Skip to content
FaultCrate
日本語Open preview: everything readable

This is an open preview: every record can be read without an account. The details of the plans are in preparation.

GMC Yukon XL 2000–2006

GMC Yukon XLModel years 2000–2006

Change vehicle →
Clear the search
1 conditions added

The vehicle (where a record says)

A record is under an engine, a drive or a series only where it says so: the characters of the vehicle identification number filed with a complaint, its text, or what its document says it applies to. A record that does not say is kept as "not stated". The filed numbers and the documents do not tell 4WD from AWD.

Common on this vehicle:Gauge or instrument faultWarning lightCorrosion or rustNoiseLeakReduced brakingStalls or shuts offLoss of engine power, no acceleration

Record by record

54 records state a cause or a remedy. Each record is shown as short labels in the order fault → finding the cause → correction. Press a label to narrow to the records that state it.

Symptom

Component named as the cause

Work done

How it is said to have ended

  • says it was fixed2
  • says it held for a while5
  • says it came back8
  • says it did not fix it6
  • result not stated4

A ribbon is as wide as the records that state both of its ends (only the commonest are drawn). A record that names several symptoms or components runs through each. Orange is records that say the fault came back or was not fixed. Results come from owners’ reports only; one that does not say is “result not stated”. None of this is a likelihood of a cause or a rate at which work succeeds.

Read the records one by one (34)

Known issuesCrankshaft position sensor may work intermittently or fail (8.1L V8) - recall 07V-5213

  1. Recall2001 GMC YUKON XL ・ 2007-11-09

    Crankshaft Position Sensor Failure Recall

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      Not stated

      What the documents say to do

      Crankshaft position sensor may work intermittently or fail (8.1L V8) - recall 07V-521

      Repair

      1. Dealers replace the crankshaft position sensor.
      2. As the remedy, an improved CKP is installed.

      Caution

      • All of the surveyed consumers noted multiple stalling events before the CKP was properly diagnosed and replaced.
    Read the sentences of the record
    Cause
    On certain vehicles equipped with an 8.1L engine, the crankshaft position sensor may fail. If the sensor operates intermittently, the Service Engine Soon (SES) light may illuminate and the vehicle may run rough. In addition, the engine may stall, and if so, may re-start immediately or after a cool-down period. If the sensor becomes inoperable permanently, the engine will quit running and will not re-start. Engine stalling would result in lost propulsion which, in conjunction with traffic and road conditions, and the driver's reactions, could increase the risk of a crash. Correction: Dealers will replace the crankshaft position sensor.

  2. Owner complaint2001 GMC YUKON XL 2500 ・ 2009-12-03

    Engine stalling intermittently due to crank position sensor issue

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

    Read the sentences of the record
    Fault
    THE CRANK CASE POSITION SENSOR SHUTS ON AND OFF INTERMITTENTLY WHICH CAUSED THE ENGINE TO STALL AND IT MAY NOT RESTART IMMEDIATELY.
    Cause
    THE FAILURE IS RELATED TO NHTSA#07V521000 AND GM RECALL# 06083, ENGINE AND ENGINE COOLING.
    Remedy
    A LOCAL MECHANIC REPAIRED THE TRANSMISSION AT FOR LESS THAN $800.
    Inspection
    A DIFFERENT AUTHORIZED DEALER PERFORMED A DIAGNOSTIC TEST AND STATED THAT THE CRANK SHAFT POSITION SENSOR NEEDED TO BE REPLACED.

  3. Owner complaint2001 GMC YUKON XL 2500 ・ 2008-04-25

    Engine stalled and lost power steering while driving 35 MPH at 82,000 miles

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

    Read the sentences of the record
    Fault
    WHILE DRIVING 35 MPH (= 56.3 km/h), THE VEHICLE SUDDENLY STALLED AND LOST POWER STEERING.
    Remedy
    HE DROVE THE VEHICLE TO THE DEALER AND THEY REPLACED THE CRANKSHAFT POSITION SENSOR AND THERE HAD BEEN NO FURTHER OCCURRENCES.

