Skip to content
FaultCrate

This is an open preview: every record can be read without an account.

GMC Yukon 2000–2006

GMC YukonModel years 2000–2006

Change vehicle →
Clear the search
2 conditions added

The vehicle (where a record says)

A record is under an engine, a drive or a series only where it says so: the characters of the vehicle identification number filed with a complaint, its text, or what its document says it applies to. A record that does not say is kept as "not stated". The filed numbers and the documents do not tell 4WD from AWD.

Common on this vehicle:Warning lightLeakNoiseVibration or shudderMisfire or rough idleGauge or instrument faultAir conditioning or heaterCorrosion or rust

Record by record

13 records state a cause or a remedy. Each record is shown as short labels in the order fault → finding the cause → correction. Press a label to narrow to the records that state it.

A ribbon is as wide as the records that state both of its ends (only the commonest are drawn). A record that names several symptoms or components runs through each. Orange is records that say the fault came back or was not fixed. Results come from owners’ reports only; one that does not say is “result not stated”. None of this is a likelihood of a cause or a rate at which work succeeds.

Read the records one by one (12)

LATCHES/LOCKS/LINKAGES5

  1. Owner complaint2006 GMC YUKON ・ 2012-01-17

    Blower motor failure and rear door lock failure

    1. 1Fault

    2. 2Finding the cause

    3. 3CorrectionNot repaired

      THE VEHICLE WAS NOT REPAIRED.

    Read the sentences of the record
    Fault
    THE CONTACT STATED THAT THE VEHICLE BLOWER MOTOR FAILED. (1 more)
    Remedy
    THE VEHICLE WAS NOT REPAIRED.
  2. Owner complaint2006 GMC YUKON DENALI ・ 2011-07-15

    Rear liftgate unable to open, parked

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3CorrectionNot repaired

      THE VEHICLE WAS NOT REPAIRED.

    Read the sentences of the record
    Fault
    THE CONTACT STATED THAT THE VEHICLE WAS PARKED WHEN HE WAS UNABLE TO OPEN THE REAR LIFT GATE.
    Remedy
    THE VEHICLE WAS NOT REPAIRED.
  3. Owner complaint2006 GMC YUKON DENALI ・ 2010-12-28

    Door lock actuators replaced multiple times within 3 years

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

    Read the sentences of the record
    Remedy
    ALL 4 DOOR LOCK ACTUATORS HAVE BEEN REPLACED IN LESS THAN 3 YEARS.
  4. Manufacturer communication2005–2006 GMC YUKON DENALI ・ 2004-12-15

    Unable to Disable Auto Door Locks - Full Size Trucks and Utilities

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      UNABLE TO DISABLE AUTO DOOR LOCKS. THIS INCLUDES 05 CHEVROLET GMC CADILLAC FULL SIZE TRUCKS AND UTILITIES. *EH ALSO INCLUDES AVALANCE, SILVERADO SUBURBAN TAHOE; GMC SIERRA, YUKON, DENALI, YUKON XL, DENALI XL. UPDATED 8/26/08. *PE UPDATED 5/9/11. *PE

    Read the sentences of the record
    Remedy
    UNABLE TO DISABLE AUTO DOOR LOCKS. THIS INCLUDES 05 CHEVROLET GMC CADILLAC FULL SIZE TRUCKS AND UTILITIES. *EH ALSO INCLUDES AVALANCE, SILVERADO SUBURBAN TAHOE; GMC SIERRA, YUKON, DENALI, YUKON XL, DENALI XL. UPDATED 8/26/08. *PE UPDATED 5/9/11. *PE
  5. Owner complaint2006 GMC YUKON DENALI ・ 2012-08-10

    Rear liftgate will not open

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      Not stated

    Read the sentences of the record
    Fault
    THE CONTACT STATED THAT THE REAR LIFTGATE WOULD NOT OPEN.
    Inspection
    THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC FOR DIAGNOSTICS WHERE THE MECHANIC ADVISED THAT THE PLASTIC HOUSING AROUND THE CABLE THAT CONTROLLED THE REAR LIFTGATE MECHANISM WAS MELTED.

