ESV AND EXT MODEL. *TT

ENGINE3

  1. Manufacturer communication2000–2006 GMC YUKON DENALI ・ 2024-07-16(5 earlier editions of this document folded here)

    Fuel Injection Cleaner Kit Service Bulletin

    1. 1Fault

      • Rough idle, crank no start, extended crank or misfire, with the engine warning lamp on and DTC P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308 set.
      • When the engine is cold, compression on multiple cylinders may be zero.
      • The engine may pop through the intake or exhaust while cranking, and the spark plugs may be fuel fouled.

    2. 2Finding the cause

      Possible causes

      • Major carbon build-up on the intake and/or exhaust valves from fuel contamination or incomplete burning of the fuel; misfires should not appear before at least 8,000 km (5,000 mi).

    3. 3Correction

      Repair

      1. If there is no valve damage and no cam follower out of place, perform the cleaning procedure to free sticking valves and remove carbon from the valves and pistons.
      2. If valves are damaged or cam followers are out of place, make the engine mechanical repairs first and then perform the cleaning procedure to prevent a return.
      3. Fill Cleaner Kit J-35800-A with about 650 ml (22 oz, 2 cans) of Air Intake, Combustion Chamber Cleaner and set the air pressure at the tool to 260 kPa (40 psi).
      4. With GDS 2 or a scan tool, command engine idle to 2000 rpm so the engine does not stall.
      5. With the engine at operating temperature in a well-ventilated area, slowly and carefully induce the cleaner into the engine, taking about 3 minutes.

      Parts

      • The Top Engine Cleaning Kit (ACDelco Air Intake, Valve and Combustion Chamber Cleaner and ACDelco Fuel System Cleaner 44K) is 19435372 for the U.S. and Canada.

      Part numbers printed in the document

      The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

      Caution

      • Inducing too much cleaner at too low an RPM, or stalling the engine with too much cleaner at once, may hydro-lock the engine and bend a connecting rod.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to GM passenger cars and trucks with gasoline engines only, model years 2000 to 2025.
    • Condition：Rough idle, crank no start, extended crank or misfire, with the engine warning lamp on and DTC P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308 set.
    • Condition：When the engine is cold, compression on multiple cylinders may be zero.
    • Condition：The engine may pop through the intake or exhaust while cranking, and the spark plugs may be fuel fouled.
    • Cause：Major carbon build-up on the intake and/or exhaust valves from fuel contamination or incomplete burning of the fuel; misfires should not appear before at least 8,000 km (5,000 mi).
    • Repair：If there is no valve damage and no cam follower out of place, perform the cleaning procedure to free sticking valves and remove carbon from the valves and pistons.
    • Repair：If valves are damaged or cam followers are out of place, make the engine mechanical repairs first and then perform the cleaning procedure to prevent a return.
    • Caution：Inducing too much cleaner at too low an RPM, or stalling the engine with too much cleaner at once, may hydro-lock the engine and bend a connecting rod.
    • Repair：Fill Cleaner Kit J-35800-A with about 650 ml (22 oz, 2 cans) of Air Intake, Combustion Chamber Cleaner and set the air pressure at the tool to 260 kPa (40 psi).
    • Repair：With GDS 2 or a scan tool, command engine idle to 2000 rpm so the engine does not stall.
    • Repair：With the engine at operating temperature in a well-ventilated area, slowly and carefully induce the cleaner into the engine, taking about 3 minutes.
    • Parts：The Top Engine Cleaning Kit (ACDelco Air Intake, Valve and Combustion Chamber Cleaner and ACDelco Fuel System Cleaner 44K) is 19435372 for the U.S. and Canada.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This service bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.

  2. Manufacturer communication2000–2006 GMC YUKON DENALI ・ 2017-08-15(1 earlier editions of this document folded here)

    Engine Misfire and Rough Idle Malfunction Indicator Lamp

    1. 1Fault

      • Customers may complain of a MIL and/or engine misfire, rough idle, extended crank, or crank no start.
      • One or more misfire codes (DTC P0300-P0308) are found stored in the ECM.

    2. 2Finding the cause

      Possible causes

      • The condition may result from major carbon build up on the intake and/or exhaust valves due to fuel contamination or incomplete burning of the fuel.

