Skip to content
FaultCrate
日本語

This is an open preview: every record can be read without an account.

GMC Yukon 2000–2006

GMC YukonModel years 2000–2006

Change vehicle →
Clear the search
2 conditions added

The vehicle (where a record says)

A record is under an engine, a drive or a series only where it says so: the characters of the vehicle identification number filed with a complaint, its text, or what its document says it applies to. A record that does not say is kept as "not stated". The filed numbers and the documents do not tell 4WD from AWD.

Common on this vehicle:Warning lightNoiseLeakGauge or instrument faultMisfire or rough idleVibration or shudderCorrosion or rustAir conditioning or heater

Record by record

33 records state a cause or a remedy. Each record is shown as short labels in the order fault → finding the cause → correction. Press a label to narrow to the records that state it.

Symptom

Component named as the cause

Work done

How it is said to have ended

  • says it held for a while1
  • says it did not fix it1

A ribbon is as wide as the records that state both of its ends (only the commonest are drawn). A record that names several symptoms or components runs through each. Orange is records that say the fault came back or was not fixed. Results come from owners’ reports only; one that does not say is “result not stated”. None of this is a likelihood of a cause or a rate at which work succeeds.

Read the records one by one (25)

Known issuesHVAC blower motor resistor module / connector overheating2

  1. Recall2003–2006 GMC YUKON ・ 2011-02-21

    HVAC Blower Motor Resistor Module Overheating

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      Not stated

      What the documents say to do

      HVAC blower motor resistor module / connector overheating

      Repair

      1. Dealers install a new blower motor resistor and resistor module connector.
      2. Cut the wires back far enough to remove any melted insulation.

      Caution

      • The connector must be replaced even if it was replaced in an earlier repair.
    Read the sentences of the record
    Cause
    On certain vehicles, the interface between the electrical terminals of the Heating, Ventilation, and Air Conditioning (HVAC) blower relay resistor module and the wiring connector (which powers the module) may be incapable of conducting higher current levels for sustained periods of operation. In addition, moisture and other contaminants (such as road de-icing materials) may enter the fresh air intake plenum and contact the internal circuit of the module or corrode the terminals. These conditions may cause the relay resistor module or wiring connector to overheat, causing various symptoms such as: the HVAC blower may not function on certain or all blower speed settings; a burning-plastic smell or smoke may be present in the vehicle, or; the HVAC blower may run continually with the ignition in the OFF position. These warning signs could, in certain instances, be leading indicators of an impending vehicle fire, which could result in property damage and/or personal injury. Correction: Owners will be provided with additional warranty coverage for the blower motor resistor module/wiring connector overheating condition. Under this "special warranty coverage", should this condition occur within 10 years or 240,000 km from first vehicle registration, dealers will install a replacement blower motor resistor and resistor module connector.

  2. Manufacturer communication2003–2006 GMC YUKON ・ 2011-06-27

    General Motors HVAC Blower Service Campaign

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      GENERAL MOTORS SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. THE HVAC BLOWER MAY NOT WORK AT CERTAIN FUNCTIONS OR MAY BECOME INOPERABLE. THERE COULD BE A BURNING SMELL OR SMOKE. *RM UPDATED 4/6/12. *PE

      What the documents say to do

      HVAC blower motor resistor module / connector overheating

      Repair

      1. Dealers install a new blower motor resistor and resistor module connector.
      2. Cut the wires back far enough to remove any melted insulation.

