GMC Yukon 2000–2006
Common on this vehicle:Warning lightNoiseLeakGauge or instrument faultMisfire or rough idleVibration or shudderCorrosion or rustAir conditioning or heater
Possible causes
2005990 records
Instruments and lighting
Brakes
Exhaust and emissions
Engine
Steering
Electrical, wiring and power
26106411052111105117541141113222261 causes not drawn
- Cosmetic brake rotor corrosion: burnish, do not resurface1
- Stability System Disabled message and unwanted StabiliTrak activation (tire wear or mismatched tires)1
- ABS lamp with DTC C0265 (EBCM motor relay circuit) after EBCM replacement1
- Intake manifold gasket leak (cold idle misfire, lean codes)1
- P0300 after engine repairs: injector connectors crossed (cylinders 5-7 / 6-8)1
- Slight roughness at idle with no DTCs (possible characteristic)1
- Intermittent MIL, service lamps/messages or DTCs from connector fretting corrosion1
- Memory seat recalls to a more-forward position than set (memory seat module software)1
- Navigation radio returned from the Electronic Service Center: no navigation and CD ERROR message1
- Radio shows a disc error when a media disc is inserted (unsupported disc format or damaged disc)1
- Red radio theft LED does not flash (manufacturer's counter not reset at assembly)1
- DRLs or auto headlamps will not disable with the headlamp switch (Canada, RPO Z49; normal)1
- Hum or fan noise from the navigation radio (internal cooling fan, normal)1
- Autoride (Z55) Service Ride Control / Service Suspension System message3
- Vehicle body tilt or lean left / right (torsion bar front suspension)3
- Wheel: corroded3
- Aluminum Wheel Bead Seat: corroded2
- Aftermarket part (not the vehicle as built): Federal-Mogul National / Carquest replacement wheel hub assembly retention nut - recall 07E-1062WD only1
- Grease seen at front hub bearing seals (normal purge, do not replace)1
- Creak or squeak noise from the rear lower control arm bushings (do not replace the propshaft)1
- Upper control arm bracket alignment (dowel) pin missing at front end alignment1
- OnStar System: software, failed3
- OnStar cannot configure the vehicle (118 error) after the 15-08-44-001 upgrade2
- Some OnStar features no longer work (2G cellular sunset; the module is not broken)2
- Red OnStar LED and DTC B2455 after Canada upgrade bulletin 15-08-44-001 (audio and microphone drain wires shorted)1
- Digital Radio Receiver: failed1
- CD Player: failed, software2
- OnStar Hardware: software1
- HVAC blower motor resistor module / connector overheating3
- No passenger compartment air filter (not available from the 2003 model year; normal)2
- HVAC actuator clicking / ticking noises (recalibrate the HVAC control module, do not replace actuators)1
- Rear HVAC ticking noise, no rear temperature or mode control, DTC B0434 / B3764 (revised auxiliary HVAC control module)1
- Seat Heater: overheated3
- Out of fuel with the gauge reading above empty, cranks but no start, stall (replace the fuel sensor, not the sender module)2
- Engine fuel rail crossover tube retainer screws may break (5.3L RPO L59) - recall 04V-3765.3L only2
- Aftermarket part (not the vehicle as built): Fram G3727 replacement fuel filter connector - recall 06E-0431
- Fuel gauge reads low or drops to empty in Park / Neutral (normal characteristic)1
- Fuel Line: corroded, leaking3
- Seat Belt Buckle: failed, clogged or contaminated3
- 2nd row center seat belt routing (lap belt fit) - recall 05V-1631
- SIR lamp on and inside mirror temperature/compass display inoperative (open air bag fuse, circuit 1139 shorted to ground)1
- Air bag (SIR) lamp on with DTC B1001 after BCM or SDM replacement1
- Seat Belt Warning Light: failed1
- Headliner sagging (hook and loop patch detached; reattach with epoxy)2
- Power Folding Mirror: failed2
- Bench seat (RPO AE7) center console armrest hinges broken (replace the lid, not the console assembly)1
- Center console cupholder and ashtray lid will not close (Denali; latch pulled out of its retainer)1
- Door sags or is hard to open or close (worn or corroded hinge pins and bushings)1
- Snap or popping noise from the front of the vehicle (slot the front crossmember mounting holes)1
- Front seat adjuster switch knob loose or missing (replace only the switch cover)1
- Stains on the rear bumper step pad (treat with Armor-Dillo, do not replace)1
- Double vision or ghost image in the driver's auto dimming outside mirror (normal)1
- 4L60-E burnt 3-4 clutch pack1
- 4L60-E slip or no forward engagement right after input housing replacement (service part 17803687)1
- 4L80-E / 4L85-E planetary gear whine in first and second gear1
- Electronic transfer case stops shifting with no DTC (shift abuse lock out mode, normal)1
- Transfer case speed sensor connector locks bend on disconnect (improved connector)1
- 4L60-E / 4L65-E clunk on 2-3 upshift or 3-2 downshift (normal condition)1
- Grind / ratchet noise when shifting into Park in 4LO (characteristic)1
- Coolant leak at the rear of the vehicle (auxiliary heater hose quick connector)1
- Bolt: broken1
Causes with no correction stated (34)
Causes the records name for which no check or repair is stated, in a technical document or in a record. Press one for the records that name it.