Known issuesEngine fuel rail crossover tube retainer screws may break (5.3L RPO L59) - recall 04V-3762

  1. Recall2005 GMC YUKON XL ・ 2004-02-08

    Engine Fuel Rail Crossover Tube Retainer Screws

    1. 1Fault

      • The engine fuel rail crossover tube retainer screws were not made to specification and may break; if one breaks, fuel could leak from the crossover joint, the engine may stall, and with an ignition source an engine compartment fire could occur.

    2. 2Finding the cause

      Possible causes

      • The failed screw was harder than specification; the over-hardening came from a conveyor in an induction hardening operation at the fastener plant stopping or slowing excessively, exposing the screws to the hardening for too long.

      Steps to confirm (in the document’s order)

      • Inspect for blue or green paint dots on the fuel rail crossover tube assembly or on the throttle body; if there are any, go to step 13.

    3. 3Correction

      Repair

      1. Hold the fuel crossover tube retainer to the bracket on the fuel rail with locking pliers, using enough force to keep the retainer from moving without damaging any parts.
      2. Remove the fuel rail crossover tube bracket retainer screw on one side and dispose of it properly.
      3. Take the new screws out of the retainer kit (P/N 89017590) and discard the retainer brackets left in the kit.
      4. Start the new screw by hand for at least 3 full turns into the fuel rail crossover tube retainer bracket.
      5. Torque the screw to 4.8Nm (42 lb in).

      Part numbers printed in the document

      The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

      3 more points

      Parts

      • Part number 89017590, RETAINER KIT, F/INJN FUEL RL C/OVR TUBE, quantity 1 per vehicle.

      Part numbers printed in the document

      The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

      Caution

      • Do not remove the crossover tube from the fuel rail or disturb the o-ring seal, because a fuel leak may result.
      • The service procedure in this recall differs from the one in the service manual.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：The recall covers certain 2005 Chevrolet Silverado, Tahoe and Suburban and GMC Sierra, Yukon and Yukon XL vehicles equipped with a 5.3L (RPO L59) E85 V8 engine and built within the listed VIN breakpoints.
    • Condition：The engine fuel rail crossover tube retainer screws were not made to specification and may break; if one breaks, fuel could leak from the crossover joint, the engine may stall, and with an ignition source an engine compartment fire could occur.
    • Cause：The failed screw was harder than specification; the over-hardening came from a conveyor in an induction hardening operation at the fastener plant stopping or slowing excessively, exposing the screws to the hardening for too long.
    • Confirm：Inspect for blue or green paint dots on the fuel rail crossover tube assembly or on the throttle body; if there are any, go to step 13.
    • Caution：Do not remove the crossover tube from the fuel rail or disturb the o-ring seal, because a fuel leak may result.
    • Caution：The service procedure in this recall differs from the one in the service manual.
    • Repair：Hold the fuel crossover tube retainer to the bracket on the fuel rail with locking pliers, using enough force to keep the retainer from moving without damaging any parts.
    • Repair：Remove the fuel rail crossover tube bracket retainer screw on one side and dispose of it properly.
    • Parts：Part number 89017590, RETAINER KIT, F/INJN FUEL RL C/OVR TUBE, quantity 1 per vehicle.
    • Repair：Take the new screws out of the retainer kit (P/N 89017590) and discard the retainer brackets left in the kit.
    • Repair：Start the new screw by hand for at least 3 full turns into the fuel rail crossover tube retainer bracket.
    • Repair：Torque the screw to 4.8Nm (42 lb in).
    • Repair：Check that the retainer is seated and not loose by trying to wiggle it slightly; it should not move. Then re-torque the screw to 4.8Nm (42 lb in).
    • Repair：Repeat steps 5 through 10 on the other side of the crossover tube.
    • Repair：Check for leaks: ignition ON with the engine OFF for 2 seconds, ignition OFF for 10 seconds, ignition ON with the engine OFF, then visually inspect for fuel leaks.
    Cause
    ON CERTAIN SPORT UTILITY VEHICLES AND PICKUP TRUCKS EQUIPPED WITH 5.3L (RPO L59) V8 ENGINES, THE ENGINE FUEL RAIL CROSSOVER TUBE RETAINER SCREWS WERE NOT MANUFACTURED TO SPECIFICATIONS AND MAY BREAK.
    Remedy
    DEALERS WILL INSPECT THE FUEL RAIL CROSSOVER TUBE AND, IF NECESSARY, REPLACE THE RETAINER SCREWS. OWNERS WERE NOTIFIED BY TELEPHONE ON JULY 30, 2004, WITH A FOLLOWUP OWNER LETTER BEGAN AUGUST 5, 2004. OWNERS SHOULD CONTACT CHEVROLET AT 1-800-630-2438 OR GMC AT 1-866-996-9463. NOTE: THE GM BULLETIN LISTS THE TAHOE AND YUKON MODELS BECAUSE CANADIAN VEHICLES ARE INCLUDED IN THE BULLETIN. NO U.S. TAHOE OR YUKON VEHICLES ARE INCLUDED IN THE U.S. CAMPAIGN.
    Consequence
    IF THE TUBE RETAINER SCREW BREAKS, FUEL COULD LEAK FROM THE FUEL RAIL CROSSOVER JOINT, THE ENGINE MAY STALL AND, IF AN IGNITION SOURCE WERE PRESENT, AN ENGINE COMPARTMENT FIRE COULD OCCUR.

