Skip to content
FaultCrate
日本語

This is an open preview: every record can be read without an account.

GMC Yukon 2000–2006

GMC YukonModel years 2000–2006

Change vehicle →
Clear the search
Add conditions (optional: symptom, model year, system, warning display, trouble code, kind of record)

Common on this vehicle:

issueRecords under no cardRemovecauseRoller RockerRemove

Record by record

4 records state a cause or a remedy. Each record is shown as short labels in the order fault → finding the cause → correction. Press a label to narrow to the records that state it.

Component named as the cause

Work done

A ribbon is as wide as the records that state both of its ends (only the commonest are drawn). A record that names several symptoms or components runs through each. Orange is records that say the fault came back or was not fixed. Results come from owners’ reports only; one that does not say is “result not stated”. None of this is a likelihood of a cause or a rate at which work succeeds.

Read the records one by one (2)

ENGINE1

  1. Manufacturer communication2000–2006 GMC YUKON DENALI ・ 2020-08-10(2 earlier editions of this document folded here)

    Needle Bearings in Roller Rockers During Oil Change

    1. 1Fault

      • Needle bearings may be found in the oil pan during an oil change.

    2. 2Finding the cause

      Steps to confirm (in the document’s order)

      1. If roller rocker arm needle bearings are found during an oil change, inspect all the roller rocker arms.
      2. There should be 66 bearings, 33 a side.

    3. 3Correction

      Repair

      1. Replace only the broken roller rocker arm; the remaining roller rocker arms need not be replaced.
      2. Needle bearings may also be in the cylinder head oil drains; clean the oil drains to retrieve them.

      Caution

      • The oil pan does not need to be removed: the needle bearing is larger than the oil pump pickup screen mesh and cannot be pulled into the oil pump.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to all brands and models, 2000 - 2021, with V6 or V8 push rod engines with roller rockers.
    • Condition：Needle bearings may be found in the oil pan during an oil change.
    • Confirm：If roller rocker arm needle bearings are found during an oil change, inspect all the roller rocker arms.
    • Repair：Replace only the broken roller rocker arm; the remaining roller rocker arms need not be replaced.
    • Repair：Needle bearings may also be in the cylinder head oil drains; clean the oil drains to retrieve them.
    • Confirm：There should be 66 bearings, 33 a side.
    • Caution：The oil pan does not need to be removed: the needle bearing is larger than the oil pump pickup screen mesh and cannot be pulled into the oil pump.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.

EQUIPMENT1

  1. Manufacturer communication2000–2006 GMC YUKON DENALI ・ 2017-03-21

    Needle Bearings in Oil During Service

    1. 1Fault

      Not stated

    2. 2Finding the cause

    3. 3Correction

    Read the sentences of the record
    Remedy
    THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT FINDING NEEDLE BEARINGS DURING AN OIL CHANGE. TECHNICIAN WILL GAIN ACCESS TO THE ROLLER ROCKERS TO INSPECT THEM. ONLY REPLACE THE ROLLER ROCKER THAT IS MISSING NEEDLE BEARINGS. BE SURE TO CLEAN THE OIL DRAINS TO RETRIEVE THE NEEDLE BEARINGS. EACH ROLLER ROCKER HAS 66 BEARINGS.

Showing 2 of the 4 you can open. Narrow the search to see the rest.