Skip to content
FaultCrate
日本語

This is an open preview: every record can be read without an account.

GMC Yukon 2000–2006

GMC YukonModel years 2000–2006

Change vehicle →
Clear the search
Add conditions (optional: symptom, model year, system, warning display, trouble code, kind of record)

Common on this vehicle:Gauge or instrument faultLights (headlights, turn signals)NoiseWarning light

issueRecords under no cardRemoveremedyInstrument Panel ClusterRemove

Record by record

3 records state a cause or a remedy. Each record is shown as short labels in the order fault → finding the cause → correction. Press a label to narrow to the records that state it.

Symptom

Component named as the cause

Work done

How it is said to have ended

  • says it did not fix it3

A ribbon is as wide as the records that state both of its ends (only the commonest are drawn). A record that names several symptoms or components runs through each. Orange is records that say the fault came back or was not fixed. Results come from owners’ reports only; one that does not say is “result not stated”. None of this is a likelihood of a cause or a rate at which work succeeds.

Read the records one by one (3)

ELECTRICAL SYSTEM3

  1. Manufacturer communication2003–2006 GMC YUKON ・ 2021-04-20

    IPC Odometer Programming Method Quick Reference Guide

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

    Read the sentences of the record
    Remedy
    IPC Odometer Programming Method Quick Reference Guide Season Odometer Programming Methods in Use Today 1. IPC reprogramming and setup using the service programming system (SPS). 2. Odometer setup at the electronic service center (ESC) when using an exchange IPC/DIC. 3. Tech 2® – The Tech 2 is used to set up a replacement BCM, which includes loading the odometer value that is displayed and stored in the IPC. A replacement IPC will display the previously stored vehicle odometer value, communicated from the BCM, after cycling the ignition or driving the vehicle. *The odometer programming is integrated as part of the BCM programming procedure. It is not a stand-alone event.

  2. Manufacturer communication2000–2006 GMC YUKON DENALI ・ 2017-08-15

    Instrument Panel Cluster Mileage Programming Information

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      Repair

      • When the odometer cannot be set to the actual vehicle mileage, it must be set at zero and a label affixed to the driver's door frame by the service agent.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to 2014 and prior GM passenger cars and trucks.
    • Repair：When the odometer cannot be set to the actual vehicle mileage, it must be set at zero and a label affixed to the driver's door frame by the service agent.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This Preliminary Information communication provides information to the technician that after replacing the Instrument Panel Cluster the exchange center is unable to program the actual mileage on the odometer or the actual mileage is unknown. Dealer will need to follow dealer to the General Motors service policies and procedures manual section 3.2.4 odometer servicing.

  3. Owner complaint2003 GMC YUKON DENALI ・ 2008-07-17

    Multiple electrical failures: turn signal activates hazard lights, inoperative gauges, battery failure, and gear shift noise

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

    Read the sentences of the record
    Fault
    THE CONTACT STATED THAT EVERYTIME HE ACTIVATED HIS LEFT TURN SIGNAL, THE HAZARD WARNING LIGHTS WOULD ILLUMINATE. (3 more)
    Remedy
    HE TOOK THE VEHICLE TO THE DEALER ON NUMEROUS OCCASIONS AND A TECHNICIAN REPLACED THE BATTERY AND ALTERNATOR TWICE, AND THE ENTIRE INSTRUMENT CONTROL PANEL AS WELL.