GMC Yukon 2000–2006

Owner complaint2002 GMC YUKON ・ 2005-08-12

ABS engagement with loss of brakes at low speeds

1. 1Fault

   • ABS activates (at low speed and the like)
   ↓→

2. 2Finding the cause

   • Wheel Speed Sensor: failed
   ↓→

3. 3Correction

   • Hub Assembly: replaced (says it was fixed)
   • Wheel Speed Sensor: replaced (says it was fixed)

Manufacturer communication2000–2006 GMC YUKON DENALI ・ 2018-08-20

Light Duty Trucks: Grinding Noise in Park with 4WD Low

1. 1Fault

   • Noise
   • Light duty trucks with automatic transmission and 4 wheel drive may make a grinding/ratcheting noise when the transmission is shifted into park while the transfer case is in 4 wheel drive low (4LO) range.
   • The grind/ratchet noise lasts approximately one second.
   ↓→

2. 2Finding the cause

   Possible causes

   • When the transmission is shifted from drive or reverse into park with the transfer case in 4LO, the driveline unloads and turns the propeller shaft approximately 1/8 of a turn.
   • The gear reduction in the transfer case makes the transmission output shaft turn faster than the parking pawl will hold, so the parking pawl grinds/ratchets until the output shaft stops.
   ↓→

3. 3Correction

   Caution

   • This should be considered characteristic of 4 wheel drive vehicles operated in 4LO.
   • Replacing transmission, transfer case and/or driveline components will not resolve the concern; shifting into park with the transfer case in the 4HI or 2HI range is recommended.

Recall2005 GMC YUKON ・ —

Automatic Transmission Shift Lever Position Indicator Illumination Recall

1. 1Fault

   • Under certain starting conditions the shift lever position indicator in the instrument panel cluster may not illuminate; on later start-ups the condition may or may not recur.
   • If the indicator does not illuminate, the driver may not know which gear is selected and the vehicle may move in an unintended direction, possibly injuring people outside the vehicle.
   ↓→

2. 2Finding the cause

   • Shift Lever Position Indicator: failed

   Possible causes

   • The PRNDL indicator behavior is induced only by a very specific battery voltage waveform and depends on vehicle level characteristics, while the vehicle otherwise operates normally.
   • The "blank PRNDL" anomaly appeared at the assembly plants after interim 2005 model year instrument panel cluster revisions that began on January 31, 2005.
   ↓→

3. 3Correction

   • Instrument Panel Cluster: reprogrammed

   Repair

   1. Dealers are to reprogram the instrument panel cluster.
   2. Prepare the vehicle for instrument panel cluster (IPC) reprogramming, then program the IPC using TIS data version 2.25.

   Parts

   • No parts are required for this recall.

   Caution

   • The service calibration is in Techline Information System (TIS) data version 2.25 and on TIS CD-ROM version 3.
   • A later dealer message says TIS Data 2.50 has been released, so dealers no longer need to contact the Techline Customer Support Center (TCSC) for a VCI number to access the calibration.
   • Vehicles with manual transmissions are not involved in this recall and need no further action.

Owner complaint2003 GMC YUKON DENALI ・ 2012-02-12

Loss of power without warning while driving at highway speed

1. 1Fault

   WE WERE DRIVING AT HIGHWAY SPEED AND LOST POWER WITH NO WARNING.

   ↓→

2. 2Finding the cause

   WITHOUT CLEANING THE THROTTLE BODY OTHERS WILL HAVE THIS PROBLEM TOO.

   ↓→

3. 3Correction

   • Throttle Body: cleaned

Owner complaint2003 GMC YUKON ・ 2006-01-03

Screeching noise from rear during turns and four-wheel drive engagement

1. 1Fault

   • Noise
   ↓→

2. 2Finding the cause

   THIS COULD POSSIBLY BE THE CULPRIT OF THE SCREECHING NOISE WHEN TURNING.

   ↓→

3. 3Correction

   • Four Wheel Drive System: repaired

Owner complaint2005 GMC YUKON DENALI ・ 2016-04-09

Accelerator stops working during acceleration

1. 1Fault

   • Loss of engine power, no acceleration
   • Traction control message
   ↓→

2. 2Finding the cause

   Not stated

   ↓→

3. 3CorrectionNot repaired

   TO DATE, NO ONE HAS BEEN ABLE TO FIX THE PROBLEM.

Owner complaint2005 GMC YUKON DENALI ・ 2005-03-25

Driver's side rear tire came off while driving at low speed in school zone

1. 1Fault

   I WAS ONLY DRIVING BETWEEN 10-15MPH (= 16.1–24.1 km/h).

