Skip to content
FaultCrate
日本語

This is an open preview: every record can be read without an account.

GMC Yukon 2000–2006

GMC YukonModel years 2000–2006

Change vehicle →
Clear the search
2 conditions added

The vehicle (where a record says)

A record is under an engine, a drive or a series only where it says so: the characters of the vehicle identification number filed with a complaint, its text, or what its document says it applies to. A record that does not say is kept as "not stated". The filed numbers and the documents do not tell 4WD from AWD.

Common on this vehicle:Gauge or instrument faultWarning lightNoiseLeakMisfire or rough idleAir conditioning or heaterCorrosion or rustVibration or shudder

Record by record

90 records state a cause or a remedy. Each record is shown as short labels in the order fault → finding the cause → correction. Press a label to narrow to the records that state it.

Symptom

Component named as the cause

Work done

How it is said to have ended

  • says it was fixed1
  • says it came back1
  • result not stated2

A ribbon is as wide as the records that state both of its ends (only the commonest are drawn). A record that names several symptoms or components runs through each. Orange is records that say the fault came back or was not fixed. Results come from owners’ reports only; one that does not say is “result not stated”. None of this is a likelihood of a cause or a rate at which work succeeds.

Read the records one by one (17)

Known issuesInstrument panel cluster gauges stick, flutter or stop working7

  1. Owner complaint2004 GMC YUKON DENALI ・ 2015-02-27

    Multiple electrical and mechanical failures including gauge failure, brake issues, and more

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      WHICH I HAD TO REPLACE. (1 more)

      What the documents say to do

      Instrument panel cluster gauges stick, flutter or stop working

      Repair

      • Dealers replace the instrument panel cluster after verifying the condition.
    Read the sentences of the record
    Fault
    IT'S LIKE IT STARTS SLOW YOUR GAUGES GO OUT. (2 more)
    Remedy
    WHICH I HAD TO REPLACE. (1 more)

  2. Owner complaint2004 GMC YUKON DENALI ・ 2015-05-14

    Speedometer failure in 2004 GMC Yukon Denali

    1. 1Fault

    2. 2Finding the cause

    3. 3CorrectionNot repaired

      THE VEHICLE WAS NOT REPAIRED.

      What the documents say to do

      Instrument panel cluster gauges stick, flutter or stop working

      Repair

      • Dealers replace the instrument panel cluster after verifying the condition.
    Read the sentences of the record
    Fault
    THE CONTACT STATED THAT THE SPEEDOMETER FAILED AND PREVENTED THE CONTACT FROM KNOWING HOW FAST THE VEHICLE WAS TRAVELING.
    Remedy
    THE VEHICLE WAS NOT REPAIRED.

  3. Owner complaint2004 GMC YUKON ・ 2015-05-04

    Instrument cluster gauges stop working intermittently

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

    Read the sentences of the record
    Fault
    MY HUSBAND EXPLAINED THE GAUGES WOULD SOMETIMES STICK/QUITE WORKING WHILE DRIVING THE VEHICLE AND SOMETIMES WHEN STARTING THE VEHICLE AND HE WOULD SOMETIMES HAVE TO TAP ON IT TO TRY TO GET IT TO WORK AGAIN.
    Cause
    THERE MUST BE A DEFECT IN THESE PANELS.
    Inspection
    MY HUSBAND CONTACTED THE DEALERSHIP AND WAS TOLD TO BRING THE VEHICLE IN TO ONE OF THEIR SERVICE CENTER WHICH THEY LOOKED AT IT AND STATED THEY COULDN'T FIND NOTHING WRONG WITH IT. (1 more)

  4. Owner complaint2004 GMC YUKON DENALI ・ 2011-05-04

    Instrument panel reading inaccurately

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3CorrectionNot repaired

      THE VEHICLE WAS NOT REPAIRED.

      What the documents say to do

      Instrument panel cluster gauges stick, flutter or stop working

      Repair

      • Dealers replace the instrument panel cluster after verifying the condition.
    Read the sentences of the record
    Fault
    THE CONTACT NOTICED THAT THE INSTRUMENT PANEL WAS READING INACCURATELY. (2 more)
    Remedy
    THE VEHICLE WAS NOT REPAIRED.

