Skip to content
FaultCrate

This is an open preview: every record can be read without an account.

GMC Yukon 2000–2006

GMC YukonModel years 2000–2006

Change vehicle →
Clear the search
2 conditions added

Common on this vehicle:Warning lightNoiseReduced brakingSeat beltSmoke or fireABS activates (at low speed and the like)Air bag did not deployMisfire or rough idle

issuenoneRemove

Possible causes

Noise, ABS light4 records
Brakes
Body, doors and interior
Transmission and driveline
Electrical, wiring and power
Engine
Exhaust and emissions
1Electronic Brake Control Module: failed0ABS lamp with DTC C0265 (EBCM motor relay circuit) after EBCM replacement0Buzz at the accelerator pedal on the first acceleration after start (Supplemental Brake Assist self-test, normal)0ABS light with C0265/C0201/U1041 or no communication with brake module (EBCM ground G110)0Parking brake linings worn out prematurely, parking brake does not hold (PBR single-shoe drum-in-hat)1500 only0Rattle from the center of the dash (cowl insulator clip)0Snap or popping noise from the front of the vehicle (slot the front crossmember mounting holes)0Headliner or roof rattle (roof drain channel)0Side access door noise (door check link replacement)04L60-E / 4L65-E clunk on 2-3 upshift or 3-2 downshift (normal condition)04L80-E / 4L85-E planetary gear whine in first and second gear0Grind / ratchet noise when shifting into Park in 4LO (characteristic)0Generator whine in the audio system (new ground for radio and amplifier)0Hum or fan noise from the navigation radio (internal cooling fan, normal)0Accessory drive belt whine (power steering pump pulley repositioned)1500 only0Engine vibration or noise at idle felt in the steering wheel or seat (reprogram the PCM)0Single-cylinder misfire (P0300-P0308) and/or chirp, squeak or tick at camshaft speed: worn cam lobe / lifter, valve or valve spring0Oil pump pickup (screen) O-ring cut: engine tick / lifter noise4.8L, 5.3L, 6.0L only0Rear bank knock sensor corrosion from water intrusion (P0332)4.8L, 5.3L, 6.0L only0Exhaust pop or ping noise (replace the heat shield, not the exhaust system)
11 causes not drawn
Causes with no correction stated (2)

Causes the records name for which no check or repair is stated, in a technical document or in a record. Press one for the records that name it.

The documents say what to doOnly records name itThe size of a node, the width of a link and the numbers are records matching this search, not likelihoods.

Candidate cause (the documents say what to do)

ABS light with C0265/C0201/U1041 or no communication with brake module (EBCM ground G110)

Upon inspection, DTCs C0265 and C0201 may be set in the brake module.

There may also be a loss of communication with the brake module.

How to tell

C0201C0265U1041ABS light

What to do

  1. The EBCM ground is on the frame beneath the driver's door; among several grounds it is the heavy 12-gauge wire.
  2. The battery-cable-to-frame ground can cause similar ABS symptoms and can be checked as well.
  3. Clean the area, front and back, using a tool such as a Scotch-Brite Roloc disc or equivalent.
  4. Use the bolts, washers and nuts specified in the bulletin because of their conductive finish.
  5. Cover the front and back of the repair area with rubberized undercoating.

Caution: Do not replace the brake module for this condition; do the ground repair before further EBCM diagnosis.

What is needed

Parts and materials
  • The bolts, washers and nuts specified in the bulletin (for their conductive finish)
  • Rubberized undercoating (to cover the front and back of the repair area)
Labor time
Not stated
Special tools
Not stated
Scan tool
Not stated

Only what the technical documents state. "Not stated" does not mean not needed.

In the records

No record states work done for this cause.

See the evidence (1 technical documents, 0 records)

Passages of the technical documents

  • The bulletin lists 2000-2006 GMC Yukon, Yukon Denali and Yukon XL.

    2000–2006 GMC Yukon, Yukon Denali, Yukon XL

    General Motors (third-party hosted copy at simple-engineering.com) 2009-03-11

  • Upon inspection, DTCs C0265 and C0201 may be set in the brake module.

    Some customers may comment that the ABS light is on. Upon further inspection, DTCs C0265 and C0201 may be set in the brake module.

    General Motors (third-party hosted copy at simple-engineering.com) 2009-03-11

  • DTC U1041 can also set in other modules.

    It is also possible for DTC U1041 to set in other modules.

    General Motors (third-party hosted copy at simple-engineering.com) 2009-03-11

  • There may also be a loss of communication with the brake module.

    There may also be a loss of communication with the brake module.

    General Motors (third-party hosted copy at simple-engineering.com) 2009-03-11

Read every statement and its source →

Records

None among the records that can be opened now.

See all 0 records of this cause →

A cause or a result a complaint states is the owner’s view or what a dealer told them, not an established fact.