Skip to content
FaultCrate
日本語

This is an open preview: every record can be read without an account.

GMC Yukon 2000–2006

GMC YukonModel years 2000–2006

Change vehicle →
Clear the search
2 conditions added

The vehicle (where a record says)

A record is under an engine, a drive or a series only where it says so: the characters of the vehicle identification number filed with a complaint, its text, or what its document says it applies to. A record that does not say is kept as "not stated". The filed numbers and the documents do not tell 4WD from AWD.

Common on this vehicle:Vibration or shudderTyre failure (blowout, tread separation)NoiseWarning lightCorrosion or rustLeakAir conditioning or heaterABS activates (at low speed and the like)

Record by record

4 records state a cause or a remedy. Each record is shown as short labels in the order fault → finding the cause → correction. Press a label to narrow to the records that state it.

Symptom

Component named as the cause

A ribbon is as wide as the records that state both of its ends (only the commonest are drawn). A record that names several symptoms or components runs through each. Orange is records that say the fault came back or was not fixed. Results come from owners’ reports only; one that does not say is “result not stated”. None of this is a likelihood of a cause or a rate at which work succeeds.

Read the records one by one (3)

TIRES2

  1. Manufacturer communication2001–2004 GMC YUKON DENALI ・ 2018-05-21(1 earlier editions of this document folded here)

    Wheel and Tire Mounting and Balancing Notification

    1. 1Fault

      • Customers may say the HVAC blower motor does not work or that no air flows from the vents; it may be intermittent.

    2. 2Finding the cause

      Possible causes

      • One possible cause is the contacts in the HVAC junction block(s) at the right side of the instrument panel.

      Steps to confirm (in the document’s order)

      1. With the ignition on and the blower running, apply light hand pressure to the junction block connectors and see whether the movement affects blower operation.
      2. On junction block X4, locate Pin A6, Circuit 754.
      3. On X4, perform a pin drag test with test probe J-35616-2A (GY).
      4. On junction block X6, locate Pin A, Circuit 542.
      5. On X6, perform a pin drag test with test probe J-35616-42 (RD).

    3. 3Correction

      Repair

      • If the terminal fails the pin drag test, replace the terminal for Pin A6, referring to Junction Block - Right I/P X4 in SI.

      Parts

      • Terminals: 12191812/19 Junction Block X4 Terminal/Tray; 12084590/3 Junction Block X6 Terminal/Tray.

      Part numbers printed in the document

      The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

      Caution

      • Do not replace the HVAC blower motor assembly to correct this condition.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to 2008-2013 GMC Yukon models (note: later than the years this service covers).
    • Applies to：Vehicles built prior to November 1, 2012 are covered.
    • Condition：Customers may say the HVAC blower motor does not work or that no air flows from the vents; it may be intermittent.
    • Cause：One possible cause is the contacts in the HVAC junction block(s) at the right side of the instrument panel.
    • Caution：Do not replace the HVAC blower motor assembly to correct this condition.
    • Confirm：With the ignition on and the blower running, apply light hand pressure to the junction block connectors and see whether the movement affects blower operation.
    • Confirm：On junction block X4, locate Pin A6, Circuit 754.
    • Confirm：On X4, perform a pin drag test with test probe J-35616-2A (GY).
    • Repair：If the terminal fails the pin drag test, replace the terminal for Pin A6, referring to Junction Block - Right I/P X4 in SI.
    • Confirm：On junction block X6, locate Pin A, Circuit 542.
    • Confirm：On X6, perform a pin drag test with test probe J-35616-42 (RD).
    • Parts：Terminals: 12191812/19 Junction Block X4 Terminal/Tray; 12084590/3 Junction Block X6 Terminal/Tray.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This informational bulletin provides information on how to properly mount and balance wheels and tires on heavy duty truck models only

  2. Owner complaint2001 GMC YUKON ・ 2005-02-21

    Tire tread separation and vehicle damage after blowout

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      Not stated

    Read the sentences of the record
    Consequence
    AS A RESULT OF THIS, THE LOOSE TREAD WAS "SLAPPING" EVERY PART OF THE VEHICLE IN THE SURROUNDING AREA CAUSING OVER $4,000 WORTH OF DAMAGE, INCLUDING, BODY DAMAGE, TAILPIPE DAMAGE, ELECTRICAL WIRES CUT, A/C LINES CUT, TAIL LIGHT SEVERED, RUNNING BOARDS BROKEN AND MORE.

AIR BAGS1

  1. Owner complaint2006 GMC YUKON ・ 2017-08-23

    Right front tire hub damaged, tire falling off, tire sensor warning, blower motor not working

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      Not stated

    Read the sentences of the record
    Fault
    MY TIRE IS IN THE MIDST OF FALLING OFF I CONTINUOUSLY GET A NOTICE TO CHECK TIRE SENSOR IN ADDITION I HAVE HAD SEVERAL ELECTRICAL ISSUES INCLUDING THE FAN NOT WORKING INSIDE THE VEHICLE TO TURN ON THE HEAT OR AIR CONDITIONER

Showing 3 of the 4 you can open. Narrow the search to see the rest.