   ↓→

2. 2Finding the cause

   • Wheel Stud: broken
   ↓→

3. 3Correction

   Not stated

Manufacturer communication2000–2006 GMC YUKON DENALI ・ 2024-08-15

Transmission Core Damage Prevention Notice

1. 1Fault

   • GM is receiving many cracked or broken transmission cores at the remanufacturing facilities, and the damage makes them unusable for remanufacturing.
   ↓→

2. 2Finding the cause

   • Transmission Core: broken
   ↓→

3. 3Correction

   GM is receiving damaged (cracked or broken) transmission cores returned to the reman facilities. The damage is being caused either in the removal process by the technician, or inadequate packaging or shipping. This bulletin advises the dealers to be more careful not to damage the transmissions during removal and to package the core properly for return.

Manufacturer communication2005–2006 GMC YUKON DENALI ・ 2024-06-07(3 earlier editions of this document folded here)

Water or Ethylene Glycol in Transmission Fluid

1. 1Fault

   • Vibration or shudder
   • Water or ethylene glycol in ATF changes the friction of the clutches, frequently causing shudder during engagement or gear changes, especially during torque converter clutch engagement.
   ↓→

2. 2Finding the cause

   Steps to confirm (in the document’s order)

   1. An indication of water in the ATF: ATF blowing out of the transmission vent tube.
   2. The ATF may appear cloudy or, with extreme contamination, look like a strawberry milkshake.
   3. There may be visible water in the oil pan or a milky white substance inside the pan area.
   4. Spacer plate gaskets appear swollen or wrinkled in areas where they are not compressed.
   5. If water is found in the ATF and its source is not identified, or a leaking in-radiator transmission oil cooler is suspected, a simple and quick test kit that detects ethylene glycol in ATF is available.

   1 more points
   ↓→

3. 3Correction

   Repair

   1. If water or coolant is found in the transmission, all rubber-type seals, all composition-faced clutch plates and/or bands, all nylon parts and the torque converter must be replaced.
   2. Thoroughly clean and rebuild the transmission, using new gaskets and oil filter.
   3. Flush and flow check the transmission oil cooler using J-45096.
   4. Thoroughly inspect the engine cooling system and hoses and clean/repair as necessary.

Manufacturer communication2000–2006 GMC YUKON ・ 2022-10-17

Torque Converter Bolt Removal Warning

1. 1Fault

   • Noise
   • Noise from underneath a vehicle equipped with an automatic transmission.
   ↓→

2. 2Finding the cause

   Possible causes

   • Running the engine with those bolts removed may damage the pilot on the front of the torque converter, the pilot hole in the end of the crankshaft, or both.

   Steps to confirm (in the document’s order)

   • Use chassis ears to isolate the component or assembly that is the loudest source of the noise.
   ↓→

3. 3Correction

   Caution

   • Do not remove the flex plate to torque converter bolts, push the converter back toward the transmission and start the engine to tell whether the noise is from the engine or the transmission.

Owner complaint2003 GMC YUKON ・ 2022-10-06

Engine stalls with battery warning light and brake pedal vibration at various speeds

1. 1Fault

   • Stalls or shuts off
   • Vibration or shudder
   • Warning light
   ↓→

2. 2Finding the cause

   Not stated

   ↓→

3. 3CorrectionNot repaired

   The vehicle had yet to be repaired.

Manufacturer communication2000–2006 GMC YUKON DENALI ・ 2022-09-19

Flexplate and Torque Converter Separation Warning

1. 1Fault

   • Noise
   • A noise comes from underneath a vehicle equipped with an automatic transmission.
   • The technician may find that the noise comes from the bell housing area.
   ↓→

2. 2Finding the cause

   Possible causes

   • Running the engine with those bolts removed may damage the pilot on the front of the torque converter, the pilot hole in the end of the crankshaft, or both.

   Steps to confirm (in the document’s order)

   • Use chassis ears to isolate the component or assembly that is the loudest source of the noise.
   ↓→

3. 3Correction

   Caution

   • Do not separate the torque converter from the flex plate.
   • Do not remove the flex plate to torque converter bolts, push the converter back and start the engine to tell whether the noise is from the engine or the transmission.

Manufacturer communication2005–2006 GMC YUKON DENALI ・ 2024-02-17(6 earlier editions of this document folded here)

Warranty Admin Service Bulletin - Engine/Transmission Replacement

1. 1Fault

   • Under GM Service Policies and Procedures, dealers are to perform the most cost economical repair when deciding between assembly repair and replacement.
   ↓→

2. 2Finding the cause

   Not stated

   ↓→

3. 3Correction

   This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.