  2. Recall2005 GMC YUKON XL ・ 2004-08-05

    Fuel Rail Crossover Tube Retainer Screws Recall

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      Not stated

      What the documents say to do

      Engine fuel rail crossover tube retainer screws may break (5.3L RPO L59) - recall 04V-376

      Confirm

      • Check for leaks: ignition ON with the engine OFF for 2 seconds, ignition OFF for 10 seconds, ignition ON with the engine OFF, then visually inspect for fuel leaks.

      Repair

      1. Dealers inspect the fuel rail crossover tube and replace the retainer screws if necessary.
      2. Hold the fuel crossover tube retainer to the bracket on the fuel rail with locking pliers, using enough force to keep the retainer from moving without damaging any parts.

      Caution

      • The GM bulletin lists Tahoe and Yukon models because Canadian vehicles are included in the bulletin.
    Read the sentences of the record
    Cause
    On certain vehicles, the fuel rail crossover tube retainer screws were not manufactured to specifications and may break. If a tube retainer screw breaks, fuel could leak from the fuel rail crossover joint, the engine may stall and, if an ignition source were present, an engine compartment fire could occur. Correction: Dealers will inspect the fuel rail crossover tube assembly and, if necessary, replace the two tube retainer screws.

Known issuesOut of fuel with the gauge reading above empty, cranks but no start, stall (replace the fuel sensor, not the sender module)1

  1. Manufacturer communication2001–2005 GMC FULL SIZE PICKUPS AND UTILITIES (YUKON XL) ・ 2005-12-01

    Cranks but no start, stall, or inaccurate fuel gauge with the tank out of fuel: replace the fuel sensor

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      Repair

      • Replace the fuel sensor.

      Caution

      • Do not replace the fuel sender module; the reference is bulletin 04-08-49-018E.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Row for 2001-2005 Full Size Pickups and Utilities: cranks but no start, stall, inaccurate/incorrect fuel gauge reading, no fuel, vehicle is out of fuel and the fuel gauge reads above empty.
    • Repair：Replace the fuel sensor.
    • Caution：Do not replace the fuel sender module; the reference is bulletin 04-08-49-018E.

    Open this issue of GM TechLink ↗ The points above are read from an article of TechLink, GM’s monthly publication for dealership technicians. The article itself is not reproduced here.

