GMC Yukon 2000–2006
Common on this vehicle:Warning lightLeakNoiseVibration or shudderMisfire or rough idleGauge or instrument faultAir conditioning or heaterCorrosion or rust
Possible causes
47 causes not drawn
- Intake manifold gasket leak (cold idle misfire, lean codes)1
- P0300 after engine repairs: injector connectors crossed (cylinders 5-7 / 6-8)1
- Slight roughness at idle with no DTCs (possible characteristic)1
- Throttle body carbon build-up: idle surge, reduced engine power, throttle DTCs (high mileage)1
- Stability System Disabled message and unwanted StabiliTrak activation (tire wear or mismatched tires)1
- OnStar Module: electrical fault1
- Aftermarket part (not the vehicle as built): Federal-Mogul National / Carquest replacement wheel hub assembly retention nut - recall 07E-1062WD only1
- Grease seen at front hub bearing seals (normal purge, do not replace)1
- Creak or squeak noise from the rear lower control arm bushings (do not replace the propshaft)1
- Upper control arm bracket alignment (dowel) pin missing at front end alignment1
- Ground Ring Terminal: loose or misadjusted3
- Intermittent stall, misfire or crank no start (Ignition 1 feed wire broken near C148/C149)2
- Vehicle Communication Interface Module: electrical fault, software2
- Intermittent MIL, service lamps/messages or DTCs from connector fretting corrosion1
- Navigation radio returned from the Electronic Service Center: no navigation and CD ERROR message1
- No crank with a blown Ign A fuse (circuit 142 pinched at the steering column support bracket)1
- Radio shows a disc error when a media disc is inserted (unsupported disc format or damaged disc)1
- DRLs or auto headlamps will not disable with the headlamp switch (Canada, RPO Z49; normal)1
- Steering intermediate shaft clunk3
- Power steering pump whine between idle and 2000 rpm1
- Headliner sagging (hook and loop patch detached; reattach with epoxy)2
- Power Folding Mirror: failed2
- Bench seat (RPO AE7) center console armrest hinges broken (replace the lid, not the console assembly)1
- Door sags or is hard to open or close (worn or corroded hinge pins and bushings)1
- Front seat adjuster switch knob loose or missing (replace only the switch cover)1
- Double vision or ghost image in the driver's auto dimming outside mirror (normal)1
- Mirror Glass: broken, loose or misadjusted2
- Sunroof: failed2
- HVAC blower motor resistor module / connector overheating2
- No passenger compartment air filter (not available from the 2003 model year; normal)2
- HVAC actuator clicking / ticking noises (recalibrate the HVAC control module, do not replace actuators)1
- Rear HVAC ticking noise, no rear temperature or mode control, DTC B0434 / B3764 (revised auxiliary HVAC control module)1
- Climate Control Module: software1
- Seat Belt Buckle: clogged or contaminated, failed2
- SIR lamp on and inside mirror temperature/compass display inoperative (open air bag fuse, circuit 1139 shorted to ground)1
- Air bag (SIR) lamp on with DTC B1001 after BCM or SDM replacement1
- Seat Belt Warning Light: failed1
- 4L60-E burnt 3-4 clutch pack1
- 4L60-E slip or no forward engagement right after input housing replacement (service part 17803687)1
- 4L80-E / 4L85-E planetary gear whine in first and second gear1
- Electronic transfer case stops shifting with no DTC (shift abuse lock out mode, normal)1
- Transfer case speed sensor connector locks bend on disconnect (improved connector)1
- 4L60-E / 4L65-E clunk on 2-3 upshift or 3-2 downshift (normal condition)1
- Grind / ratchet noise when shifting into Park in 4LO (characteristic)1
- Coolant leak at the rear of the vehicle (auxiliary heater hose quick connector)1
- Fuel gauge reads low or drops to empty in Park / Neutral (normal characteristic)1
- Tire and loading information label lists inaccurate vehicle capacity weight (FMVSS 110) - recall 05V-5521
Causes with no correction stated (18)
Causes the records name for which no check or repair is stated, in a technical document or in a record. Press one for the records that name it.
