Skip to content
FaultCrate

This is an open preview: every record can be read without an account.

GMC Yukon 2000–2006

GMC YukonModel years 2000–2006

Change vehicle →
Clear the search
2 conditions added

Common on this vehicle:Does not startStalls or shuts offWarning light

Possible causes

Warning light, Security light2 records
Brakes
Transmission and driveline
Electrical, wiring and power
Engine
Exhaust and emissions
Fuel system
0Brake pipe (brake line) corrosion and rupture0ABS light with C0265/C0201/U1041 or no communication with brake module (EBCM ground G110)0Front right-hand brake pipe contact with body cross sill - recall 00V-3450Service Brake Booster message on a Hydroboost vehicle with DTC C0136 (instrument cluster not SPS programmed)0Stability System Disabled / Service Stability message with DTC C0455 (bent terminals at the steering wheel position sensor)0Transfer case service light, New Venture Gear transfer case (replace the encoder motor sensor and reprogram the TCCM)0Intermittent MIL, service lamps/messages or DTCs from connector fretting corrosion0Passlock theft deterrent: starts then stalls / no-start with security lamp0Reduced Engine Power from throttle body connector crimp, broken wire or grounds0Crankshaft position sensor may work intermittently or fail (8.1L V8) - recall 07V-5218.1L only0Intake manifold gasket leak (cold idle misfire, lean codes)0Single-cylinder misfire (P0300-P0308) and/or chirp, squeak or tick at camshaft speed: worn cam lobe / lifter, valve or valve spring0P0300 after engine repairs: injector connectors crossed (cylinders 5-7 / 6-8)0Rear bank knock sensor corrosion from water intrusion (P0332)4.8L, 5.3L, 6.0L only0P0420 / P0430 on a new or just-replaced catalytic converter (break-in not completed)0DTC P0446 set with the SES lamp on (replace the EVAP vent solenoid, not the canister)
8 causes not drawn
Causes with no correction stated (2)

Causes the records name for which no check or repair is stated, in a technical document or in a record. Press one for the records that name it.

The documents say what to doOnly records name itThe size of a node, the width of a link and the numbers are records matching this search, not likelihoods.

Candidate cause (the documents say what to do)

Passlock theft deterrent: starts then stalls / no-start with security lamp

A magnet in the ignition cylinder produces a unique voltage across a Hall effect sensor in the ignition housing; the BCM and lock cylinder enable starting.

If the voltage matches the stored value, the BCM signals the PCM to enable fuel.

How to tell

B2960P1631Security light

What to do

  1. A security lamp flashing after an attempted start means the fuel disable command is active.
  2. A scan tool parameter showing 'fuel system disabled' or similar indicates a Passlock issue.
  3. Monitor the Passlock Data Voltage for approximately one minute; the voltage value should not change by more than .02 volt.
  4. If the voltage does not change from 5 volts, check the ignition housing.
  5. The condition is the Security lamp illuminated on the instrument panel, engine stalls or no start, with DTC B2960 (Security System Sensor Data Incorrect but Valid) set; the correction is to inspect and repair the cause of DTC B2960.

Caution: Loss of Ignition 1 voltage to the BCM gives the same start-then-stall behaviour.

What is needed

Parts and materials
Not stated
Labor time
Not stated
Special tools
Not stated
Scan tool
Not stated

Only what the technical documents state. "Not stated" does not mean not needed.

In the records

No record states work done for this cause.

Outside the documents and the records

None of the four pages read is a record of the Yukon or Yukon XL. Two are a shop's records of the Hummer H3 (model year not given; not a vehicle of the Yukon's family), and two are Q&A threads on the Silverado (2001 and 2004). The 2001 Silverado thread holds only questions and advice, with no repair outcome reported.

  • Sky Auto writes, in two Hummer H3 records (2017 and 2024), that a vehicle whose engine sometimes would not start showed a Passlock (security) fault on the diagnostic computer and that the Passlock module was replaced. スカイオート(埼玉)スカイオート(埼玉)
  • In its two Hummer H3 records (2017 and 2024) Sky Auto explains that the Passlock module is in effect the ignition switch, and writes that the replacement starts by taking off the steering wheel and works inward from there. スカイオート(埼玉)スカイオート(埼玉)
  • In its two Hummer H3 records (2017 and 2024) Sky Auto writes that the engine would not start on the module swap alone and that the job was finished with programming after the swap (described as registering the Passlock in the 2017 record). The 2024 record adds that the engine was then confirmed to start. スカイオート(埼玉)スカイオート(埼玉)
  • The owner of the 2004 Silverado (4.3L) on 2CarPros writes that the engine started and died after about two seconds with the security lamp looking normal and no codes stored, that the cause was the Passlock sensor, and that it started after a 30-minute relearn (whether the sensor was replaced is not said). 2CarPros

The sentences above were written by FaultCrate from what shops' public pages and Q&A sites state as fact (none of the pages' wording is shown; a second reader checked each against its pages). A record of another vehicle says which vehicle. A Q&A thread is a question and advice, and may not say how the repair ended. The links below are places to look; the contents of pages not read were not checked.

The pages read, and other places to look (12)

Shops' repair records

Forums and Q&A

Owners' records

See the evidence (1 technical documents, 0 records)

Passages of the technical documents

  • A magnet in the ignition cylinder produces a unique voltage across a Hall effect sensor in the ignition housing; the BCM and lock cylinder enable starting.

    The GM VTD or Passlock system uses the body control module (BCM) and ignition lock cylinder to activate the start function. The ignition cylinder uses a magnet that produces a unique voltage value when rotated in the ignition housing across the Hall effect sensor.

    MOTOR Magazine 2006-04-01

  • If the voltage matches the stored value, the BCM signals the PCM to enable fuel.

    The BCM compares this voltage value to the value stored in the BCM. If the voltage values are the same, the BCM sends a signal to the powertrain control module to enable fuel.

    MOTOR Magazine 2006-04-01

  • If the values do not match, the engine briefly starts and then stalls.

    If the voltage values are not the same, the engine will briefly start, then stall.

    MOTOR Magazine 2006-04-01

  • A security lamp flashing after an attempted start means the fuel disable command is active.

    The quickest way is to look at the security indicator lamp on the instrument panel. If it’s flashing after an attempted start, the fuel disable command has been energized.

    MOTOR Magazine 2006-04-01

Read every statement and its source →

Records

None among the records that can be opened now.

See all 0 records of this cause →

A cause or a result a complaint states is the owner’s view or what a dealer told them, not an established fact.