Skip to content
FaultCrate
日本語

This is an open preview: every record can be read without an account.

GMC Yukon 2000–2006

GMC YukonModel years 2000–2006

Change vehicle →
Clear the search
2 conditions added

Common on this vehicle:Gauge or instrument faultLeakNoiseParking brakeWarning light

Record by record

14 records state a cause or a remedy. Each record is shown as short labels in the order fault → finding the cause → correction. Press a label to narrow to the records that state it.

Read the records one by one (10)

TIRES6

  1. Manufacturer communication2003–2006 GMC YUKON DENALI ・ 2022-06-13

    Tire Pressure Service Information

    1. 1Fault

      • Ride, handling and road noise concerns may be caused by improperly adjusted tire pressure.
      • During cold weather the Tire Pressure Monitor (TPM) indicator (a yellow horseshoe with an exclamation point) may illuminate.

    2. 2Finding the cause

      Steps to confirm (in the document’s order)

      1. The first step in diagnosing these concerns is to verify that the tires are inflated to the correct pressures.
      2. The tire placard is on the driver's side front or rear door edge, the center pillar, or the rear compartment lid.
      3. Generally a 5.6°C (10°F) temperature change equals a 6.9 kPa (1 psi) tire pressure change.
      4. A "cold" tire is one that has sat for at least 3 hours or been driven no more than 1.6 km (1 mi).

    3. 3Correction

      Repair

      • If the indicator goes off after the tires warm up, reset the pressure to placard pressure at the cold temperature.

      Caution

      • The recommended inflation pressure is not the pressure printed on the tire sidewall.
      • Always inspect and adjust the pressure when the tires are cold.
      • Vehicles with different front and rear pressures need to be adjusted after tire rotation.
      • To prevent electrostatic discharge damage to the Tire Pressure Monitoring Sensor (TPMS), the technician should be statically discharged before checking or filling tires.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to 2022 and prior GM passenger cars and light duty trucks.
    • Condition：Ride, handling and road noise concerns may be caused by improperly adjusted tire pressure.
    • Confirm：The first step in diagnosing these concerns is to verify that the tires are inflated to the correct pressures.
    • Confirm：The tire placard is on the driver's side front or rear door edge, the center pillar, or the rear compartment lid.
    • Caution：The recommended inflation pressure is not the pressure printed on the tire sidewall.
    • Confirm：Generally a 5.6°C (10°F) temperature change equals a 6.9 kPa (1 psi) tire pressure change.
    • Confirm：A "cold" tire is one that has sat for at least 3 hours or been driven no more than 1.6 km (1 mi).
    • Caution：Always inspect and adjust the pressure when the tires are cold.
    • Condition：During cold weather the Tire Pressure Monitor (TPM) indicator (a yellow horseshoe with an exclamation point) may illuminate.
    • Repair：If the indicator goes off after the tires warm up, reset the pressure to placard pressure at the cold temperature.
    • Caution：Vehicles with different front and rear pressures need to be adjusted after tire rotation.
    • Caution：To prevent electrostatic discharge damage to the Tire Pressure Monitoring Sensor (TPMS), the technician should be statically discharged before checking or filling tires.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks.

  2. Manufacturer communication2004–2006 GMC YUKON ・ 2006-05-03

    Aftermarket Wheels/Tire Pressure Monitor/FMVSS 138

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      SERVICE VME - AFTERMARKET WHEELS/TIRE PRESSURE MONITOR/FMVSS 138. *TT

    Read the sentences of the record
    Remedy
    SERVICE VME - AFTERMARKET WHEELS/TIRE PRESSURE MONITOR/FMVSS 138. *TT

  3. Manufacturer communication2004 GMC YUKON ・ 2005-09-06

    Tire Pressure Monitor Reset/Learn Procedure

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

    Read the sentences of the record
    Remedy
    TIRE PRESSURE MONITOR RESET/LEARN-WHEN THE PRESSURE IN THE AFFECTED TIRE WAS SET TO SPECIFICATION ON SOME VEHICLES, THE CHECK TIRE PRESSURE AND OR XX TIRE HIGH/LOW DISPLAY IS CANCELED WITHIN 20 SECONDS OF THE PRESSURE ADJUSTMENT. *SC

  4. Manufacturer communication2004–2005 GMC YUKON ・ 2004-12-04

    Slow Tire Leak or Low Tire Pressure Warning Message

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      SLOW TIRE LEAK OR LOW TIRE PRESSURE WARNING MESSAGE. *EH

    Read the sentences of the record
    Remedy
    SLOW TIRE LEAK OR LOW TIRE PRESSURE WARNING MESSAGE. *EH

  5. Manufacturer communication2004 GMC YUKON ・ 2004-02-25

    Low Tire Pressure Light on Instrument Cluster

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      LOW TIRE PRESSURE LIGHT ILLUMINATED ON INSTRUMENT CLUSTER. SERVICE VME. SIT BULLETIN 1411230. *TT

    Read the sentences of the record
    Remedy
    LOW TIRE PRESSURE LIGHT ILLUMINATED ON INSTRUMENT CLUSTER. SERVICE VME. SIT BULLETIN 1411230. *TT

