Skip to content
FaultCrate
日本語

This is an open preview: every record can be read without an account.

GMC Yukon 2000–2006

GMC YukonModel years 2000–2006

Change vehicle →
Clear the search
2 conditions added

Common on this vehicle:Loss of engine power, no accelerationWarning light

Record by record

3 records state a cause or a remedy. Each record is shown as short labels in the order fault → finding the cause → correction. Press a label to narrow to the records that state it.

Read the records one by one (3)

Known issuesDTCs P2108, P1516 and U0107 (do not replace the TAC module)1

  1. Manufacturer communication2006 GMC YUKON ・ 2006-07-19

    Throttle Body Codes P2108, P1516, U0107

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      THROTTLE BODY CODES P2108, P1516, AND U0107. *TT

      What the documents say to do

      DTCs P2108, P1516 and U0107 (do not replace the TAC module)

      Confirm

      • Perform the diagnostics for the DTCs, but delete the steps that involve replacing the TAC module.

      Caution

      • Do not replace the TAC module; the reference given is PIP 3812A.
    Read the sentences of the record
    Remedy
    THROTTLE BODY CODES P2108, P1516, AND U0107. *TT

ELECTRICAL SYSTEM2

  1. Manufacturer communication2005–2006 GMC YUKON DENALI ・ 2018-05-21

    Throttle Position Sensor Cover Replacement

    1. 1Fault

      • The malfunction indicator lamp (MIL) is illuminated with a Reduced Engine Power message displayed.
      • A scan tool may show DTC P2135: Throttle Position (TP) Sensor 1-2 Correlation set as Current or in History.

    2. 2Finding the cause

      Possible causes

      • The condition may be caused by the difference between TP Sensor 1 and TP Sensor 2 exceeding a calibrated value for more than 2 seconds.

      Steps to confirm (in the document’s order)

      1. After installing the new cover, if the scan tool TP Sensor 1 and 2 Agree/Disagree parameter displays Disagree, replace the throttle body assembly.
      2. If DTC P1516, P2101 and/or P2176 are set, replace the throttle body.

    3. 3Correction

      Repair

      1. Clean the throttle body bore and throttle plate with a clean shop towel and GM Top Engine Cleaner, P/N 1052626 (in Canada, P/N 993026), or ACDelco Upper Engine and Fuel Injector Cleaner, P/N 88861803, or an equivalent product.
      2. Remove the old TP sensor cover from the throttle body: grasp the cover, carefully lift it up and separate it from the throttle body.
      3. Tighten the throttle body fasteners to 89 lb in (= 10.1 N·m) (the text prints the metric value as "10 Y").
      4. Reprogram the ECM using the Service Programming System (SPS) with the latest calibration available on TIS2WEB.
      5. Perform the Throttle Learn Reset Procedure.

      Part numbers printed in the document

      The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

      Parts

      • Part number 19259452, Throttle Position (TP) Sensor Cover, quantity 1.

      Part numbers printed in the document

      The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

      Caution

      • Do not replace the throttle body; follow the procedure in the bulletin instead.
      • If the throttle body is dropped at any time during the procedure, abort the procedure and replace it with a new throttle body assembly.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：The Yukon entries are 2008-2011 GMC Canyon, Savana, Sierra, Sierra Denali and Yukon models (note: earlier Yukon model years are not listed).
    • Condition：The malfunction indicator lamp (MIL) is illuminated with a Reduced Engine Power message displayed.
    • Condition：A scan tool may show DTC P2135: Throttle Position (TP) Sensor 1-2 Correlation set as Current or in History.
    • Cause：The condition may be caused by the difference between TP Sensor 1 and TP Sensor 2 exceeding a calibrated value for more than 2 seconds.
    • Caution：Do not replace the throttle body; follow the procedure in the bulletin instead.
    • Repair：Clean the throttle body bore and throttle plate with a clean shop towel and GM Top Engine Cleaner, P/N 1052626 (in Canada, P/N 993026), or ACDelco Upper Engine and Fuel Injector Cleaner, P/N 88861803, or an equivalent product.
    • Repair：Remove the old TP sensor cover from the throttle body: grasp the cover, carefully lift it up and separate it from the throttle body.
    • Caution：If the throttle body is dropped at any time during the procedure, abort the procedure and replace it with a new throttle body assembly.
    • Confirm：After installing the new cover, if the scan tool TP Sensor 1 and 2 Agree/Disagree parameter displays Disagree, replace the throttle body assembly.
    • Confirm：If DTC P1516, P2101 and/or P2176 are set, replace the throttle body.
    • Repair：Tighten the throttle body fasteners to 89 lb in (= 10.1 N·m) (the text prints the metric value as "10 Y").
    • Repair：Reprogram the ECM using the Service Programming System (SPS) with the latest calibration available on TIS2WEB.
    • Repair：Perform the Throttle Learn Reset Procedure.
    • Parts：Part number 19259452, Throttle Position (TP) Sensor Cover, quantity 1.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This technical bulletin provides a procedure for replacing the throttle position sensor cover for concerns regarding a indicator lamp illuminated reduced power message displayed and DTC P2135 set.

  2. Manufacturer communication2003–2006 GMC YUKON ・ 2004-10-04

    Service Engine Soon Light and Reduced Engine Power (P1516)

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      SERVICE ENGINE SOON LIGHT AND REDUCED ENGINE POWER WITH A DIAGNOSTIC TROUBLE CODE P1516. DIAGNOSTIC TROUBLE CODES P0120, P0220, P1514, P1515, P1518 AND P2135 MAY ALSO BE PRESENT. *TT

    Read the sentences of the record
    Remedy
    SERVICE ENGINE SOON LIGHT AND REDUCED ENGINE POWER WITH A DIAGNOSTIC TROUBLE CODE P1516. DIAGNOSTIC TROUBLE CODES P0120, P0220, P1514, P1515, P1518 AND P2135 MAY ALSO BE PRESENT. *TT