      Caution

      • The connector must be replaced even if it was replaced in an earlier repair.
    Read the sentences of the record
    Remedy
    GENERAL MOTORS SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. THE HVAC BLOWER MAY NOT WORK AT CERTAIN FUNCTIONS OR MAY BECOME INOPERABLE. THERE COULD BE A BURNING SMELL OR SMOKE. *RM UPDATED 4/6/12. *PE

Known issuesHVAC temperature doors default to full hot or defrost cannot be obtained2

  1. Manufacturer communication2003–2006 GMC YUKON DENALI ・ 2008-09-05

    HVAC Temperature Door Control Concern

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      SOME CUSTOMERS MAY COMMENT ON VARIOUS HVAC CONCERNS INCLUDING TEMPERATURE DOORS DEFAULTING TO FULL HOT POSITION OR UNABLE TO OBTAIN DEFROST POSITION. *PE

    Read the sentences of the record
    Remedy
    SOME CUSTOMERS MAY COMMENT ON VARIOUS HVAC CONCERNS INCLUDING TEMPERATURE DOORS DEFAULTING TO FULL HOT POSITION OR UNABLE TO OBTAIN DEFROST POSITION. *PE

  2. Owner complaint2005 GMC YUKON DENALI ・ 2007-11-15

    Driver side and rear air conditioning blow hot air while passenger side works

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      Not stated

    Read the sentences of the record
    Fault
    THE DRIVER SIDE AND REAR AIR WOULD ONLY BLOW OUT HOT AIR LIKE THE HEATER WAS ON BUT THE PASSENGER WAS WORKING JUST FINE. (1 more)
    Outcome
    IT IS SUPPOSED TO BE FIXED.

Known issuesCoolant leak at the rear of the vehicle (auxiliary heater hose quick connector)1

  1. Manufacturer communication2005–2006 GMC YUKON ・ 2007-08-01

    Coolant leak at the rear of the vehicle: auxiliary heater hose quick connector retainer kit

    1. 1Fault

      • Some customers may comment on a coolant leak at the rear of the vehicle; bulletin 07-01-37-002 has the details.

    2. 2Finding the cause

      Possible causes

      • The condition may be due to the auxiliary heater hose quick connection leaking, or a broken retaining clip.

    3. 3Correction

      Repair

      1. Install an auxiliary heater inlet and outlet quick connector retainer kit; do not replace the entire auxiliary heater hose line set.
      2. The installation procedure is Auxiliary Heater Inlet and Outlet Hose Connector Retainer and Seal Replacement in SI (document 1887838).

      Parts

      • The retainer kit for the auxiliary heater inlet and outlet hose connector is part number 19130031, 1 per hose.

      Part numbers printed in the document

      The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

      Caution

      • The part number is available, but in the parts catalog it is not presently associated with any of the affected vehicles.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：The information applies to 2005-07 Escalade, Suburban, Tahoe and Yukon models with Auxiliary Heater (RPO C36).
    • Condition：Some customers may comment on a coolant leak at the rear of the vehicle; bulletin 07-01-37-002 has the details.
    • Cause：The condition may be due to the auxiliary heater hose quick connection leaking, or a broken retaining clip.
    • Repair：Install an auxiliary heater inlet and outlet quick connector retainer kit; do not replace the entire auxiliary heater hose line set.
    • Parts：The retainer kit for the auxiliary heater inlet and outlet hose connector is part number 19130031, 1 per hose.
    • Repair：The installation procedure is Auxiliary Heater Inlet and Outlet Hose Connector Retainer and Seal Replacement in SI (document 1887838).
    • Caution：The part number is available, but in the parts catalog it is not presently associated with any of the affected vehicles.

    Open this issue of GM TechLink ↗ The points above are read from an article of TechLink, GM’s monthly publication for dealership technicians. The article itself is not reproduced here.

    Remedy
    Coolant Leak This information applies to 2005-07 Escalade, Suburban, Tahoe and Yukon models with Auxiliary Heater (RPO C36). Some customers may comment on a coolant leak at the rear of the vehicle. Refer to bulletin 07-01-37-002 for details. This condition may be due to the auxiliary heater hose quick connection leaking, or the retaining clip is broken. Install an auxiliary heater inlet and outlet quick connector retainer kit. Do not replace the entire auxiliary heater hose line set. 19130031 Retainer Kit, Auxiliary Heater Inlet & Outlet Hose Connector 1 per hose Refer to the Auxiliary Heater Inlet and Outlet Hose Connector Retainer and Seal Replacement procedure in SI for more information on how to install this service kit (document 1887838). TIP: The part number in the table is available, but in the parts catalog it is not presently associated with any of the affected vehicles.