- Electrical, wiring and power
- Fuse: failed, electrical fault (4)Intermittent no start with Service Stability, ABS light, 'Unknown Driver' and multiple DTCs / no module communication (2)Cable: overheated (1)Powertrain Control Module: software (1)
- Transmission and driveline
- Transmission: failed, clogged or contaminated (3)Rear Axle: failed (2)Axle Differential Seal: leaking (1)Locking Rear Differential (1)
- Airbags and seat belts
- Airbag: failed (2)
- Other
- Bolt: broken (2)
- Body, doors and interior
- Locking Mechanism: design or manufacturing, failed (2)Camper Mirror: design or manufacturing (1)
- Heating and air conditioning
- HVAC temperature doors default to full hot or defrost cannot be obtained (1)
- Brakes
- Service Stability message with DTC C0131, C0196, C0290 and/or C0292 (1)Electronic Brake Control Module: software (1)Wheel Speed Sensor: corroded (1)
- Audio and telematics
- CD Changer: failed (1)
- Exhaust and emissions
- Exhaust Manifold Bolt: broken (1)
The documents say what to doOnly records name itThe size of a node, the width of a link and the numbers are records matching this search, not likelihoods.
FaultCrate・GMC Yukon 2000–2006・2006
Candidate cause (the documents say what to do)
Autoride (Z55) Service Ride Control / Service Suspension System message
On 2009 or earlier vehicles a Service Suspension System message may appear and the rear ride height may be incorrect.
The Electronic Suspension Control module will have DTC C0696 or C0711 set.
How to tell
C0580C0696C0711Service Ride Control / suspension message
What to do
- The compressor assembly may need to be removed to see whether the wiring is pinched between the compressor and the frame.
- The module checks level-system pressure at start-up and runs the compressor to add air to the shocks if it is below 10 psi (69 kPa).
- Repair the damaged or shorted circuits and reposition the wiring so it is not damaged again when the compressor is installed.
- The sensor is not serviced separately; install a complete air filter, dryer and sensor assembly.
- For a Service Ride Control message with DTC C0580, replace the right front shock absorber solenoid connector and install new A/C suction and auxiliary evaporator hoses.
- The jumper harness is included with the complete air filter, dryer, and sensor assembly PN 22964558; vehicles built in May, 2012 and later do not require the jumper harness and use PN 22941807.
Caution: Do not replace the complete air compressor assembly for this concern.
What is needed
- Parts and materials
- Air filter, dryer and sensor assembly PN 22964558 (includes the jumper harness)
- Right front shock absorber solenoid connector (for a Service Ride Control message with C0580)
- New A/C suction and auxiliary evaporator hoses (for a Service Ride Control message with C0580)
- Auto leveling compressor air inlet filter and hose assembly PN 22197160 (for condition 3)
Part numbers printed in the document
22964558Filter Assembly, Auto Level Control Air CompressorLook up at RockAuto (aftermarket candidates) ↗Search the web ↗
Discontinued (no successor stated)(replaces 20982305 / 22197161)as stated by GMPartsGiant (checked 2026-10-06) ↗
22941807Filter Assembly, Auto Level Control Air CompressorLook up at RockAuto (aftermarket candidates) ↗Search the web ↗
Discontinued (no successor stated)as stated by GMPartsGiant (checked 2026-10-06) ↗
22197160Look up at RockAuto (aftermarket candidates) ↗Search the web ↗
The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.
- Labor time
- Not stated
- Special tools
- Not stated
- Scan tool
- Not stated
Only what the technical documents state. "Not stated" does not mean not needed.
In the records
- Air Compressor: repaired 1
- Air Filter Dryer and Sensor Assembly: replaced 1
- Auto Leveling Compressor Air Inlet Filter and Hose Assembly: replaced 1
See the evidence (1 technical documents, 3 records)
Passages of the technical documents
The GM preliminary information covers 2001-2013 GMC Yukon, Yukon XL, Yukon Denali and Yukon Denali XL with RPO Z55 or Z95.
2001-2013 GMC Yukon, Yukon XL LD, Yukon Denali, Yukon Denali XL With RPO Z55 or Z95
General Motors (filed with NHTSA as SB-10052488) 2013-06-01
On 2009 or earlier vehicles a Service Suspension System message may appear and the rear ride height may be incorrect.
Some customers of 2009 or prior vehicles, may comment of a Service Suspension System message on the DIC and the rear suspension ride height is incorrect.
General Motors (filed with NHTSA as SB-10052488) 2013-06-01
The Electronic Suspension Control module will have DTC C0696 or C0711 set.
When checking for DTCs the Electronic Suspension Control (ESC) module will have DTC C0696 or C0711 set.
General Motors (filed with NHTSA as SB-10052488) 2013-06-01
The cause can be the automatic level control pressure sensor wiring shorted to ground.
This concern could be caused by the wiring to the automatic level control (ALC) pressure sensor being shorted to ground, as shown below.
General Motors (filed with NHTSA as SB-10052488) 2013-06-01
A cause or a result a complaint states is the owner’s view or what a dealer told them, not an established fact.
Put together by FaultCrate from public records and technical documents. The cause and the repair are for the workshop to decide with the vehicle in front of it. Counts are records, not failure rates.