  5. Owner complaint2004 GMC YUKON ・ 2011-01-20

    Check engine light illuminates intermittently and speedometer sticks

    1. 1Fault

    2. 2Finding the cause

    3. 3CorrectionNot repaired

      THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED.

      What the documents say to do

      Instrument panel cluster gauges stick, flutter or stop working

      Repair

      • Dealers replace the instrument panel cluster after verifying the condition.
    Read the sentences of the record
    Fault
    WHILE PARKED, THE CONTACT STARTED THE IGNITION AND THE CHECK ENGINE LIGHT ILLUMINATED. (1 more)
    Remedy
    THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED.

  6. Owner complaint2004 GMC YUKON DENALI ・ 2010-08-12

    Speedometer displaying inaccurate reading

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3CorrectionNot repaired

      THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED WHEN THE COMPLAINT WAS FILED.

      What the documents say to do

      Instrument panel cluster gauges stick, flutter or stop working

      Repair

      • Dealers replace the instrument panel cluster after verifying the condition.
    Read the sentences of the record
    Fault
    WHILE DRIVING AT AN UNKNOWN SPEED, THE CONTACT OBSERVED THAT THE SPEEDOMETER DISPLAYED AN INACCURATE READING. (1 more)
    Remedy
    THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED WHEN THE COMPLAINT WAS FILED.

  7. Owner complaint2004 GMC YUKON DENALI ・ 2010-02-03

    Malfunctioning speedometer showing 30 MPH over actual speed during normal driving

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3CorrectionNot repaired

      NO REPAIRS COMPLETED. *TR

      What the documents say to do

      Instrument panel cluster gauges stick, flutter or stop working

      Repair

      • Dealers replace the instrument panel cluster after verifying the condition.
    Read the sentences of the record
    Fault
    NORMAL DRIVING CONDITIONS. (1 more)
    Remedy
    NO REPAIRS COMPLETED. *TR

Known issuesFuel gauge reads low or drops to empty in Park / Neutral (normal characteristic)1

  1. Manufacturer communication2000–2006 GMC YUKON DENALI ・ 2017-08-15

    Fuel Gauge Accuracy—Preliminary Information

    1. 1Fault

      • The fuel gauge may be inaccurate or drop to empty (E) with the low fuel light coming on.
      • The condition is most apparent when the gauge is at or below the quarter (1/4) tank mark.

    2. 2Finding the cause

      Possible causes

      • On an automatic transmission no buffering of the fuel gauge takes place when the transmission is in park or neutral.

      Steps to confirm (in the document’s order)

      1. Try to duplicate it by driving a short distance in reverse and stopping (to make fuel slosh), shifting to park or neutral and then to drive.
      2. Note how the vehicle is being parked (on an incline, front of the vehicle up hill or down hill).

    3. 3Correction

      Caution

      • This is a normal characteristic and no repairs are necessary.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：The model list names 2000-2015 GMC Yukon models.
    • Condition：The fuel gauge may be inaccurate or drop to empty (E) with the low fuel light coming on.
    • Condition：The condition is most apparent when the gauge is at or below the quarter (1/4) tank mark.
    • Confirm：Try to duplicate it by driving a short distance in reverse and stopping (to make fuel slosh), shifting to park or neutral and then to drive.
    • Confirm：Note how the vehicle is being parked (on an incline, front of the vehicle up hill or down hill).
    • Cause：On an automatic transmission no buffering of the fuel gauge takes place when the transmission is in park or neutral.
    • Caution：This is a normal characteristic and no repairs are necessary.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This Preliminary Information communication provides information to the technician about vehicles that have an inaccurate fuel gauge. Technician should drive the vehicle to duplicate the concern. The fuel gauge will have a tendency to falsely indicate a lower fuel level than what is actually present. The fuel gauge will take a few minutes to show the correct fuel level. On vehicles equipped with an automatic transmission no buffering takes place when the transmission is in park or neutral. This is a normal characteristic and no repairs are necessary. On vehicles equipped with a manual transmission the fuel gauge is buffered in all gears and neutral. There is a timer which starts to count up when the clutch is depressed. When this timer reaches its calibrated value the buffering stops. This is a normal characteristic and no repairs are necessary.