  6. Manufacturer communication2004 GMC YUKON DENALI ・ 2003-11-20

    Low Tire Pressure Light On After Installing Aftermarket Wheels/Tires

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      LOW TIRE PRESSURE LIGHT ON AFTER INSTALLING AFTERMARKET WHEELS/TIRES. *TT

    Read the sentences of the record
    Remedy
    LOW TIRE PRESSURE LIGHT ON AFTER INSTALLING AFTERMARKET WHEELS/TIRES. *TT

No component category2

  1. Manufacturer communication2004–2005 GMC FULL-SIZE UTILITY TRUCKS (YUKON) ・ 2005-05-01

    Tire Pressure Monitor system: messages, diagnosis and sensor relearn

    1. 1Fault

      • The Passenger Door Module (PDM) is the receiver in the full-size utility truck; the receiver module varies by vehicle platform.
      • "Check Tire Pressure" message: a sensor that detects a 1.6 psi (11 kPa) change in pressure transmits in re-measure mode; if the system detects a significant loss of pressure in any tire, the message is displayed on the DIC and the low tire pressure indicator is illuminated on the IPC.
      • "Service Tire Monitor" message: if the PDM detects a malfunction in the TPM system, it causes the DIC to display this message.

    2. 2Finding the cause

      Steps to confirm (in the document’s order)

      1. The "Service Tire Monitor" message is not normal system operation; DTCs should be set when it is displayed.
      2. Always check and adjust the tire pressures cold; as a rule of thumb, tire pressure changes one psi for every 10° F (6.9 kPa for every 5.6° C).

    3. 3Correction

      Repair

      1. Both the message and the indicator can be cleared by adjusting the tire pressure to the recommended pressure.
      2. The tire pressure sensor relearn procedure must be performed after every PDM replacement, every sensor replacement and every tire rotation.
      3. J-46079 TPM Diagnostic Tool method: turn the ignition ON with the engine OFF and set the parking brake, then put the PDM in TPM learn mode by cycling the parking lamps ON and OFF 4 times within 4 seconds; the horn chirps and the low tire pressure indicator begins to flash.
      4. Proceed in the order left front, right front, right rear, left rear: starting with the left front tire, hold the antenna of the J-46079 against the tire sidewall close to the wheel rim at the valve stem and momentarily press the activate button.

      Caution

      • A "Check Tire Pressure" message does not set system codes; it is normal operation, meant to alert the driver to check and adjust tire pressure.
      • Always relearn the system before replacing a suspect sensor.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：A Tire Pressure Monitor (TPM) system was added to certain GMC and Chevrolet full-size utility trucks for model year 2004 and continues for 2005.
    • Condition：The Passenger Door Module (PDM) is the receiver in the full-size utility truck; the receiver module varies by vehicle platform.
    • Condition："Check Tire Pressure" message: a sensor that detects a 1.6 psi (11 kPa) change in pressure transmits in re-measure mode; if the system detects a significant loss of pressure in any tire, the message is displayed on the DIC and the low tire pressure indicator is illuminated on the IPC.
    • Caution：A "Check Tire Pressure" message does not set system codes; it is normal operation, meant to alert the driver to check and adjust tire pressure.
    • Repair：Both the message and the indicator can be cleared by adjusting the tire pressure to the recommended pressure.
    • Condition："Service Tire Monitor" message: if the PDM detects a malfunction in the TPM system, it causes the DIC to display this message.
    • Confirm：The "Service Tire Monitor" message is not normal system operation; DTCs should be set when it is displayed.
    • Confirm：Always check and adjust the tire pressures cold; as a rule of thumb, tire pressure changes one psi for every 10° F (6.9 kPa for every 5.6° C).
    • Caution：Always relearn the system before replacing a suspect sensor.
    • Repair：The tire pressure sensor relearn procedure must be performed after every PDM replacement, every sensor replacement and every tire rotation.
    • Repair：J-46079 TPM Diagnostic Tool method: turn the ignition ON with the engine OFF and set the parking brake, then put the PDM in TPM learn mode by cycling the parking lamps ON and OFF 4 times within 4 seconds; the horn chirps and the low tire pressure indicator begins to flash.
    • Repair：Proceed in the order left front, right front, right rear, left rear: starting with the left front tire, hold the antenna of the J-46079 against the tire sidewall close to the wheel rim at the valve stem and momentarily press the activate button.

    Open this issue of GM TechLink ↗ The points above are read from an article of TechLink, GM’s monthly publication for dealership technicians. The article itself is not reproduced here.

