Skip to content
FaultCrate

This is an open preview: every record can be read without an account.

GMC Yukon 2000–2006

GMC YukonModel years 2000–2006

Change vehicle →
Clear the search
2 conditions added

The vehicle (where a record says)

A record is under an engine, a drive or a series only where it says so: the characters of the vehicle identification number filed with a complaint, its text, or what its document says it applies to. A record that does not say is kept as "not stated". The filed numbers and the documents do not tell 4WD from AWD.

Common on this vehicle:Warning lightNoiseLoss of engine power, no accelerationMisfire or rough idleLeakGauge or instrument faultStalls or shuts offDoes not start

Possible causes

Warning light, Engine68 records
Engine
Exhaust and emissions
Electrical, wiring and power
Brakes
Transmission and driveline
Fuel system
5Single-cylinder misfire (P0300-P0308) and/or chirp, squeak or tick at camshaft speed: worn cam lobe / lifter, valve or valve spring2Throttle Body: failed1DTCs P2108, P1516 and U0107 (do not replace the TAC module)1P0300 after engine repairs: injector connectors crossed (cylinders 5-7 / 6-8)1Rear bank knock sensor corrosion from water intrusion (P0332)4.8L, 5.3L, 6.0L only0Crankshaft position sensor may work intermittently or fail (8.1L V8) - recall 07V-5218.1L only5P0420 / P0430 on a new or just-replaced catalytic converter (break-in not completed)1Oxygen Sensor: failed1Reduced Engine Power from throttle body connector crimp, broken wire or grounds0Intermittent MIL, service lamps/messages or DTCs from connector fretting corrosion0Brake pipe (brake line) corrosion and rupture0ABS light with C0265/C0201/U1041 or no communication with brake module (EBCM ground G110)0Front right-hand brake pipe contact with body cross sill - recall 00V-3450Service Brake Booster message on a Hydroboost vehicle with DTC C0136 (instrument cluster not SPS programmed)0Stability System Disabled / Service Stability message with DTC C0455 (bent terminals at the steering wheel position sensor)0Transfer case service light, New Venture Gear transfer case (replace the encoder motor sensor and reprogram the TCCM)0DTC P0446 set with the SES lamp on (replace the EVAP vent solenoid, not the canister)
9 causes not drawn
Causes with no correction stated (5)

Causes the records name for which no check or repair is stated, in a technical document or in a record. Press one for the records that name it.

The documents say what to doOnly records name itThe size of a node, the width of a link and the numbers are records matching this search, not likelihoods.

Candidate cause (the documents say what to do)

DTC P0446 set with the SES lamp on (replace the EVAP vent solenoid, not the canister)

0 of the records matching this search name this component as the cause.

How to tell

P0446Check engine / Service Engine Soon

What to do

  1. Replace the EVAP vent solenoid.

Caution: Do not replace the EVAP canister. The reference bulletin is 04-06-04-055.

What is needed

Parts and materials
  • EVAP vent solenoid
Labor time
Not stated
Special tools
Not stated
Scan tool
Not stated

Only what the technical documents state. "Not stated" does not mean not needed.

In the records

No record states work done for this cause.

See the evidence (1 technical documents, 0 records)

Passages of the technical documents

  • 2000-2003 Tahoe, Suburban, Yukon, Yukon XL: DTC P0446 is set and the SES lamp is illuminated.

    2000-2003 Tahoe, Suburban, Yukon, Yukon XL – DTC P0446 Set SES Illuminated

    General Motors 2005-08-01

  • Replace the EVAP vent solenoid.

    Replace EVAP vent solenoid.

    General Motors 2005-08-01

  • Do not replace the EVAP canister. The reference bulletin is 04-06-04-055.

    Don’t replace EVAP canister. 04-06-04-055

    General Motors 2005-08-01

Read every statement and its source →

Records

None among the records that can be opened now.

See all 0 records of this cause →

A cause or a result a complaint states is the owner’s view or what a dealer told them, not an established fact.