- Exhaust and emissions
- Exhaust Manifold Bolt: broken (5)
- Suspension, wheels and tires
- Tire: worn, broken (4)Automatic Level Control: clogged or contaminated (1)
- Heating and air conditioning
- HVAC temperature doors default to full hot or defrost cannot be obtained (3)Air Conditioning Compressor: failed (1)Air Conditioning Low Pressure Switch: design or manufacturing (1)Blower Motor Control Module: failed (1)
- Fuel system
- Fuel Pump Module: corroded (3)Front Pump: leaking (1)Fuel Injector Inlet Filter: corroded (1)
- Body, doors and interior
- Liftgate Glass Hinge: broken, failed (3)Sunroof: failed (3)Door Glass: failed, loose or misadjusted (2)Outside Rearview Mirror: design or manufacturing (2)
- Transmission and driveline
- Transmission: clogged or contaminated, failed (3)Locking Rear Differential (2)Torque Converter Clutch: clogged or contaminated, failed (2)Transfer Case: failed (2)Transmission Oil Cooler Line: corroded (2)Axle Differential Seal: leaking (1)
- Electrical, wiring and power
- Intermittent no start with Service Stability, ABS light, 'Unknown Driver' and multiple DTCs / no module communication (2)Fuse: failed (2)Cable: overheated (1)Horn: failed (1)Powertrain Control Module: software (1)
- Brakes
- Service Stability message with DTC C0131, C0196, C0290 and/or C0292 (2)ABS Modulator Valve: corroded (1)Electronic Brake Control Module: software (1)Parking Brake: broken (1)
- Airbags and seat belts
- Airbag Sensor: failed (2)
- Instruments and lighting
- Ambient Light Sensor: loose or misadjusted (1)
- Audio and telematics
- CD Changer: failed (1)
The documents say what to doOnly records name itThe size of a node, the width of a link and the numbers are records matching this search, not likelihoods.
FaultCrate・GMC Yukon 2000–2006・2005
Candidate cause (the documents say what to do)
Stability System Disabled / Service Stability message with DTC C0455 (bent terminals at the steering wheel position sensor)
Owners may comment on a Stability System Disabled or Service Stability message with DTC C0455.
The concern may be caused by bent terminals on the SWPS (Steering Wheel Position Sensor).
How to tell
C0455Stability control message (StabiliTrak)
What to do
- Remove the SWPS connector and inspect for bent terminals.
- In most cases the terminals can be straightened without replacing the sensor.
What is needed
- Parts and materials
- Not stated
- Labor time
- Not stated
- Special tools
- Not stated
- Scan tool
- Not stated
Only what the technical documents state. "Not stated" does not mean not needed.
In the records
No record states work done for this cause.
See the evidence (1 technical documents, 1 records)
Passages of the technical documents
Applies to 2005 Cadillac, Chevrolet and GMC Full Size Utilities with RPO JL4.
This information applies to 2005 Cadillac, Chevrolet, and GMC Full Size Utilities with RPO JL4.
General Motors 2005-07-01
Owners may comment on a Stability System Disabled or Service Stability message with DTC C0455.
Owners may comment on a Stability System Disabled or Service Stability message with DTC C0455.
General Motors 2005-07-01
The concern may be caused by bent terminals on the SWPS (Steering Wheel Position Sensor).
This concern may be caused by bent terminals on the SWPS (Steering Wheel Position Sensor).
General Motors 2005-07-01
Remove the SWPS connector and inspect for bent terminals.
Remove the SWPS connector and inspect for bent terminals.
General Motors 2005-07-01
A cause or a result a complaint states is the owner’s view or what a dealer told them, not an established fact.
Put together by FaultCrate from public records and technical documents. The cause and the repair are for the workshop to decide with the vehicle in front of it. Counts are records, not failure rates.