Known issuesSpeedometer needle appears inaccurate (specification +/- 2 MPH)1

  1. Manufacturer communication2003–2006 GMC YUKON ・ 2024-08-13(11 earlier editions of this document folded here)

    Speedometer Needle Accuracy Preliminary Information

    1. 1Fault

      • A customer may say the speedometer needle appears inaccurate.

    2. 2Finding the cause

      Possible causes

      • An instrument panel cluster with a physical speedometer needle drives the needle electrically with a stepper motor, and some variation in accuracy is possible.

      Steps to confirm (in the document’s order)

      1. Digital readouts such as the "Digital Speedometer" on the DIC read the Vehicle Speed Sensor (VSS) directly and are much more accurate.
      2. The specification for needle accuracy is +/- 2 MPH (= 3.22 km/h) at any given speed when looking straight at the needle.

    3. 3Correction

      This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH (= 3.22 km/h) at any given speed when looking straight at the needle. Â

      What the documents say to do

      Speedometer needle appears inaccurate (specification +/- 2 MPH)

      Confirm

      • The needle accuracy specification is +/- 2 MPH (= 3.22 km/h) at any given speed when looking straight at the needle.

      Caution

      • Tire size, tread life and inflation may cause some variation in the readings.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to 2003 - 2024 GMC Yukon models (note: the years run later than the years this service covers).
    • Condition：A customer may say the speedometer needle appears inaccurate.
    • Cause：An instrument panel cluster with a physical speedometer needle drives the needle electrically with a stepper motor, and some variation in accuracy is possible.
    • Confirm：Digital readouts such as the "Digital Speedometer" on the DIC read the Vehicle Speed Sensor (VSS) directly and are much more accurate.
    • Confirm：The specification for needle accuracy is +/- 2 MPH (= 3.22 km/h) at any given speed when looking straight at the needle.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH (= 3.22 km/h) at any given speed when looking straight at the needle. Â

ELECTRICAL SYSTEM6

  1. Manufacturer communication2003–2006 GMC YUKON DENALI ・ 2023-10-18(6 earlier editions of this document folded here)

    IPC odometer programming method notification

    1. 1Fault

      • It is a reference guide for identifying which odometer programming method to use after replacing the instrument panel cluster (IPC).

    2. 2Finding the cause

      Not stated

    3. 3Correction

      Repair

      1. The table lists the 2003-2006 Yukon with the odometer value stored in the IPC and SPS as the programming method.
      2. The SPS method is IPC reprogramming and setup using the service programming system (SPS).

      Caution

      • Vehicles not listed in the document need to follow the SPS Programming for Odometer.
      • Stable battery voltage is critical during programming; any fluctuation, spiking, over voltage or loss of voltage will interrupt it.
      • Install the EL-49642 SPS Programming Support Tool (GM Dealer Equipment Item #PSC-550) to maintain system voltage; if not available, connect a fully charged 12V jumper or booster pack disconnected from the AC supply, and do not connect a battery charger.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：The bulletin is addressed to 2020 and prior GM passenger cars and trucks sold in the U.S. and Canada only.
    • Condition：It is a reference guide for identifying which odometer programming method to use after replacing the instrument panel cluster (IPC).
    • Repair：The table lists the 2003-2006 Yukon with the odometer value stored in the IPC and SPS as the programming method.
    • Repair：The SPS method is IPC reprogramming and setup using the service programming system (SPS).
    • Caution：Vehicles not listed in the document need to follow the SPS Programming for Odometer.
    • Caution：Stable battery voltage is critical during programming; any fluctuation, spiking, over voltage or loss of voltage will interrupt it.
    • Caution：Install the EL-49642 SPS Programming Support Tool (GM Dealer Equipment Item #PSC-550) to maintain system voltage; if not available, connect a fully charged 12V jumper or booster pack disconnected from the AC supply, and do not connect a battery charger.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This informational bulletin provides information for the IPC odometer programming method quick reference guide.