VISIBILITY2

  1. Manufacturer communication2001–2006 GMC YUKON DENALI ・ 2017-12-22

    Rear Window Defroster Contact or Tabs Service Information

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      Repair

      1. On 2007-2014 Tahoe, Suburban, Yukon and Escalade with moveable glass always replace the defroster tab (GM P/N 25916031) and the power connector (P/N 12034110); on all other vehicles reconnect the original defroster tab.
      2. Remove the rear defroster power connector and crimp a new one to the feed wire; the proper connector, P/N 12034110, is in the Packard Electrical Assortment, Tray 18, Position 5.
      3. Prepare the surface of the used defroster tab and the defroster buss bar with fine grain (500 grit) sandpaper or Emery cloth.
      4. Wipe the prepared contact area with Kent Automotive Acrysol (or equivalent) to remove residual oil or dirt.
      5. Heat the new connector on the buss bar surface to be soldered, holding the connector and defroster tab in place with long nose pliers.

      Part numbers printed in the document

      The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

      Parts

      • Silver solder: Radio Shack (The Source in Canada) 64-013, 0.022" diameter.
      • Solvent: P20005 Kent Automotive Acrysol Solvent (32 fl oz) 946 ml.

      Caution

      • Let the glass warm to the temperature inside the building; soldering creates a hot spot in the glass, so do not solder on cold glass.
      • Heating the glass excessively, or repeatedly without time to cool, may break the glass.
      • A silver-bearing solder must be used; do not attempt the repair with conventional tin/lead alloy solders.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to:Covers 2000-2015 GM passenger cars and trucks, excluding the 2015 Chevrolet Tahoe, Suburban, GMC Yukon and Cadillac Escalade.
    • Applies to:Vehicles must have the electric rear window defroster (RPO C49).
    • Repair:On 2007-2014 Tahoe, Suburban, Yukon and Escalade with moveable glass always replace the defroster tab (GM P/N 25916031) and the power connector (P/N 12034110); on all other vehicles reconnect the original defroster tab.
    • Caution:Let the glass warm to the temperature inside the building; soldering creates a hot spot in the glass, so do not solder on cold glass.
    • Caution:Heating the glass excessively, or repeatedly without time to cool, may break the glass.
    • Caution:A silver-bearing solder must be used; do not attempt the repair with conventional tin/lead alloy solders.
    • Repair:Remove the rear defroster power connector and crimp a new one to the feed wire; the proper connector, P/N 12034110, is in the Packard Electrical Assortment, Tray 18, Position 5.
    • Repair:Prepare the surface of the used defroster tab and the defroster buss bar with fine grain (500 grit) sandpaper or Emery cloth.
    • Repair:Wipe the prepared contact area with Kent Automotive Acrysol (or equivalent) to remove residual oil or dirt.
    • Repair:Heat the new connector on the buss bar surface to be soldered, holding the connector and defroster tab in place with long nose pliers.
    • Parts:Silver solder: Radio Shack (The Source in Canada) 64-013, 0.022" diameter.
    • Parts:Solvent: P20005 Kent Automotive Acrysol Solvent (32 fl oz) 946 ml.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This informational bulletin provide information for the technicians to repair the rear window defroster contact or tabs.
  2. Owner complaint2006 GMC YUKON DENALI ・ 2012-04-23

    Rear glass window exploded in driveway

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      Not stated

    Read the sentences of the record
    Fault
    ON 4/22/2012 MY REAR GLASS WINDOW EXPLODED IN MY DRIVEWAY FOR NO REASON. (1 more)

ELECTRICAL SYSTEM1

  1. Owner complaint2006 GMC YUKON ・ 2014-03-31

    Rear liftgate and rear liftgate window will not unlock or open

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      Not stated

    Read the sentences of the record
    Fault
    THE REAR LIFTGATE WILL NOT UNLOCK OR OPEN & REAR LIFTGATE WINDOW WILL NOT UNLOCK OR OPEN.