Known issuesRear HVAC ticking noise, no rear temperature or mode control, DTC B0434 / B3764 (revised auxiliary HVAC control module)1

  1. Manufacturer communication2003–2006 GMC YUKON ・ 2007-02-01

    Rear HVAC ticking noise, no rear temperature or mode control, DTC B0434 / B3764: revised auxiliary HVAC control module

    1. 1Fault

      • The concerns are an intermittent ticking or clicking noise from the rear HVAC system, being unable to control the rear system temperature, and being unable to change the rear system modes.
      • A defaulted door stays at the default position until the code is cleared; clearing the code lets it operate properly until overtravel occurs again.

    2. 2Finding the cause

      Possible causes

      • The HVAC actuators may hunt for the correct commanded position, and this cycling can cause a clicking or ticking noise.
      • Overtravel of the HVAC system control doors can cause the listed conditions; when it occurs a DTC sets and the door goes to a preset default position.

      Steps to confirm (in the document’s order)

      • The overtravel DTCs are B0434 for the auxiliary (rear) temperature door and B3764 for the auxiliary (rear) mode door.

    3. 3Correction

      Repair

      • Replace the auxiliary (rear) HVAC control module; it contains a new calibration that compensates for the actuator overtravel and the hunting, clicking and ticking noises.

      Parts

      • For all 2003-06 with CJ2 and C69, the auxiliary HVAC control module is part number 15832319.
      • The second design rear blower control module is 89024926 for Tahoe, Yukon and Escalade (short wheelbase) and 89018846 for Suburban, Yukon XL and Escalade ESV (long wheelbase).

      Part numbers printed in the document

      The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

      Caution

      • With the new module the rear blower speed may rise slightly (approximately 50 rpm); if the customer objects, the blower control module may be replaced with the second design blower control module.
      • Do not use the revised auxiliary HVAC control module unless one or more of the listed codes is set; it will not correct any other DTC or A/C performance concern.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：The article concerns some 2003-06 Cadillac Escalade, Chevrolet Suburban and Tahoe, and GMC Yukon models with RPO CJ2 and C69.
    • Condition：The concerns are an intermittent ticking or clicking noise from the rear HVAC system, being unable to control the rear system temperature, and being unable to change the rear system modes.
    • Cause：The HVAC actuators may hunt for the correct commanded position, and this cycling can cause a clicking or ticking noise.
    • Cause：Overtravel of the HVAC system control doors can cause the listed conditions; when it occurs a DTC sets and the door goes to a preset default position.
    • Condition：A defaulted door stays at the default position until the code is cleared; clearing the code lets it operate properly until overtravel occurs again.
    • Confirm：The overtravel DTCs are B0434 for the auxiliary (rear) temperature door and B3764 for the auxiliary (rear) mode door.
    • Repair：Replace the auxiliary (rear) HVAC control module; it contains a new calibration that compensates for the actuator overtravel and the hunting, clicking and ticking noises.
    • Parts：For all 2003-06 with CJ2 and C69, the auxiliary HVAC control module is part number 15832319.
    • Caution：With the new module the rear blower speed may rise slightly (approximately 50 rpm); if the customer objects, the blower control module may be replaced with the second design blower control module.
    • Parts：The second design rear blower control module is 89024926 for Tahoe, Yukon and Escalade (short wheelbase) and 89018846 for Suburban, Yukon XL and Escalade ESV (long wheelbase).
    • Caution：Do not use the revised auxiliary HVAC control module unless one or more of the listed codes is set; it will not correct any other DTC or A/C performance concern.

    Open this issue of GM TechLink ↗ The points above are read from an article of TechLink, GM’s monthly publication for dealership technicians. The article itself is not reproduced here.

