Skip to content
FaultCrate
日本語

This is an open preview: every record can be read without an account.

GMC Yukon 2000–2006

GMC YukonModel years 2000–2006

Change vehicle →
Clear the search
2 conditions added

Common on this vehicle:Warning lightLeakNoiseSmoke or fireGauge or instrument faultHard start or long crankMisfire or rough idleDoes not start

Record by record

3 records state a cause or a remedy. Each record is shown as short labels in the order fault → finding the cause → correction. Press a label to narrow to the records that state it.

Symptom

Component named as the cause

A ribbon is as wide as the records that state both of its ends (only the commonest are drawn). A record that names several symptoms or components runs through each. Orange is records that say the fault came back or was not fixed. Results come from owners’ reports only; one that does not say is “result not stated”. None of this is a likelihood of a cause or a rate at which work succeeds.

Read the records one by one (3)

ENGINE AND ENGINE COOLING3

  1. Manufacturer communication2000–2006 GMC YUKON DENALI ・ 2019-03-18

    Diagnostic Tip: Using Smoke Machine and Ultrasonic Detector for Air Leaks

    1. 1Fault

      • The SES light is on, and initial diagnosis may show fuel trim and/or O2 sensor related codes such as P0171, P0174, P0420 and P0430.

    2. 2Finding the cause

      Steps to confirm (in the document’s order)

      1. If normal SI diagnostics do not resolve it and an intake vacuum leak or exhaust leak is suspected, the J41413-200 Evaporative System Tester smoke machine, the J-41416 ultrasonic leak tester, or soapy water with low pressure air into the tailpipe may help find the leak.
      2. For an intake leak, the smoke can be introduced into the brake booster hose or the oil dipstick tube.
      3. Soapy water can be sprayed near the gasket and seams and on all vacuum nipples.
      4. For an exhaust leak, a hose into the tailpipe carrying smoke or air, sealed with shop towels, is effective.
      5. Then spray soapy water around the seals, seams and bosses.
      1 more points

    3. 3Correction

      Caution

      • All of these tests are much more effective if the throttle body is covered/sealed.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to all 2000 - 2019 models with gasoline engines.
    • Condition：The SES light is on, and initial diagnosis may show fuel trim and/or O2 sensor related codes such as P0171, P0174, P0420 and P0430.
    • Confirm：If normal SI diagnostics do not resolve it and an intake vacuum leak or exhaust leak is suspected, the J41413-200 Evaporative System Tester smoke machine, the J-41416 ultrasonic leak tester, or soapy water with low pressure air into the tailpipe may help find the leak.
    • Caution：All of these tests are much more effective if the throttle body is covered/sealed.
    • Confirm：For an intake leak, the smoke can be introduced into the brake booster hose or the oil dipstick tube.
    • Confirm：Soapy water can be sprayed near the gasket and seams and on all vacuum nipples.
    • Confirm：For an exhaust leak, a hose into the tailpipe carrying smoke or air, sealed with shop towels, is effective.
    • Confirm：Then spray soapy water around the seals, seams and bosses.
    • Confirm：These methods are very good for finding small leaks around the O2 sensor bosses and slight cracks in an intake plenum or gasket.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks using the evaporative emission cart smoke machine and ultrasonic leak detector tools.

  2. Manufacturer communication2000–2006 GMC YUKON DENALI ・ 2017-08-15

    Engine Check Lamp P0442 Evaporative Emissions System Notification

    1. 1Fault

      • The service engine soon lamp (MIL) is on for DTC P0442, but a leak cannot be verified with the system test in the service information.