Manufacturer communication2000–2006 GMC YUKON DENALI ・ 2024-02-02

Piston Installation Procedure

1. 1Fault

   Not stated

   ↓→

2. 2Finding the cause

   Steps to confirm (in the document’s order)

   • Refer to the Engine Mechanical Specification in SI for the correct bore and piston specification.
   ↓→

3. 3Correction

   Repair

   1. When installing a piston into a cylinder, use a ring compressor sleeve or equivalent for best results.
   2. Choose a sleeve with a smooth radius that tapers down to the specific bore size.
   3. Select a size only slightly bigger than the piston diameter and not larger than the cylinder bore diameter.

   Caution

   • If a sleeve is unavailable in the needed size, a universal ring compressor will work but is more difficult to use.

Manufacturer communication2004–2006 GMC YUKON DENALI ・ 2023-11-22

Vibration Analysis Worksheet Service Bulletin

1. 1Fault

   • Vibration or shudder
   ↓→

2. 2Finding the cause

   Steps to confirm (in the document’s order)

   1. When diagnosing vibration, use the worksheet together with the Vibration Analysis - Road Testing procedure in the service information.
   2. Place the sensor where the vibration is felt: on the seat track for a seat complaint, on the steering column for a steering wheel complaint.
   3. Moving the sensor to other areas, look for the same Hz reading with the greatest amplitude.
   4. If a system balance was attempted and the vibration remains, check ring gear backlash at each tooth; readings should not vary more than 0.050 mm (0.002 in).
   5. Aluminum wheel/tire runout measured on the vehicle: maximum 0.030 in (.762 mm).

   2 more points
   ↓→

3. 3Correction

   This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns.

Manufacturer communication2000–2006 GMC YUKON DENALI ・ 2023-09-26

Normal Transmission Shift and Throttle Response Delay

1. 1Fault

   • Loss of engine power, no acceleration
   • A sag or hesitation may be noticed when coasting at low speeds of less than 24 km/h (15 mph) with a closed throttle and then aggressively applying the throttle.
   • With an automatic transmission, after a hard complete stop with a closed throttle immediately followed by an aggressive throttle opening, the downshifts may not be completed by the time the throttle is opened.
   • A sag or hesitation may also be noticed while cruising at highway speeds and then aggressively increasing the throttle, forcing a down-shift.
   ↓→

2. 2Finding the cause

   Possible causes

   • In this maneuver the throttle blade is opened slowly for up to 0.7 seconds, even though the accelerator is applied aggressively, to help minimize driveline lash and clunking.
   • As a result, approximately 0.5 seconds of zero torque may be commanded to allow the shift to first gear to occur.
   ↓→

3. 3Correction

   Caution

   • All of these conditions are a result of Torque Management and should be considered normal; no repairs should be attempted.

Manufacturer communication2005–2006 GMC YUKON DENALI ・ 2022-12-06(2 earlier editions of this document folded here)

Engine and Transmission Assembly Replacement Under Warranty Policy

1. 1Fault

   • The document gives the policies for U.S. dealers on engine and transmission assembly replacement under warranty, policy or Customer Enthusiasm.
   ↓→

2. 2Finding the cause

   Not stated

   ↓→

3. 3Correction

   This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.

Manufacturer communication2003–2006 GMC YUKON DENALI ・ 2022-10-11(1 earlier editions of this document folded here)

OEM and Remanufactured Engine/Transmission ID Notification

1. 1Fault

   Not stated

   ↓→

2. 2Finding the cause

   Steps to confirm (in the document’s order)

   1. The engine bar code tag could be on a rocker arm cover, on the ends of a cylinder head, or on the oil pan or oil rail area of the engine.
   2. All remanufactured engines have a label on the right or left side of the block.
   3. On the 4.8L/5.3L/6.0L/6.2L (Gen III/Gen IV) engines the remanufactured engine label is on the left side of the block.
   ↓→

3. 3Correction

   Caution

   • If a piston must be replaced, measure the cylinder before ordering; most of these engines have oversized cylinders, and oversized piston ring packs are not available for service.
   • If crankshaft bearings must be replaced, measure the crankshaft before ordering; a crankshaft that has been turned must be replaced, together with all new standard size bearings.

