Skip to content
FaultCrate
日本語

This is an open preview: every record can be read without an account.

GMC Yukon 2000–2006

GMC YukonModel years 2000–2006

Change vehicle →
Clear the search
2 conditions added

Common on this vehicle:Gauge or instrument faultLeakStalls or shuts offWarning lightCorrosion or rustMisfire or rough idleDoes not startSmoke or fire

Record by record

7 records state a cause or a remedy. Each record is shown as short labels in the order fault → finding the cause → correction. Press a label to narrow to the records that state it.

Symptom

Component named as the cause

Work done

How it is said to have ended

  • result not stated1

A ribbon is as wide as the records that state both of its ends (only the commonest are drawn). A record that names several symptoms or components runs through each. Orange is records that say the fault came back or was not fixed. Results come from owners’ reports only; one that does not say is “result not stated”. None of this is a likelihood of a cause or a rate at which work succeeds.

Read the records one by one (6)

Known issuesAftermarket part (not the vehicle as built): Fram G3727 replacement fuel filter connector - recall 06E-0431

  1. Recall2000–2005 GMC YUKON ・ —

    Fram Replacement Fuel Filters (P/N G3727) Recall

    1. 1Fault

      • The connector on the fuel filter was not manufactured to specification, so the O-ring may not seat correctly on the fuel line; this may cause an inadequate seal, potentially leading to a fuel leak (wetting or dripping) and possible vehicle fire.

    2. 2Finding the cause

      Steps to confirm (in the document’s order)

      • The part number (G3727), country of origin (Mexico) and the date code (e.g., X60031) are located on the side of the fuel filter.

    3. 3Correction

      Repair

      • Honeywell will replace the subject fuel filters at no charge to the customer.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：This is an equipment recall of fuel filters manufactured by Interfil in Mexico and sold by Honeywell under the FRAM brand name, part number G3727, intended for aftermarket installation on the vehicle applications in the attached table.
    • Applies to：Only filters with date codes X52911 through X60801 sequentially or X600141, and with a Mexico country of origin marking on the filter housing, are subject to the recall.
    • Applies to：The application table lists YUKON 1992 - 2005, YUKON DENALI 2005, YUKON DENALI XL 2005, YUKON XL 1500 2000 - 2005 and YUKON XL 2500 2000 - 2005.
    • Condition：The connector on the fuel filter was not manufactured to specification, so the O-ring may not seat correctly on the fuel line; this may cause an inadequate seal, potentially leading to a fuel leak (wetting or dripping) and possible vehicle fire.
    • Confirm：The part number (G3727), country of origin (Mexico) and the date code (e.g., X60031) are located on the side of the fuel filter.
    • Repair：Honeywell will replace the subject fuel filters at no charge to the customer.
    Cause
    CERTAIN REPLACEMENT FUEL FILTERS, FRAM BRAND NAME P/N G3727, WITH DATE CODES X52911 THROUGH X60801 SEQUENTIALLY OR X600141 AND A MEXICO COUNTRY OR ORIGIN MARKING ON THE FUEL FILTER HOUSING MANUFACTURED FROM OCTOBER 18, 2005, THROUGH MARCH 21, 2006, SOLD FOR USE ON THE VEHICLES LISTED ABOVE AND ON CERTAIN SCHOOL BUSES. (TO SEE THE SCHOOL BUS ENGINE SIZES, CLICK ON "DOCUMENT SEARCH" AND THEN "BUS APPLICATIONS"). THE CONNECTOR ON THE FUEL FILTER WAS NOT MANUFACTURED TO HONEYWELL'S SPECIFICATION. AS A RESULT, THE O-RING MAY NOT SEAT CORRECTLY ON THE FUEL LINE.
    Remedy
    HONEYWELL WILL NOTIFY OWNERS AND REPLACE THE FUEL FILTERS FREE OF CHARGE. THE RECALL BEGAN ON OCTOBER 18, 2006. OWNERS MAY CONTACT FRAM CUSTOMER SERVICE AT 1-800-890-2075 (OPTION 1).
    Consequence
    THIS CONDITION MAY CAUSE AN INADEQUATE SEAL AT THE CONNECTION, POTENTIALLY LEADING TO A FUEL LEAK. IN THE PRESENCE OF AN IGNITION SOURCE, A FIRE COULD OCCUR.

Known issuesEngine fuel rail crossover tube retainer screws may break (5.3L RPO L59) - recall 04V-3761

  1. Recall2005 GMC YUKON ・ 2004-08-05

    Fuel Rail Crossover Tube Retainer Screws Recall

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      Not stated

      What the documents say to do

      Engine fuel rail crossover tube retainer screws may break (5.3L RPO L59) - recall 04V-376

      Confirm

      • Check for leaks: ignition ON with the engine OFF for 2 seconds, ignition OFF for 10 seconds, ignition ON with the engine OFF, then visually inspect for fuel leaks.

      Repair

      1. Dealers inspect the fuel rail crossover tube and replace the retainer screws if necessary.
      2. Hold the fuel crossover tube retainer to the bracket on the fuel rail with locking pliers, using enough force to keep the retainer from moving without damaging any parts.