    2. 2Finding the cause

      Steps to confirm (in the document’s order)

      1. With the scan tool, command the EVAP system CLOSED, start the engine and watch the tank pressure sensor value for about two minutes.
      2. If the tank pressure value changes (shows vacuum), remove the purge solenoid and pressurize its fuel tank side with the GE 41413-A / J 41413-A tester.
      3. If the tank pressure value does not change, install the CH-48096 adaptor between the purge line from the canister and the purge solenoid; use no other adaptor or pressurization method.
      4. With the EVAP system CLOSED, pressurize through the adaptor and let the system stabilize, watching the gauge for at least 5 minutes, then add smoke.
      5. Look for smoke or UV trace fluid at the purge solenoid, the engine side, the fuel cap or capless fill door, and the canister vent solenoid filter or fresh-air line.
      1 more points

    3. 3Correction

      Repair

      • If smoke passes through the purge solenoid, replace the purge solenoid.

      Caution

      • After verifying P0442, do not disturb any fuel system component before testing.
      • Test pressure must not exceed 13 in H2O (0.5 PSI (= 3.45 kPa)); more can make components perform inaccurately and lead to misdiagnosis.
      • A large temperature difference between vehicle, shop and tester seriously affects accuracy; let the vehicle adjust to shop temperature first.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to 2016 and prior passenger cars and trucks.
    • Condition：The service engine soon lamp (MIL) is on for DTC P0442, but a leak cannot be verified with the system test in the service information.
    • Caution：After verifying P0442, do not disturb any fuel system component before testing.
    • Confirm：With the scan tool, command the EVAP system CLOSED, start the engine and watch the tank pressure sensor value for about two minutes.
    • Confirm：If the tank pressure value changes (shows vacuum), remove the purge solenoid and pressurize its fuel tank side with the GE 41413-A / J 41413-A tester.
    • Repair：If smoke passes through the purge solenoid, replace the purge solenoid.
    • Confirm：If the tank pressure value does not change, install the CH-48096 adaptor between the purge line from the canister and the purge solenoid; use no other adaptor or pressurization method.
    • Confirm：With the EVAP system CLOSED, pressurize through the adaptor and let the system stabilize, watching the gauge for at least 5 minutes, then add smoke.
    • Confirm：Look for smoke or UV trace fluid at the purge solenoid, the engine side, the fuel cap or capless fill door, and the canister vent solenoid filter or fresh-air line.
    • Confirm：If smoke testing finds nothing, the leak may exist only under vacuum: use the scan tool Purge/Seal function to pull a vacuum and watch the FTP sensor parameter for vacuum decay.
    • Caution：Test pressure must not exceed 13 in H2O (0.5 PSI (= 3.45 kPa)); more can make components perform inaccurately and lead to misdiagnosis.
    • Caution：A large temperature difference between vehicle, shop and tester seriously affects accuracy; let the vehicle adjust to shop temperature first.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.

  3. Manufacturer communication2003–2006 GMC YUKON ・ 2011-03-16

    Oil Consumption/Exhaust Smoke - PCV Baffle or Lifter Concern

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      BUICK/CADILLAC/CHEVROLET/GMC/HUMMER/PONTIAC/SAAB: OIL CONSUMPTION AND/OR EXHAUST SMOKE-POSSIBLE PCV BAFFLE OR LIFTER CONCERN. UPON INSPECTION, OBVIOUS OIL WILL BE FOUND IN THE INTAKE MANIFOLD AND/OR PCV VACUUM TUBE. *PE UPDATED 3/21/11. *PE UPDATED 5/9/11. *PE UPDATED 5/25/11. *PE UPDATED 06/16/2011. *KB UPDATED A SECOND TIME ON 06/16/2011. *KB UPDATED 6/27/11. *PE

    Read the sentences of the record
    Remedy
    BUICK/CADILLAC/CHEVROLET/GMC/HUMMER/PONTIAC/SAAB: OIL CONSUMPTION AND/OR EXHAUST SMOKE-POSSIBLE PCV BAFFLE OR LIFTER CONCERN. UPON INSPECTION, OBVIOUS OIL WILL BE FOUND IN THE INTAKE MANIFOLD AND/OR PCV VACUUM TUBE. *PE UPDATED 3/21/11. *PE UPDATED 5/9/11. *PE UPDATED 5/25/11. *PE UPDATED 06/16/2011. *KB UPDATED A SECOND TIME ON 06/16/2011. *KB UPDATED 6/27/11. *PE