      Steps to confirm (in the document’s order)

      1. With the engine cold, compression on multiple cylinders may read 0 PSI (= 0 kPa).
      2. The engine may pop through the intake or exhaust while cranking, and the spark plugs may be fuel fouled.

    3. 3Correction

      Repair

      1. If there is valve damage or cam followers are out of place, make the mechanical repairs first, then perform the cleaning procedure to keep the concern from returning.
      2. With the engine at operating temperature, slowly induce a bottle of GM Upper Engine and Fuel Injection Cleaner with RPM held above idle so the engine does not stall (typically around 2,000 RPM).
      3. Turn the engine off and let the cleaner soak for 2.5 to 3 hours.
      4. To complete the repair, change the engine oil and filter.

      Parts

      • Upper Engine and Fuel Injector Cleaner is P/N 88861803 (in Canada, P/N 88861804).

      Part numbers printed in the document

      The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

      Caution

      • Inducing too much cleaner at too low an RPM, or stalling the engine with cleaner, may hydro-lock the engine and bend a connecting rod.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to all 2000-2015 light duty trucks with gasoline engines.
    • Condition：Customers may complain of a MIL and/or engine misfire, rough idle, extended crank, or crank no start.
    • Condition：One or more misfire codes (DTC P0300-P0308) are found stored in the ECM.
    • Cause：The condition may result from major carbon build up on the intake and/or exhaust valves due to fuel contamination or incomplete burning of the fuel.
    • Confirm：With the engine cold, compression on multiple cylinders may read 0 PSI (= 0 kPa).
    • Confirm：The engine may pop through the intake or exhaust while cranking, and the spark plugs may be fuel fouled.
    • Repair：If there is valve damage or cam followers are out of place, make the mechanical repairs first, then perform the cleaning procedure to keep the concern from returning.
    • Repair：With the engine at operating temperature, slowly induce a bottle of GM Upper Engine and Fuel Injection Cleaner with RPM held above idle so the engine does not stall (typically around 2,000 RPM).
    • Repair：Turn the engine off and let the cleaner soak for 2.5 to 3 hours.
    • Repair：To complete the repair, change the engine oil and filter.
    • Caution：Inducing too much cleaner at too low an RPM, or stalling the engine with cleaner, may hydro-lock the engine and bend a connecting rod.
    • Parts：Upper Engine and Fuel Injector Cleaner is P/N 88861803 (in Canada, P/N 88861804).

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed.

  3. Manufacturer communication2000–2006 GMC YUKON DENALI ・ 2017-05-16

    Engine Misfire and Rough Idle Diagnostic Communication

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE A MALFUNCTION INDICATOR LAMP ON OR ENGINE MISFIRE, ROUGH IDLE, EXTENDED CRANK, OR CRANK NO START IN SOME CASES. TECHNICIAN WILL NEED TO PERFORM PUBLISHED SERVICE INFORMATION DIAGNOSTICS. IF TECHNICIAN FINDS CARBON, AN UPPER ENGINE AND VALVE CLEANING SHOULD BE PERFORMED.

    Read the sentences of the record
    Remedy
    THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE A MALFUNCTION INDICATOR LAMP ON OR ENGINE MISFIRE, ROUGH IDLE, EXTENDED CRANK, OR CRANK NO START IN SOME CASES. TECHNICIAN WILL NEED TO PERFORM PUBLISHED SERVICE INFORMATION DIAGNOSTICS. IF TECHNICIAN FINDS CARBON, AN UPPER ENGINE AND VALVE CLEANING SHOULD BE PERFORMED.

ENGINE AND ENGINE COOLING2

  1. Manufacturer communication2003–2005 GMC YUKON ・ 2004-12-17

    Crank No Start, Stall, Hard Start, and No Cranking RPM

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      CRANK NO START, STALL, HARD START, AND NO CRANKING RPM. *EH

    Read the sentences of the record
    Remedy
    CRANK NO START, STALL, HARD START, AND NO CRANKING RPM. *EH

  2. Manufacturer communication2003–2005 GMC YUKON ・ 2004-10-04

    Crank No Start with No Cranking RPM Spark or Injector Pulse

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      CRANK NO START WITH NO CRANKING RPM SPARK OR INJECTOR PULSE. *TT

    Read the sentences of the record
    Remedy
    CRANK NO START WITH NO CRANKING RPM SPARK OR INJECTOR PULSE. *TT

Showing 9 of the 15 you can open. Narrow the search to see the rest.