    Remedy
    Truck Issues — Fix It Right the First Time (new issues in bold) 2001-2005 Full Size Pickups and Utilities – Cranks But No Start, Stall, Inaccurate/Incorrect Fuel Gauge Reading, No Fuel, Vehicle is Out of Fuel and Fuel Gauge Reads Above Empty Replace fuel sensor. Don’t replace fuel sender module. 04-08-49-018E

Known issuesFuel module reservoir assembly: fuel pump wire connectors may overheat - recall 05V-1551

  1. Recall2000–2001 GMC YUKON XL ・ —

    Fuel Module Reservoir Assembly Overheating Recall

    1. 1Fault

      • Some vehicles were built with fuel module reservoir assemblies whose fuel pump wires and/or connectors may overheat under certain operating conditions.
      • If the exposed ignition circuit wire shorts to ground, the fuel pump fuse blows, disabling the fuel pump and causing an engine stall or no-start; if the ignition circuit or ground wire shorts to the fuel level sender card wires, fuel level readings may be inaccurate.
      • If enough heat reaches the pass-through connector, a hole may form in it, which may turn on the Service Engine Soon light during the emission system diagnostics routine; fuel vapor, and in some cases liquid fuel, may leak from the tank through the hole.
      • If enough fuel leaked out and an ignition source were present, a vehicle fire could occur.

    2. 2Finding the cause

      Possible causes

      • Fretting corrosion caused by vibration inside the tank was identified as the cause of high resistance within the fuel pump connector.

    3. 3Correction

      Repair

      1. Dealers remove the fuel tank, remove the fuel module reservoir assembly and install a new service kit, which includes a new pass-through connector and a wiring harness for the fuel pump and fuel sender card.
      2. Start by disconnecting the negative battery cable, then remove and discard the "ECM B" fuse.
      3. In the revised bulletin, the fuel and EVAP pipes are capped with J 41413-300, EVAP Cap/Plug Kit, to prevent fuel system contamination.
      4. Remove the 4 pin Metri Pack 150 electrical connector from the vehicle's body harness.
      5. Connect the new GT280 connector to the vehicle's body harness with the 4 butt splice connectors contained in the kit.
      2 more points

      Parts

      • Part number 15824379, Harness Kit, F/Tnk F/Pmp Mdl Wrg, quantity 1 per vehicle.

