Skip to content
FaultCrate
日本語

This is an open preview: every record can be read without an account.

GMC Yukon 2000–2006

GMC YukonModel years 2000–2006

Change vehicle →
Clear the search
2 conditions added

The vehicle (where a record says)

A record is under an engine, a drive or a series only where it says so: the characters of the vehicle identification number filed with a complaint, its text, or what its document says it applies to. A record that does not say is kept as "not stated". The filed numbers and the documents do not tell 4WD from AWD.

Common on this vehicle:NoiseWarning lightVibration or shudderLeakShifting faultLoss of engine power, no accelerationGauge or instrument faultStalls or shuts off

Record by record

6 records state a cause or a remedy. Each record is shown as short labels in the order fault → finding the cause → correction. Press a label to narrow to the records that state it.

Work done

How it is said to have ended

  • says it came back2

A ribbon is as wide as the records that state both of its ends (only the commonest are drawn). A record that names several symptoms or components runs through each. Orange is records that say the fault came back or was not fixed. Results come from owners’ reports only; one that does not say is “result not stated”. None of this is a likelihood of a cause or a rate at which work succeeds.

Read the records one by one (6)

ELECTRICAL SYSTEM3

  1. Manufacturer communication2005–2006 GMC YUKON DENALI ・ 2018-05-21

    Throttle Position Sensor Cover Replacement

    1. 1Fault

      • The malfunction indicator lamp (MIL) is illuminated with a Reduced Engine Power message displayed.
      • A scan tool may show DTC P2135: Throttle Position (TP) Sensor 1-2 Correlation set as Current or in History.

    2. 2Finding the cause

      Possible causes

      • The condition may be caused by the difference between TP Sensor 1 and TP Sensor 2 exceeding a calibrated value for more than 2 seconds.

      Steps to confirm (in the document’s order)

      1. After installing the new cover, if the scan tool TP Sensor 1 and 2 Agree/Disagree parameter displays Disagree, replace the throttle body assembly.
      2. If DTC P1516, P2101 and/or P2176 are set, replace the throttle body.

    3. 3Correction

      Repair

      1. Clean the throttle body bore and throttle plate with a clean shop towel and GM Top Engine Cleaner, P/N 1052626 (in Canada, P/N 993026), or ACDelco Upper Engine and Fuel Injector Cleaner, P/N 88861803, or an equivalent product.
      2. Remove the old TP sensor cover from the throttle body: grasp the cover, carefully lift it up and separate it from the throttle body.
      3. Tighten the throttle body fasteners to 89 lb in (= 10.1 N·m) (the text prints the metric value as "10 Y").
      4. Reprogram the ECM using the Service Programming System (SPS) with the latest calibration available on TIS2WEB.
      5. Perform the Throttle Learn Reset Procedure.

      Part numbers printed in the document

      The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

      Parts

      • Part number 19259452, Throttle Position (TP) Sensor Cover, quantity 1.

      Part numbers printed in the document

      The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

      Caution

      • Do not replace the throttle body; follow the procedure in the bulletin instead.
      • If the throttle body is dropped at any time during the procedure, abort the procedure and replace it with a new throttle body assembly.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：The Yukon entries are 2008-2011 GMC Canyon, Savana, Sierra, Sierra Denali and Yukon models (note: earlier Yukon model years are not listed).
    • Condition：The malfunction indicator lamp (MIL) is illuminated with a Reduced Engine Power message displayed.
    • Condition：A scan tool may show DTC P2135: Throttle Position (TP) Sensor 1-2 Correlation set as Current or in History.
    • Cause：The condition may be caused by the difference between TP Sensor 1 and TP Sensor 2 exceeding a calibrated value for more than 2 seconds.
    • Caution：Do not replace the throttle body; follow the procedure in the bulletin instead.
    • Repair：Clean the throttle body bore and throttle plate with a clean shop towel and GM Top Engine Cleaner, P/N 1052626 (in Canada, P/N 993026), or ACDelco Upper Engine and Fuel Injector Cleaner, P/N 88861803, or an equivalent product.
    • Repair：Remove the old TP sensor cover from the throttle body: grasp the cover, carefully lift it up and separate it from the throttle body.
    • Caution：If the throttle body is dropped at any time during the procedure, abort the procedure and replace it with a new throttle body assembly.
    • Confirm：After installing the new cover, if the scan tool TP Sensor 1 and 2 Agree/Disagree parameter displays Disagree, replace the throttle body assembly.
    • Confirm：If DTC P1516, P2101 and/or P2176 are set, replace the throttle body.
    • Repair：Tighten the throttle body fasteners to 89 lb in (= 10.1 N·m) (the text prints the metric value as "10 Y").
    • Repair：Reprogram the ECM using the Service Programming System (SPS) with the latest calibration available on TIS2WEB.
    • Repair：Perform the Throttle Learn Reset Procedure.
    • Parts：Part number 19259452, Throttle Position (TP) Sensor Cover, quantity 1.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This technical bulletin provides a procedure for replacing the throttle position sensor cover for concerns regarding a indicator lamp illuminated reduced power message displayed and DTC P2135 set.