  2. Manufacturer communication2003–2006 GMC YUKON ・ 2021-04-20

    IPC Odometer Programming Method Quick Reference Guide

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

    Read the sentences of the record
    Remedy
    IPC Odometer Programming Method Quick Reference Guide Season Odometer Programming Methods in Use Today 1. IPC reprogramming and setup using the service programming system (SPS). 2. Odometer setup at the electronic service center (ESC) when using an exchange IPC/DIC. 3. Tech 2® – The Tech 2 is used to set up a replacement BCM, which includes loading the odometer value that is displayed and stored in the IPC. A replacement IPC will display the previously stored vehicle odometer value, communicated from the BCM, after cycling the ignition or driving the vehicle. *The odometer programming is integrated as part of the BCM programming procedure. It is not a stand-alone event.

  3. Manufacturer communication2003–2006 GMC YUKON DENALI ・ 2021-04-16

    IPC Odometer Programming Method Quick Reference

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      IPC Odometer Programming Method Quick Reference Guide

    Read the sentences of the record
    Remedy
    IPC Odometer Programming Method Quick Reference Guide

  4. Manufacturer communication2000–2006 GMC YUKON DENALI ・ 2017-12-14(1 earlier editions of this document folded here)

    Inaccurate Odometer Reading – Preliminary Information

    1. 1Fault

      • A customer may say the odometer appears inaccurate compared with a known distance traveled.

    2. 2Finding the cause

      Steps to confirm (in the document’s order)

      1. Use a hand-held GPS unit to test the odometer.
      2. On a straight road over a mile long, mark the GPS waypoint when the odometer (not the trip odometer) rolls over a digit.
      3. Confirm that the original size tires and wheels are mounted and that the axle ratio is as specified on the SPID label and unmodified.
      4. If those are correct and the odometer is beyond the limit, consider the relationship between the VSS and the reluctor on the transmission output shaft.
      5. Closely inspect the associated wiring and any connectors in the circuits.

    3. 3Correction

      Repair

      • Finally, it may be necessary to exchange the IPC with a replacement unit.

      Caution

      • Generally a tolerance of plus or minus 4% is allowed.
      • Do not compare with another vehicle or with the trip odometer.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to all brands and models, model years 2000 - 2018.
    • Condition：A customer may say the odometer appears inaccurate compared with a known distance traveled.
    • Caution：Generally a tolerance of plus or minus 4% is allowed.
    • Confirm：Use a hand-held GPS unit to test the odometer.
    • Confirm：On a straight road over a mile long, mark the GPS waypoint when the odometer (not the trip odometer) rolls over a digit.
    • Caution：Do not compare with another vehicle or with the trip odometer.
    • Confirm：Confirm that the original size tires and wheels are mounted and that the axle ratio is as specified on the SPID label and unmodified.
    • Confirm：If those are correct and the odometer is beyond the limit, consider the relationship between the VSS and the reluctor on the transmission output shaft.
    • Confirm：Closely inspect the associated wiring and any connectors in the circuits.
    • Repair：Finally, it may be necessary to exchange the IPC with a replacement unit.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.

  5. Manufacturer communication2000–2006 GMC YUKON DENALI ・ 2017-08-15

    Instrument Panel Cluster Mileage Programming Information

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      Repair

      • When the odometer cannot be set to the actual vehicle mileage, it must be set at zero and a label affixed to the driver's door frame by the service agent.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to 2014 and prior GM passenger cars and trucks.
    • Repair：When the odometer cannot be set to the actual vehicle mileage, it must be set at zero and a label affixed to the driver's door frame by the service agent.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This Preliminary Information communication provides information to the technician that after replacing the Instrument Panel Cluster the exchange center is unable to program the actual mileage on the odometer or the actual mileage is unknown. Dealer will need to follow dealer to the General Motors service policies and procedures manual section 3.2.4 odometer servicing.

  6. Manufacturer communication2003–2004 GMC YUKON ・ 2008-11-06

    Instrument Panel Gauge Needles Condition

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      CADILLAC CHEVROLET GMC SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. SOME VEHICLES COULD DEVELOP A CONDITION WHERE ONE OR MORE OF THE INSTRUMENT PANEL GAUGE NEEDLES MAY STICK, FLUTTER, OR BECOME INOPERATIVE. CSC LETTER RECEIVED. UPDATED 11/6/08. *PE

    Read the sentences of the record
    Remedy
    CADILLAC CHEVROLET GMC SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. SOME VEHICLES COULD DEVELOP A CONDITION WHERE ONE OR MORE OF THE INSTRUMENT PANEL GAUGE NEEDLES MAY STICK, FLUTTER, OR BECOME INOPERATIVE. CSC LETTER RECEIVED. UPDATED 11/6/08. *PE

ENGINE AND ENGINE COOLING1

  1. Manufacturer communication2000–2006 GMC YUKON DENALI ・ 2017-08-15(1 earlier editions of this document folded here)

    Engine Check Lamp P0442 Evaporative Emissions System Notification

    1. 1Fault

      • The service engine soon lamp (MIL) is on for DTC P0442, but a leak cannot be verified with the system test in the service information.