    Remedy
    Rear HVAC System Conditions Owners of some 2003-06 Cadillac Escalade, Chevrolet Suburban and Tahoe, and GMC Yukon models with RPO CJ2 and C69 may have one or more of the following concerns: - Intermittent ticking/clicking noise from rear HVAC system - Unable to control rear system temperature - Unable to change rear system modes The HVAC actuators may hunt for the correct commanded position. This cycling can cause a clicking or ticking noise. Overtravel of the HVAC system control doors can cause one or more of the listed system conditions. If overtravel occurs, a DTC sets and the door goes to a preset default position. When a system door defaults, that door stays at the default position until the code is cleared. Clearing the code allows the door to operate properly until the overtravel condition re-occurs. B0434 Auxiliary (rear) temperature door B3764 Auxiliary (rear) mode door Replace the auxiliary (rear) HVAC control module (part number listed in the table below). This module contains a new calibration to compensate for the actuator overtravel condition and the hunting/clicking and ticking noises. All 2003-06 with CJ2 and C69 Module, Auxiliary HVAC control 15832319 When using the new auxiliary HVAC control module, you may notice a slight increase in rear blower speed (approximately 50 rpm). If the customer comments that the increase in blower speed is objectionable, the blower control module may be replaced with the second design blower control module to correct the slight increase in blower speed. Tahoe, Yukon, Escalade (short wheelbase) Second design rear blower control module 89024926 Suburban, Yukon XL, Escalade ESV (long wheelbase) Second design rear blower control module 89018846 TIP: The revised auxiliary HVAC control module should not be used unless one or more of the codes listed above is set. The revised control module will not correct any other DTC or A/C performance concern.

EQUIPMENT7

  1. Manufacturer communication2003–2006 GMC YUKON DENALI ・ 2012-04-10

    Blower Motor Inoperativity with Key Off

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      BUICK/CADILLAC/CHEVROLET/GMC/OLDSMOBILE: IF BLOWER MOTOR IS SET TO ANY SPEED POSITION AND WHEN KEY IS OFF, IT BECOMES INOPERATIVE AND MAY STILL BE INOPERATIVE AFTER KEY IS TURNED ON. *PE UPDATED ON 5/1/12. *JS

    Read the sentences of the record
    Remedy
    BUICK/CADILLAC/CHEVROLET/GMC/OLDSMOBILE: IF BLOWER MOTOR IS SET TO ANY SPEED POSITION AND WHEN KEY IS OFF, IT BECOMES INOPERATIVE AND MAY STILL BE INOPERATIVE AFTER KEY IS TURNED ON. *PE UPDATED ON 5/1/12. *JS

  2. Manufacturer communication2004–2006 GMC YUKON ・ 2005-11-04

    Blower Motor Speed Loss Except High Speed or Inoperative

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      EI05082 - LOSS OF BLOWER MOTOR SPEEDS EXCEPT FOR HIGH SPEED OR INOPERATIVE. *TT UPDATED. *KB UPDATED *KB

    Read the sentences of the record
    Remedy
    EI05082 - LOSS OF BLOWER MOTOR SPEEDS EXCEPT FOR HIGH SPEED OR INOPERATIVE. *TT UPDATED. *KB UPDATED *KB

  3. Owner complaint2005 GMC YUKON DENALI ・ 2005-09-15

    A/C makes noise when compressor engages or switches

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

    Read the sentences of the record
    Fault
    THE A/C MAKES A NOISE WHEN THE COMPRESSOR ENGAGES OR SWITCHES. (1 more)
    Remedy
    THE DEALERSHIP REPLACED THE COMPRESSOR TO NO AVAIL.