      Caution

      • The GM bulletin lists Tahoe and Yukon models because Canadian vehicles are included in the bulletin.
    Read the sentences of the record
    Cause
    On certain vehicles, the fuel rail crossover tube retainer screws were not manufactured to specifications and may break. If a tube retainer screw breaks, fuel could leak from the fuel rail crossover joint, the engine may stall and, if an ignition source were present, an engine compartment fire could occur. Correction: Dealers will inspect the fuel rail crossover tube assembly and, if necessary, replace the two tube retainer screws.

ENGINE AND ENGINE COOLING2

  1. Manufacturer communication2000–2006 GMC YUKON DENALI ・ 2017-08-15(1 earlier editions of this document folded here)

    Engine Check Lamp P0442 Evaporative Emissions System Notification

    1. 1Fault

      • The service engine soon lamp (MIL) is on for DTC P0442, but a leak cannot be verified with the system test in the service information.

    2. 2Finding the cause

      Steps to confirm (in the document’s order)

      1. With the scan tool, command the EVAP system CLOSED, start the engine and watch the tank pressure sensor value for about two minutes.
      2. If the tank pressure value changes (shows vacuum), remove the purge solenoid and pressurize its fuel tank side with the GE 41413-A / J 41413-A tester.
      3. If the tank pressure value does not change, install the CH-48096 adaptor between the purge line from the canister and the purge solenoid; use no other adaptor or pressurization method.
      4. With the EVAP system CLOSED, pressurize through the adaptor and let the system stabilize, watching the gauge for at least 5 minutes, then add smoke.
      5. Look for smoke or UV trace fluid at the purge solenoid, the engine side, the fuel cap or capless fill door, and the canister vent solenoid filter or fresh-air line.
      1 more points

    3. 3Correction

      Repair

      • If smoke passes through the purge solenoid, replace the purge solenoid.

      Caution

      • After verifying P0442, do not disturb any fuel system component before testing.
      • Test pressure must not exceed 13 in H2O (0.5 PSI (= 3.45 kPa)); more can make components perform inaccurately and lead to misdiagnosis.
      • A large temperature difference between vehicle, shop and tester seriously affects accuracy; let the vehicle adjust to shop temperature first.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to 2016 and prior passenger cars and trucks.
    • Condition：The service engine soon lamp (MIL) is on for DTC P0442, but a leak cannot be verified with the system test in the service information.
    • Caution：After verifying P0442, do not disturb any fuel system component before testing.
    • Confirm：With the scan tool, command the EVAP system CLOSED, start the engine and watch the tank pressure sensor value for about two minutes.
    • Confirm：If the tank pressure value changes (shows vacuum), remove the purge solenoid and pressurize its fuel tank side with the GE 41413-A / J 41413-A tester.
    • Repair：If smoke passes through the purge solenoid, replace the purge solenoid.
    • Confirm：If the tank pressure value does not change, install the CH-48096 adaptor between the purge line from the canister and the purge solenoid; use no other adaptor or pressurization method.
    • Confirm：With the EVAP system CLOSED, pressurize through the adaptor and let the system stabilize, watching the gauge for at least 5 minutes, then add smoke.
    • Confirm：Look for smoke or UV trace fluid at the purge solenoid, the engine side, the fuel cap or capless fill door, and the canister vent solenoid filter or fresh-air line.
    • Confirm：If smoke testing finds nothing, the leak may exist only under vacuum: use the scan tool Purge/Seal function to pull a vacuum and watch the FTP sensor parameter for vacuum decay.
    • Caution：Test pressure must not exceed 13 in H2O (0.5 PSI (= 3.45 kPa)); more can make components perform inaccurately and lead to misdiagnosis.
    • Caution：A large temperature difference between vehicle, shop and tester seriously affects accuracy; let the vehicle adjust to shop temperature first.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.

  2. Owner complaint2001 GMC YUKON ・ 2006-03-20

    Transmission seal failure with fuel leak and other defects

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      Not stated

    Read the sentences of the record
    Fault
    THE RADIATOR SEAL FAILED. (1 more)

FUEL SYSTEM, GASOLINE2

  1. Owner complaint2001 GMC YUKON ・ 2005-09-27

    Fuel pump failed in May 2005

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

    Read the sentences of the record
    Fault
    DT: THE CONTACT STATED IN MAY 2005 FUEL PUMP FAILED ON 2001 GMC YUKON XL 1500.
    Remedy
    HE HAD THE FUEL PUMP REPLACED WITH A NEW ONE.
    Inspection
    WHEN HE PULLED THE OLD ONE OUT HE NOTICED THAT THE WIRES WERE BURNED AND MELTED TOGETHER.

  2. Owner complaint2001 GMC YUKON ・ 2004-06-10

    Gas leaks from filler pipe when refueling

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      Not stated

    Read the sentences of the record
    Fault
    WHEN PUMPING GAS IN THE GAS TANK, THE GAS WOULD LEAKS FROM THE FILLER PIPE.
    Inspection
    THE MECHANIC INFORMED THE OWNER THAT THE WIRING HARNESS HAS MELTED FROM THE FUEL PUMP. *AK

Showing 6 of the 7 you can open. Narrow the search to see the rest.