      Part numbers printed in the document

      The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

      Caution

      • Do not handle the fuel sender assembly by the fuel pipes; the leverage could damage the joints.
      • Always replace the fuel sender gasket when reinstalling the fuel sender assembly, to reduce the risk of fire and injury from a fuel leak.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：The recall covers certain 2000-2001 Chevrolet 1500 Series Suburban and GMC 1500 Series Yukon XL vehicles built within the listed VIN breakpoints.
    • Condition：Some vehicles were built with fuel module reservoir assemblies whose fuel pump wires and/or connectors may overheat under certain operating conditions.
    • Condition：If the exposed ignition circuit wire shorts to ground, the fuel pump fuse blows, disabling the fuel pump and causing an engine stall or no-start; if the ignition circuit or ground wire shorts to the fuel level sender card wires, fuel level readings may be inaccurate.
    • Condition：If enough heat reaches the pass-through connector, a hole may form in it, which may turn on the Service Engine Soon light during the emission system diagnostics routine; fuel vapor, and in some cases liquid fuel, may leak from the tank through the hole.
    • Condition：If enough fuel leaked out and an ignition source were present, a vehicle fire could occur.
    • Cause：Fretting corrosion caused by vibration inside the tank was identified as the cause of high resistance within the fuel pump connector.
    • Repair：Dealers remove the fuel tank, remove the fuel module reservoir assembly and install a new service kit, which includes a new pass-through connector and a wiring harness for the fuel pump and fuel sender card.
    • Parts：Part number 15824379, Harness Kit, F/Tnk F/Pmp Mdl Wrg, quantity 1 per vehicle.
    • Repair：Start by disconnecting the negative battery cable, then remove and discard the "ECM B" fuse.
    • Repair：In the revised bulletin, the fuel and EVAP pipes are capped with J 41413-300, EVAP Cap/Plug Kit, to prevent fuel system contamination.
    • Caution：Do not handle the fuel sender assembly by the fuel pipes; the leverage could damage the joints.
    • Caution：Always replace the fuel sender gasket when reinstalling the fuel sender assembly, to reduce the risk of fire and injury from a fuel leak.
    • Repair：Remove the 4 pin Metri Pack 150 electrical connector from the vehicle's body harness.
    • Repair：Connect the new GT280 connector to the vehicle's body harness with the 4 butt splice connectors contained in the kit.
    • Repair：Install the fuel tank strap attaching bolts and tighten them to 40 N·m (30 lb ft).
    • Repair：Install the new fuel pump fuse contained in the kit into the vehicle's electrical center (ECM B).
    Cause
    CERTAIN TRUCKS AND SPORT UTILITY VEHICLES WERE BUILT WITH FUEL MODULE RESERVOIR ASSEMBLIES THAT CONTAIN FUEL PUMP WIRES CONNECTORS MAY OVERHEAT UNDER CERTAIN OPERATING CONDITIONS.
    Remedy
    DEALERS WILL REMOVE THE FUEL TANK, AND REMOVE THE MODULE RESERVOIR ASSEMBLIES FROM THE TANK, AND INSTALL A NEW SERVICE KIT FREE OF CHARGE. AN INTERIM LETTER TO OWNERS WAS MAILED ON MAY 25, 2005. THE OWNERS WERE RE-NOTIFIED ON OCTOBER 19, 2005, SINCE PARTS ARE NOW AVAILABE. OWNERS MAY CONTACT CHEVROLET AT 1-800-630-2438 AND GMC AT 1-866-996-9463.
    Consequence
    IF THE IGNITION CIRCUIT WIRE IS EXPOSED, THE FUEL PUMP FUSE WILL BLOW, DISABLING THE FUEL PUMP AND CAUSING AN ENGINE STALL OR NO-START CONDITION. IF SUFFICIENT HEAT IS CONDUCTED TO THE PASS-THROUGH CONNECTOR, A HOLE IN THE CONNECTOR MAY RESULT, WHICH MAY CAUSE A 'SERVICE ENGINE SOON' LIGHT TO BE ILLUMINATED DURING THE EMISSION SYSTEM DIAGNOSTIC ROUTINE. FUEL VAPOR AND IN SOME CASES LIQUID FUEL MAY LEAK OUT OF THE FUEL TANK THROUGH THE HOLE IN THE CONNECTOR BODY. FUEL LEAKAGE, IN THE PRESENCE OF AN IGNITION SOURCE, COULD RESULT IN A FIRE. ALSO IF THE IGNITION CIRCUIT OR GROUND WIRE IS EXPOSED AND SHORTS TO THE FUEL LEVEL SENDER CARD WIRES, INACCURATE FUEL LEVEL READINGS MAY RESULT.

Known issuesReduced Engine Power from throttle body connector crimp, broken wire or grounds1

  1. Owner complaint2003 GMC YUKON XL 2500 ・ 2010-03-10

    Service engine light and reduced power mode episodes since November 2008

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

    Read the sentences of the record
    Fault
    SINCE NOVEMBER 2008, MY 2003 GMC YUKON XL 2500 HAS HAD EPISODES WHERE THE SERVICE ENGINE LIGHT COMES ON AND THE ENGINE GOES INTO REDUCED POWER MODE.
    Remedy
    I HAVE TAKEN IT TO NUMEROUS GM DEALERS TO FIX THE PROBLEM, AND THEY HAVE REPLACED THE THROTTLE BODY ASSEMBLE AND WIRING HARNESS MULTIPLE TIMES AND THE PROBLEM KEEPS RECURRING.
    Consequence
    THERE HAVE BEEN MANY CLOSE EPISODES WHERE WE WERE ALMOST IN AN ACCIDENT.