  2. Owner complaint2003 GMC YUKON ・ 2017-08-28

    Reduced engine power warning and deceleration while driving

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      Not stated

    Read the sentences of the record
    Fault
    WHILE DRIVING APPROXIMATELY 50 MPH (= 80.5 km/h), THE VEHICLE EXPERIENCED INDEPENDENT DECELERATION AND THE REDUCED ENGINE POWER WARNING INDICATOR ILLUMINATED.
    Inspection
    THE VEHICLE WAS PREVIOUSLY TAKEN TO AN INDEPENDENT MECHANIC WHO DIAGNOSED THAT THE FUEL PUMP, SPARK PLUGS, TRANSMISSION, AND ALTERNATOR NEEDED TO BE REPLACED.
    Outcome
    THE VEHICLE WAS REPAIRED, BUT THE FAILURE RECURRED.

  3. Manufacturer communication2005–2006 GMC YUKON DENALI ・ 2009-06-02

    Intermittent MIL/DTC P2138 with Reduced Engine Power

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

    Read the sentences of the record
    Remedy
    GENERAL MOTORS: INTERMITTENT MIL/SES/ DTC P2138 WITH REDUCED ENGINE POWER (REPAIR INSTRUMENT PANEL (IP) TO BODY HARNESS CONNECTOR). 2005-08 GM PASSENGERS CARS/LIGHT DUTY TRUCKS (INCL. SATURNS). *PE UPDATED 11/5/10. *PE UPDATED 4/4/11. *PE UPDATED 2/3/16. *PE

ENGINE1

  1. Owner complaint2003 GMC YUKON DENALI ・ 2014-07-23

    Vehicle decelerated and stalled with reduced engine power indicator illuminated

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

    Read the sentences of the record
    Fault
    THE CONTACT STATED THAT THE VEHICLE DECELERATED AND STALLED. (1 more)

ENGINE AND ENGINE COOLING1

  1. Manufacturer communication2000–2006 GMC YUKON DENALI ・ 2023-09-26

    Normal Transmission Shift and Throttle Response Delay

    1. 1Fault

      • A sag or hesitation may be noticed when coasting at low speeds of less than 24 km/h (15 mph) with a closed throttle and then aggressively applying the throttle.
      • With an automatic transmission, after a hard complete stop with a closed throttle immediately followed by an aggressive throttle opening, the downshifts may not be completed by the time the throttle is opened.
      • A sag or hesitation may also be noticed while cruising at highway speeds and then aggressively increasing the throttle, forcing a down-shift.

    2. 2Finding the cause

      Possible causes

      • In this maneuver the throttle blade is opened slowly for up to 0.7 seconds, even though the accelerator is applied aggressively, to help minimize driveline lash and clunking.
      • As a result, approximately 0.5 seconds of zero torque may be commanded to allow the shift to first gear to occur.

    3. 3Correction

      Caution

      • All of these conditions are a result of Torque Management and should be considered normal; no repairs should be attempted.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：GM passenger cars and trucks, model years 2000 to 2024.
    • Condition：A sag or hesitation may be noticed when coasting at low speeds of less than 24 km/h (15 mph) with a closed throttle and then aggressively applying the throttle.
    • Cause：In this maneuver the throttle blade is opened slowly for up to 0.7 seconds, even though the accelerator is applied aggressively, to help minimize driveline lash and clunking.
    • Condition：With an automatic transmission, after a hard complete stop with a closed throttle immediately followed by an aggressive throttle opening, the downshifts may not be completed by the time the throttle is opened.
    • Cause：As a result, approximately 0.5 seconds of zero torque may be commanded to allow the shift to first gear to occur.
    • Condition：A sag or hesitation may also be noticed while cruising at highway speeds and then aggressively increasing the throttle, forcing a down-shift.
    • Caution：All of these conditions are a result of Torque Management and should be considered normal; no repairs should be attempted.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay.

POWER TRAIN1

  1. Owner complaint2005 GMC YUKON DENALI ・ 2016-04-09

    Accelerator stops working during acceleration

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3CorrectionNot repaired

      TO DATE, NO ONE HAS BEEN ABLE TO FIX THE PROBLEM.

    Read the sentences of the record
    Fault
    WHEN ACCELERATING FROM A STOP OR ANYTIME WHEN TRAVELING BETWEEN 1- 2-3RD GEARS, THE ACCELERATOR WILL SUDDENLY STOP WORKING AND THE "TRACTION ACTIVE" LIGHT WILL COME ON. (4 more)
    Remedy
    TO DATE, NO ONE HAS BEEN ABLE TO FIX THE PROBLEM.
    Consequence
    THE SCARY THING ABOUT THIS IS THAT WHEN YOU ARE ACCELERATING FROM A STOP AND OTHER CARS ARE ACCELERATING BEHIND YOU, THEY DON'T ANTICIPATE THAT YOU WILL STOP ACCELERATING (THE BRAKE LIGHTS DO NOT COME ON), THEREFORE, THEY ALMOST REAR END ME.