  4. Manufacturer communication2003–2005 GMC YUKON ・ 2005-03-12

    HVAC Not Cold Enough: A/C Compressor Does Not Engage

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      HVAC NOT COLD ENOUGH A/C COMPRESSOR DOES NOT ENGAGE . *EH

    Read the sentences of the record
    Remedy
    HVAC NOT COLD ENOUGH A/C COMPRESSOR DOES NOT ENGAGE . *EH

  5. Manufacturer communication2003–2005 GMC YUKON ・ 2005-02-17

    HVAC Control Issue Notification

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      HEAT VENTILATION AND AIR CONDITIONING SYSTEM CANNOT BE CONTROLLED OR DEFAULTS TO DEFROST MODE. *EH

    Read the sentences of the record
    Remedy
    HEAT VENTILATION AND AIR CONDITIONING SYSTEM CANNOT BE CONTROLLED OR DEFAULTS TO DEFROST MODE. *EH

  6. Manufacturer communication2000–2005 GMC YUKON DENALI ・ 2005-01-10

    A/C Low Pressure Switch Diagnosis with Kent Moore Tool GE-47742

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      DIAGNOSTIC INFORMATION TO ACCURATELY DIAGNOSE A/C LOW PRESSURE SWITCH USING NEW KENT MOORE SPECIAL TOOL GE-47742. *TT

    Read the sentences of the record
    Remedy
    DIAGNOSTIC INFORMATION TO ACCURATELY DIAGNOSE A/C LOW PRESSURE SWITCH USING NEW KENT MOORE SPECIAL TOOL GE-47742. *TT

  7. Manufacturer communication2000–2005 GMC YUKON ・ 2004-10-04

    A/C Low Pressure Switch Diagnostic Tool Communication

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      AIR CONDITIONER (A/C) LOW PRESSURE SWITCH DIAGNOSTIC TOOL. CURRENTLY THE A/C LOW PRESSURE SWITCH OPEN/CLOSE PRESSURES CANNOT BE ACCURATELY DETERMINED BY MEASURING PRESSURE AT THE LOW SIDE SERVICE PORT. *TT

    Read the sentences of the record
    Remedy
    AIR CONDITIONER (A/C) LOW PRESSURE SWITCH DIAGNOSTIC TOOL. CURRENTLY THE A/C LOW PRESSURE SWITCH OPEN/CLOSE PRESSURES CANNOT BE ACCURATELY DETERMINED BY MEASURING PRESSURE AT THE LOW SIDE SERVICE PORT. *TT

VISIBILITY6

  1. Manufacturer communication2001–2006 GMC YUKON DENALI ・ 2017-12-22

    Rear Window Defroster Contact or Tabs Service Information

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      Repair

      1. On 2007-2014 Tahoe, Suburban, Yukon and Escalade with moveable glass always replace the defroster tab (GM P/N 25916031) and the power connector (P/N 12034110); on all other vehicles reconnect the original defroster tab.
      2. Remove the rear defroster power connector and crimp a new one to the feed wire; the proper connector, P/N 12034110, is in the Packard Electrical Assortment, Tray 18, Position 5.
      3. Prepare the surface of the used defroster tab and the defroster buss bar with fine grain (500 grit) sandpaper or Emery cloth.
      4. Wipe the prepared contact area with Kent Automotive Acrysol (or equivalent) to remove residual oil or dirt.
      5. Heat the new connector on the buss bar surface to be soldered, holding the connector and defroster tab in place with long nose pliers.

      Part numbers printed in the document

      The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

      Parts

      • Silver solder: Radio Shack (The Source in Canada) 64-013, 0.022" diameter.
      • Solvent: P20005 Kent Automotive Acrysol Solvent (32 fl oz) 946 ml.