Owner complaint2001 GMC YUKON ・ 2003-04-01

Cruise control failure and component replacements

1. 1Fault

   Not stated

   ↓→

2. 2Finding the cause

   • Stop Lamp Circuit: electrical fault
   ↓→

3. 3Correction

   • Powertrain Control Module: replaced
   • Serpentine Belt: replaced
   • Starter: replaced

Manufacturer communication2006 GMC YUKON DENALI ・ 2020-12-07

Aftermarket ALDL/DLC Interface Devices - Diagnostic Concerns

1. 1Fault

   • Gauge or instrument fault
   • Warning light
   • C0561 (general documents only)
   • U0100 (general documents only)
   • U0101 (general documents only)
   • U186B (general documents only)
   • U1862 (general documents only)
   • The radio may not shut off after the vehicle is shut down, and bus or LAN traffic may stay active, leading to a discharged battery.
   • C0561 may be stored in the EBCM, leading to a traction control issue, and there may be no high speed LAN communication with various communication U-codes.
   • The SES, MIL or CEL light may be set with numerous communication DTCs such as U0100, U0101, U186B and U1862.
   • The transmission may not shift for one key cycle (TCM in default mode), and gauge readings may be erratic or displays may flicker.
   ↓→

2. 2Finding the cause

   Possible causes

   • Monitoring devices and other electronic accessories such as aftermarket cruise control or police speed checking devices (RADAR or LIDAR) may cause one or more of the listed concerns.
   • Many of the problems could be caused by an open connection on the HSCAN bus: a device that connects to only one CAN + causes bus errors and erratic ECU behavior.

   Steps to confirm (in the document’s order)

   • If normal diagnostics find no root cause, check for a device plugged into the ALDL or Data Link Connector (DLC) for tracking and/or maintenance interval scheduling.
   ↓→

3. 3Correction

   Repair

   1. If SI diagnostics do not identify the source and the device is available, try to duplicate the condition, then remove the device to see whether the condition is eliminated.
   2. If removing the DLC interface device resolves the concern, tell the customer the result and that they should work with the device's supplier for further resolution.

   Caution

   • The customer may remove the device for use in another vehicle while theirs is in for service.
   • Some devices carry a second DLC connector, with the device and the rest of the harness hidden out of sight, so the technician may not notice that the diagnostic connector is not in the factory location.

Manufacturer communication2003–2006 GMC YUKON DENALI ・ 2021-04-20

Engine and Transmission Identification

1. 1Fault

   Not stated

   ↓→

2. 2Finding the cause

   Not stated

   ↓→

3. 3Correction

   OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification

Manufacturer communication2006 GMC YUKON DENALI ・ 2018-05-29

Service Information Bulletin: Assembly Replacement vs. Repair Process

1. 1Fault

   • All service agents must still contact the PQC for Allison transmission replacement, specified Duramax diesel engine replacement and any current restrictions or exchanges.
   ↓→

2. 2Finding the cause

   Not stated

   ↓→

3. 3Correction

   This informational bulletin provides a process to the service agents that are not required to contact PQC, to determine when to replace a assembly as opposed to repairing and if an engine or transmission is being returned, that it has all the information in relation to that part being returned.

Manufacturer communication2003–2006 GMC YUKON DENALI ・ 2018-06-04

Automatic Transmission Oil Cooler Flow Test Essential Tool J-45096

1. 1Fault

   • In flow mode, an electronic flow meter measures the flow capability of the ATF oil cooling system.
   ↓→

2. 2Finding the cause

   Steps to confirm (in the document’s order)

   1. On the 4L60-E, the cooler feed (exiting the transmission) is the bottom connector and the return (entering the transmission) is the top connector; J-35944-200 may be required.
   2. On the 4L80-E, the cooler feed is the front connector and the return is the rear connector; J-35944-200 may be required.
   ↓→

3. 3Correction

   Repair

   • For the flow test and flush procedure, refer to Automatic Transmission Oil Cooler Flushing and Flow Test J-45096 in SI.

   Caution

   • Insufficient oil flow through the ATF oil cooling system will cause premature transmission failure; the required minimum flow rate depends directly on the supply oil temperature.
   • The oil in the supply vessel must be 18°C (65°F) or warmer for the J-45096 to operate.
   • Labor operations that remove the transmission for an internal repair or torque converter replacement include time to flow check and flush the transmission oil cooler system.
   • A flow test and flush uses between 4.7-7.5 L (5-8 qts) of DEXRON VI transmission fluid.

Manufacturer communication2005–2006 GMC YUKON DENALI ・ 2018-06-04

Informational Bulletin Revision 09-07-30-018C

1. 1Fault

   • A revised process is being implemented for automatic transmission internal repair claim documentation and warranty claim submission.
   ↓→

2. 2Finding the cause

   Not stated

   ↓→

3. 3Correction

   This informational bulletin provides a revision for 09-07-30-018C to add the 2014 model year and update the Labor Operation.