Skip to content
FaultCrate
日本語

This is an open preview: every record can be read without an account.

Selected vehicle: 2006 · GMC Yukon XL Denali

Change vehicle →

← Back to cases

Source reference 11019072

Manufacturer communication — 2006 GMC YUKON DENALI XL

Fitment confirmedReporter type: ManufacturerUNKNOWN OR OTHER

Relation to the target vehicle

  • The source's vehicle field includes the trim.
Model year
Match 2006 — Source vehicle field
Model
Match YUKON DENALI XL — Source vehicle field
Trim
Match Denali — Source vehicle field

What the manufacturer’s document says

PIT5074R ・ information ・ for GM vehicles in general

Applies to

  • All brands and models, model years 2005 - 2026.

    the passage
    2005 - 2026 All All All All

Finding the cause

Possible causes

  • In intermittent electrical concerns, terminal tension is one of the main culprits, especially with very small terminals.

    the passage
    When diagnosing an intermittent electrical concern terminal tension is one of the main culprits, especially when working with very small terminals.

Steps to confirm (in the document’s order)

  1. The J-35616-64B is the latest test probe for checking tension or probing the .64 series terminals.

    the passage
    The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals.

  2. The EL-35616-58 is the latest test probe for checking terminal tension on the Mini .50 series terminals.

    the passage
    the EL-35616-58 is the latest test probe released for checking terminal tension on the Mini .50 series terminals.

Correction

Repair

  1. This terminal may also be used to make jumper wires, for example to jumper the High Speed LAN circuits together in order to bypass a module, for testing only.

    the passage
    This terminal may also be used to make jumper wires; example: to jumper the High Speed LAN circuits together in order to bypass a module for testing only.

  2. Use crimping tool J-38125-641 with jaw "H" for 22 ga wire, "J" for 20 ga wire, or "K" for 18 ga.

    the passage
    Use crimping tool J-38125-641 and jaw "H" for 22ga wire, "J" for 20 ga wire, or "K" for 18 ga.

Parts

  • The test probe terminal is in the terminal repair kit (J-38125-620H), in Lear Tray 7, part number 963716-2.

    the passage
    The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2 shown below.

  • The .64 test probe terminal is also available already connected to a lead (a terminated lead) as GM part number 13505346.

    the passage
    Another option is to order the .64 test probe terminal already connected to a lead/wire called a terminated lead. The GM part number is 13505346, which can be ordered through your normal GM CCA parts channel.

Part numbers printed in the document

The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

Caution

  • Always refer to the Connector End View in Service Information to determine the correct test probe to use.

    the passage
    Note: Always refer to the Connector End View in Service Information for the latest information on determining the correct test probe to use.

  • If the terminal end of the J-35616-64B is bent, damaged, worn or broken, it should not be used, and a replacement test probe or terminal should be obtained.

    the passage
    If the terminal end of the J-35616-64B is bent, damaged, worn or broken, it should not be used and a replacement test probe or terminal should be obtained from GM Tools

  • No male terminals are available because these terminals are currently used for module connections only; replacement female terminals are available for harness side repairs.

    the passage
    No male terminals are available as these terminals are currently used for module connections only. Replacement female terminals are available for harness side repairs.

What is needed

Parts and materials
Not stated
Labor time
Not stated
Special tools
  • Test probes J-35616-64B (checking tension or probing .64 series terminals) and EL-35616-58 (checking terminal tension on Mini .50 series terminals)(the document covers model year 2005 onward)
Scan tool
Not stated

Only what the technical documents state. "Not stated" does not mean not needed.

Compiled by reading the full text of the document; each point stands on the passage shown. Check the document itself, linked below, before working on a vehicle.

Stated content

  1. Communication summary

    本予備情報通知は、J-35616-64B及びMini 50端子テストプローブ、交換用端子及び処理済みリードの使用に関する情報を整備士に提供するものである。 Machine translation (unreviewed)

    This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini 50 terminal test probe, replacement terminals, and terminated leads.
    Go to this passage in the original

Source

Source
NHTSA Manufacturer Communications
Source reference
11019072
Received by source
2025-06-04
Incident date
Unknown

Open original text and sourceOpen the provider's page (external)

Manufacturer communication 11019072 — 2006 GMC YUKON DENALI XL | FaultCrate