    Remedy
    Tire Pressure Monitor A Tire Pressure Monitor (TPM) system was added to certain GMC and Chevrolet full-size utility trucks for model year 2004 and continues for 2005. The PDM is the receiver in the full-size utility truck. The receiver module varies by vehicle platform. “Check Tire Pressure” message -- If a sensor detects a 1.6 psi (11 kPa) change in pressure, it transmits in re-measure mode. If the system detects a significant loss of tire pressure in any tire, the Check Tire Pressure message is displayed on the DIC and the low tire pressure indicator is illuminated on the IPC. TIP: A “Check Tire Pressure” message will not set system codes. This is normal operation of the system. The purpose of this message is to alert the driver to check and adjust tire pressure. TIP: Both the message and indicator can be cleared by adjusting the tire pressure to the recommended pressure. “Service Tire Monitor” message -- If the PDM detects a malfunction in the TPM system, it will cause the DIC to display the Service Tire Monitor message. TIP: The “Service Tire Monitor” message is not a normal system operation. DTCs should be set when this message is displayed. - Always check and adjust the tire pressures COLD. As a rule of thumb, tire pressure will change one psi for every 10° F (6.9 kPa for every 5.6° C). - Always ‘relearn’ the system before replacing a suspect sensor. The tire pressure sensor relearn procedure must be performed after every PDM replacement, every sensor replacement, and every tire rotation. J-46079 TPM Diagnostic Tool Method -- Turn the ignition ON with the engine OFF, and set the parking brake. Place the PDM in TPM learn mode by cycling the parking lamps ON and OFF 4 times within 4 seconds. The horn will chirp and the low tire pressure indicator will begin to flash. Proceed in this order: left front, right front, right rear, left rear. Starting with the left front tire, hold the antenna of the J-46079 against the tire sidewall close to the wheel rim at the valve stem, and momentarily press the activate button.

  2. Manufacturer communication2004 GMC YUKON ・ 2004-11-01

    Tire pressure monitor: direct (RF) system and its sensor learn procedure

    1. 1Fault

      • The direct type uses a pressure sensor/transmitter in each wheel and notifies the driver when a tire pressure is out of specification.

    2. 2Finding the cause

      Steps to confirm (in the document’s order)

      • On some vehicles the CHECK TIRE PRESSURE and/or XX TIRE HIGH/LOW display cancels within 20 seconds of setting the pressure to specification; on others the DIC display can take up to 20 minutes, or cancels at 20 mph (32 km/h) or greater.

    3. 3Correction

      Repair

      • After a tire rotation the direct system needs a learn procedure to identify the new location of each pressure sensor; refer to SI.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Tahoe/Yukon/Denali, model year 04: direct (RF) system, Learn procedure, by the exterior lamp switch and a pressure change, or with J-46079.
    • Applies to：Suburban/Yukon XL/Denali XL, model year 04: direct (RF) system, Learn procedure, by the exterior lamp switch and a pressure change, or with J-46079.
    • Condition：The direct type uses a pressure sensor/transmitter in each wheel and notifies the driver when a tire pressure is out of specification.
    • Repair：After a tire rotation the direct system needs a learn procedure to identify the new location of each pressure sensor; refer to SI.
    • Confirm：On some vehicles the CHECK TIRE PRESSURE and/or XX TIRE HIGH/LOW display cancels within 20 seconds of setting the pressure to specification; on others the DIC display can take up to 20 minutes, or cancels at 20 mph (32 km/h) or greater.

    Open this issue of GM TechLink ↗ The points above are read from an article of TechLink, GM’s monthly publication for dealership technicians. The article itself is not reproduced here.

    Remedy
    Tire Pressure Monitor Reset/Learn Tahoe/Yukon/Denali direct (RF) 04 Learn Exterior lamp switch/Pressure delta, or J-46079 Suburban/Yukon XL/Denali XL direct (RF) 04 Learn Exterior lamp switch/Pressure delta, or J-46079 The direct type uses a pressure sensor/transmitter mounted in each wheel. When an out of specification tire pressure is detected, the driver is notified. When tires are rotated, the direct system requires a learn procedure to identify the new location of each pressure sensor. Refer to SI for details. When the pressure in the affected tire is set to specification on some vehicles, the CHECK TIRE PRESSURE and/or XX TIRE HIGH/LOW display is canceled within 20 seconds of the pressure adjustment. On other vehicles, the DIC displays can take up to 20 minutes to cancel, or will cancel when the vehicle speed is 20 mph (32 km/h) or greater.

ELECTRICAL SYSTEM1

  1. Manufacturer communication2000–2006 GMC YUKON ・ 2024-10-25(4 earlier editions of this document folded here)

    Tire Pressure Monitor and Diagnostic Tools Software Update

    1. 1Fault

      • The process for reaching the GM Tools site has changed.

    2. 2Finding the cause

      Not stated

    3. 3Correction

      This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester  and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.

    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：All brands and models, model years 1995 - 2025.
    • Condition：The process for reaching the GM Tools site has changed.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester  and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.

SUSPENSION1

  1. Manufacturer communication2004–2005 GMC YUKON ・ 2005-11-08

    Tire Slowly Loses Air and Low Tire Pressure Warning

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      TIRE SLOWLY LOSES AIR, LOW TIRE PRESSURE WARNING LIGHT ON, CHECK TIRE PRESSURE MESSAGE DISPLAYED. *TT

    Read the sentences of the record
    Remedy
    TIRE SLOWLY LOSES AIR, LOW TIRE PRESSURE WARNING LIGHT ON, CHECK TIRE PRESSURE MESSAGE DISPLAYED. *TT

Showing 10 of the 14 you can open. Narrow the search to see the rest.