    2. 2Finding the cause

      Steps to confirm (in the document’s order)

      1. With the scan tool, command the EVAP system CLOSED, start the engine and watch the tank pressure sensor value for about two minutes.
      2. If the tank pressure value changes (shows vacuum), remove the purge solenoid and pressurize its fuel tank side with the GE 41413-A / J 41413-A tester.
      3. If the tank pressure value does not change, install the CH-48096 adaptor between the purge line from the canister and the purge solenoid; use no other adaptor or pressurization method.
      4. With the EVAP system CLOSED, pressurize through the adaptor and let the system stabilize, watching the gauge for at least 5 minutes, then add smoke.
      5. Look for smoke or UV trace fluid at the purge solenoid, the engine side, the fuel cap or capless fill door, and the canister vent solenoid filter or fresh-air line.
      1 more points

    3. 3Correction

      Repair

      • If smoke passes through the purge solenoid, replace the purge solenoid.

      Caution

      • After verifying P0442, do not disturb any fuel system component before testing.
      • Test pressure must not exceed 13 in H2O (0.5 PSI (= 3.45 kPa)); more can make components perform inaccurately and lead to misdiagnosis.
      • A large temperature difference between vehicle, shop and tester seriously affects accuracy; let the vehicle adjust to shop temperature first.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to 2016 and prior passenger cars and trucks.
    • Condition：The service engine soon lamp (MIL) is on for DTC P0442, but a leak cannot be verified with the system test in the service information.
    • Caution：After verifying P0442, do not disturb any fuel system component before testing.
    • Confirm：With the scan tool, command the EVAP system CLOSED, start the engine and watch the tank pressure sensor value for about two minutes.
    • Confirm：If the tank pressure value changes (shows vacuum), remove the purge solenoid and pressurize its fuel tank side with the GE 41413-A / J 41413-A tester.
    • Repair：If smoke passes through the purge solenoid, replace the purge solenoid.
    • Confirm：If the tank pressure value does not change, install the CH-48096 adaptor between the purge line from the canister and the purge solenoid; use no other adaptor or pressurization method.
    • Confirm：With the EVAP system CLOSED, pressurize through the adaptor and let the system stabilize, watching the gauge for at least 5 minutes, then add smoke.
    • Confirm：Look for smoke or UV trace fluid at the purge solenoid, the engine side, the fuel cap or capless fill door, and the canister vent solenoid filter or fresh-air line.
    • Confirm：If smoke testing finds nothing, the leak may exist only under vacuum: use the scan tool Purge/Seal function to pull a vacuum and watch the FTP sensor parameter for vacuum decay.
    • Caution：Test pressure must not exceed 13 in H2O (0.5 PSI (= 3.45 kPa)); more can make components perform inaccurately and lead to misdiagnosis.
    • Caution：A large temperature difference between vehicle, shop and tester seriously affects accuracy; let the vehicle adjust to shop temperature first.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.

FUEL SYSTEM, OTHER1

  1. Manufacturer communication2000–2005 GMC YUKON ・ 2008-12-05

    GMC: Fuel Gauge Fluctuation in Park or Neutral

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      GMC: FUEL GAUGE FLUCTUATION IN PARK OR NEUTRAL, CAUSING THE LOW FUEL LIGHT TO ILLUMINATE. *PE

    Read the sentences of the record
    Remedy
    GMC: FUEL GAUGE FLUCTUATION IN PARK OR NEUTRAL, CAUSING THE LOW FUEL LIGHT TO ILLUMINATE. *PE

Showing 17 of the 90 you can open. Narrow the search to see the rest.

4 owner complaints have no classified sentences yet, so their causes and repairs are not picked out. Their text is in the list of records.