      Caution

      • Let the glass warm to the temperature inside the building; soldering creates a hot spot in the glass, so do not solder on cold glass.
      • Heating the glass excessively, or repeatedly without time to cool, may break the glass.
      • A silver-bearing solder must be used; do not attempt the repair with conventional tin/lead alloy solders.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Covers 2000-2015 GM passenger cars and trucks, excluding the 2015 Chevrolet Tahoe, Suburban, GMC Yukon and Cadillac Escalade.
    • Applies to：Vehicles must have the electric rear window defroster (RPO C49).
    • Repair：On 2007-2014 Tahoe, Suburban, Yukon and Escalade with moveable glass always replace the defroster tab (GM P/N 25916031) and the power connector (P/N 12034110); on all other vehicles reconnect the original defroster tab.
    • Caution：Let the glass warm to the temperature inside the building; soldering creates a hot spot in the glass, so do not solder on cold glass.
    • Caution：Heating the glass excessively, or repeatedly without time to cool, may break the glass.
    • Caution：A silver-bearing solder must be used; do not attempt the repair with conventional tin/lead alloy solders.
    • Repair：Remove the rear defroster power connector and crimp a new one to the feed wire; the proper connector, P/N 12034110, is in the Packard Electrical Assortment, Tray 18, Position 5.
    • Repair：Prepare the surface of the used defroster tab and the defroster buss bar with fine grain (500 grit) sandpaper or Emery cloth.
    • Repair：Wipe the prepared contact area with Kent Automotive Acrysol (or equivalent) to remove residual oil or dirt.
    • Repair：Heat the new connector on the buss bar surface to be soldered, holding the connector and defroster tab in place with long nose pliers.
    • Parts：Silver solder: Radio Shack (The Source in Canada) 64-013, 0.022" diameter.
    • Parts：Solvent: P20005 Kent Automotive Acrysol Solvent (32 fl oz) 946 ml.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This informational bulletin provide information for the technicians to repair the rear window defroster contact or tabs.

  2. Manufacturer communication2003–2006 GMC YUKON ・ 2006-01-09

    Front HVAC Blower Inoperative

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      FRONT HVAC BLOWER INOPERATIVE. *TT

    Read the sentences of the record
    Remedy
    FRONT HVAC BLOWER INOPERATIVE. *TT

  3. Manufacturer communication2004–2006 GMC YUKON ・ 2006-01-06

    Front Blower Inoperative or Running During Low Ambient Temperature

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      FRONT BLOWER INOPERATIVE STAY RUNNING DURING LOW AMBIENT TEMPERATURE. *TT

    Read the sentences of the record
    Remedy
    FRONT BLOWER INOPERATIVE STAY RUNNING DURING LOW AMBIENT TEMPERATURE. *TT

  4. Manufacturer communication2004–2005 GMC YUKON ・ 2005-10-25

    Blower Motor Inoperative at Low Ambient Temperatures

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      BLOWER MOTOR INOPERATIVE AT LOW AMBIENT TEMPERATURES. *TT

    Read the sentences of the record
    Remedy
    BLOWER MOTOR INOPERATIVE AT LOW AMBIENT TEMPERATURES. *TT

  5. Manufacturer communication2003–2006 GMC YUKON ・ 2005-10-20

    Rear Blower Motor Operation Issue

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      REAR BLOWER TURNS ON BY ITSELF/DEFAULTS TO HIGH BLOWER SPEED AND/OR DEFAULTS TO FULL COLD. *TT

    Read the sentences of the record
    Remedy
    REAR BLOWER TURNS ON BY ITSELF/DEFAULTS TO HIGH BLOWER SPEED AND/OR DEFAULTS TO FULL COLD. *TT

  6. Manufacturer communication2003–2005 GMC YUKON ・ 2005-01-10

    HVAC Blower Motor Inoperative or Stays Running

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      HVAC BLOWER MOTOR INOPERATIVE OR STAYS RUNNING. *TT

    Read the sentences of the record
    Remedy
    HVAC BLOWER MOTOR INOPERATIVE OR STAYS RUNNING. *TT

ELECTRICAL SYSTEM2

  1. Owner complaint2005 GMC YUKON ・ 2015-06-16

    Smoke from air conditioner vents and cable fire under dashboard while driving

    1. 1Fault

    2. 2Finding the cause

    3. 3CorrectionNot repaired

      THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED.