EQUIPMENT1

  1. Manufacturer communication2001–2006 GMC YUKON DENALI ・ 2018-05-21(1 earlier editions of this document folded here)

    Liftgate Applique Replacement Procedure

    1. 1Fault

      • Condition 1: a dimpling or deformation is seen near an outer edge of the liftgate center applique.
      • Condition 2: paint damage on the liftgate at the lower outboard edges of the center applique.
    2. 2Finding the cause

      Possible causes

      • The applique design might allow deformation or dimpling of its surface if the retaining nuts are overtightened.
      • The applique design together with the forming of the license plate pocket in the liftgate may let the lower outboard edges of the applique contact the liftgate.
    3. 3Correction

      Repair

      1. For 2011 or earlier vehicles, replace the liftgate center applique with the appropriate new service part from the table.
      2. To create clearance, add GM washer P/N 15911310 to the applique between the foam washer and the mounting boss at each of the four mounting stud locations.

      Part numbers printed in the document

      The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

      Parts

      • P/N 15911310 is a 0.25 mm thick Mylar washer.
      • Applique 22777530 is for GMC non-hybrid without rear vision camera (-UVC).
      • Applique 22777531 is for GMC non-hybrid with rear vision camera (&UVC).

      Part numbers printed in the document

      The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

      Caution

      • The updated applique design went into production for the 2012 model year; the applique should not need replacement on a 2012 or newer vehicle unless Condition 1 is present.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to:Applies to 2007-2013 GMC Yukon models and Yukon XL models (note: earlier Yukon model years are not listed).
    • Condition:Condition 1: a dimpling or deformation is seen near an outer edge of the liftgate center applique.
    • Cause:The applique design might allow deformation or dimpling of its surface if the retaining nuts are overtightened.
    • Condition:Condition 2: paint damage on the liftgate at the lower outboard edges of the center applique.
    • Cause:The applique design together with the forming of the license plate pocket in the liftgate may let the lower outboard edges of the applique contact the liftgate.
    • Repair:For 2011 or earlier vehicles, replace the liftgate center applique with the appropriate new service part from the table.
    • Caution:The updated applique design went into production for the 2012 model year; the applique should not need replacement on a 2012 or newer vehicle unless Condition 1 is present.
    • Repair:To create clearance, add GM washer P/N 15911310 to the applique between the foam washer and the mounting boss at each of the four mounting stud locations.
    • Parts:P/N 15911310 is a 0.25 mm thick Mylar washer.
    • Parts:Applique 22777530 is for GMC non-hybrid without rear vision camera (-UVC).
    • Parts:Applique 22777531 is for GMC non-hybrid with rear vision camera (&UVC).

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This preliminary information bulletin provides a procedure for replacement of the liftgate applique for concerns regarding the applique being deformed or dimpled or paint damage at the lower edge of the applique

EXTERIOR LIGHTING1

  1. Owner complaint2006 GMC YUKON DENALI ・ 2014-05-17

    Upper brake indicator light on rear liftgate malfunctioned

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

    Read the sentences of the record
    Fault
    THE UPPER BRAKE INDICATOR LIGHT (BAR) ON TOP OF THE REAR LIFT GATE DOOR MALFUNCTIONED.
    Cause
    IT SEEMS TO ME THAT IT SHORTED OUT OR MAY HAVE HAD WIRES THAT BECAME CORRODED.

STRUCTURE1

  1. Owner complaint2006 GMC YUKON ・ 2013-11-09

    Rear liftgate will not unlock from inside or outside

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      Not stated

    Read the sentences of the record
    Fault
    ALSO, WHEN ATTEMPTING TO UNLOCK THE MECHANISM WOULD NOT UNLOCK THE HATCH.
    Cause
    IT IS A DESIGN FLAW ALONG WITH A POORLY FUNCTIONING LOCKING MECHANISM.

UNKNOWN OR OTHER1

  1. Owner complaint2006 GMC YUKON ・ 2015-05-28

    Rear tailgate actuator not working

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

    Read the sentences of the record
    Fault
    THE REAR TAILGATE ACTUATOR QUIT WORKING. (1 more)

Showing 12 of the 13 you can open. Narrow the search to see the rest.