    Read the sentences of the record
    Fault
    WHILE DRIVING AT APPROXIMATELY 55 MPH (= 88.5 km/h), THE CONTACT NOTICED SMOKE COMING FROM THE AIR CONDITIONER VENTS. (1 more)
    Remedy
    THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED.

  2. Manufacturer communication2005 GMC YUKON ・ 2004-12-29

    Driver Seat Adjuster Memory & Heater Switch Will Not Illuminate

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      DRIVER SEAT ADJUSTER MEMORY & HEATER SWITCH WILL NOT ILLUMINATE. *TT

    Read the sentences of the record
    Remedy
    DRIVER SEAT ADJUSTER MEMORY & HEATER SWITCH WILL NOT ILLUMINATE. *TT

AIR BAGS1

  1. Owner complaint2005 GMC YUKON DENALI ・ 2014-05-21

    Airbag light on and multiple electrical, mechanical and comfort issues since 2005

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

    Read the sentences of the record
    Fault
    AIRBAG LIGHT CONTINUOUSLY ON - READS, SERVICE AIRBAG. (13 more)
    Inspection
    I HAVE TAKEN IT IN FOR SERVICE SEVERAL TIMES BUT MIRACULOUSLY THE GMC SERVICE CENTER SAYS THE LIGHT DOESN'T COME ON WHEN THEY HAVE IT.

ENGINE1

  1. Owner complaint2005 GMC YUKON ・ 2022-01-18

    Blower motor control module continues to operate after vehicle shut off

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      The contact was able to drive the vehicle back home and had a mechanically inclined friend to disconnect the blower motor wiring harness. (1 more)

    Read the sentences of the record
    Fault
    The contact stated that after his wife turned off the vehicle, the blower motor control module continued to operate and would not shut off as needed.
    Remedy
    The contact was able to drive the vehicle back home and had a mechanically inclined friend to disconnect the blower motor wiring harness. (1 more)

ENGINE AND ENGINE COOLING1

  1. Manufacturer communication2004–2006 GMC YUKON ・ 2007-07-24

    Front Blower Motor Inoperative or Not Shutting Off in Low Temperature

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      FRONT BLOWER MOTOR INOPERATIVE OR MAY NOT SHUT OFF IN EXTREMELY LOW AMBIENT TEMPERATURE CONDITIONS. *KB

    Read the sentences of the record
    Remedy
    FRONT BLOWER MOTOR INOPERATIVE OR MAY NOT SHUT OFF IN EXTREMELY LOW AMBIENT TEMPERATURE CONDITIONS. *KB

UNKNOWN OR OTHER1

  1. Manufacturer communication2000–2006 GMC YUKON ・ 2024-09-12(8 earlier editions of this document folded here)

    Heater-Vent-Air Conditioning Warm Air Issue

    1. 1Fault

      • The A/C blows warm or A/C performance is poor.

    2. 2Finding the cause

      Steps to confirm (in the document’s order)

      1. Record the A/C high and low pressures from actual A/C gauges, the high side sensor reading from GDS, and the A/C compressor duty cycle.
      2. Also record the outside temperature, humidity and vent temperature.
      3. With an automatic HVAC system, read the evaporator temperature sensor (if equipped), inside temperature sensor, outside temperature sensor and duct temperature sensors with the scan tool.

    3. 3Correction

      This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to all models, 2000 - 2024.
    • Condition：The A/C blows warm or A/C performance is poor.
    • Confirm：Record the A/C high and low pressures from actual A/C gauges, the high side sensor reading from GDS, and the A/C compressor duty cycle.
    • Confirm：Also record the outside temperature, humidity and vent temperature.
    • Confirm：With an automatic HVAC system, read the evaporator temperature sensor (if equipped), inside temperature sensor, outside temperature sensor and duct temperature sensors with the scan tool.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

Showing 25 of the 33 you can open. Narrow the search to see the rest.