ENGINE AND ENGINE COOLING6

  1. Owner complaint2002 GMC YUKON XL DENALI ・ 2008-03-27

    Vehicle stalled while driving at 65 MPH; braking and power steering lost

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

    Read the sentences of the record
    Fault
    WHILE DRIVING ABOUT 65 MPH (= 104.6 km/h) UNDER NORMAL DRY CONDITIONS THE VEHICLE STALLED. (1 more)
    Remedy
    THE VEHICLE HAD BEEN TAKEN TO THE DEALER WHERE THEY FIXED THE THROTTLE BODY AND WATER PUMP.
    Consequence
    THE CONTACT WAS ABLE TO GET THE VEHICLE TO THE SIDE OF THE ROAD WITHOUT A CRASH.

  2. Owner complaint2002 GMC YUKON XL 1500 ・ 2010-07-21

    Engine stalls while driving in traffic

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      Not stated

    Read the sentences of the record
    Fault
    THIS VEHICLE THAT I RECENTLY PURCHASED HAS STALLED ON TWO OCCASIONS WHILE DRIVING.
    Consequence
    BOTH TIMES I WAS IN TRAFFIC AND HAD DIFFICULTY SAFELY GETTING OFF THE ROADWAY, AS I HAD NO POWER.

  3. Owner complaint2002 GMC YUKON XL ・ 2008-01-10

    2002 GMC Yukon XL would not start and stalled intermittently while driving

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

    Read the sentences of the record
    Fault
    THE CONTACT STATED THAT THE VEHICLE WOULD NOT START. (4 more)
    Remedy
    *LJ THE CONSUMER STATED THE CRANKSHAFT POSITION SENSOR WAS REPLACED.

  4. Owner complaint2002 GMC YUKON XL ・ 2007-11-05

    GMC Yukon 2500 8.1L stalls while driving

    1. 1Fault

    2. 2Finding the cause

      I BELIEVE IT IS THE CAM POSITIONING SENSOR.

    3. 3Correction

      Not stated

    Read the sentences of the record
    Fault
    MY GMC YUKON 2500 WITH THE 8.1L STALLS WHILE DRIVING.
    Cause
    I BELIEVE IT IS THE CAM POSITIONING SENSOR.

  5. Owner complaint2002 GMC YUKON XL ・ 2007-04-04

    Car stalls while traveling down highway, occurs at least once on each trip

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      Not stated

    Read the sentences of the record
    Fault
    CAR STALLS WHILE TRAVELING DOWN HIGHWAY, OCCURS AT LEAST ONCE ON EACH TRIP. (1 more)
    Consequence
    WE HAVE HAD SEVERAL NEAR REAR END CRASHES AND SCARY MOMENTS WHEN ON THE INSIDE LANE OF AN INTERSTATE PULLING A 16 FT (= 4.88 m) TRAILER. *JB

  6. Manufacturer communication2002–2004 GMC YUKON XL ・ 2004-08-13

    Flexible Fuel Vehicle Starting, Stalling, Power Loss and Performance Issues

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      VEHICLE WITH FLEXIBLE FUEL WILL NOT START, STALLS AND WILL NOT RESTART, LOSS OF POWER, POOR PERFORMANCE. *TT POOR PERFORMANCE AND/OR FUEL GAUGE READS INACCURATE/INCORRECT. *TT

    Read the sentences of the record
    Remedy
    VEHICLE WITH FLEXIBLE FUEL WILL NOT START, STALLS AND WILL NOT RESTART, LOSS OF POWER, POOR PERFORMANCE. *TT POOR PERFORMANCE AND/OR FUEL GAUGE READS INACCURATE/INCORRECT. *TT

FUEL SYSTEM, GASOLINE6

  1. Owner complaint2001 GMC YUKON XL ・ 2006-01-27

    Vehicle sputters and stalls at intersections

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      THE VEHICLE WAS TAKEN TO A SERVICE DEALER WHO REPLACED THE PART.

    Read the sentences of the record
    Fault
    THE VEHICLE SPUTTERS AND STALLS AT INTERSECTIONS.
    Remedy
    THE VEHICLE WAS TAKEN TO A SERVICE DEALER WHO REPLACED THE PART.
    Outcome
    THE PROBLEMS CONTINUED TO HAPPEN EVEN AFTER THE PART WAS REPLACED.

  2. Manufacturer communication2000–2006 GMC YUKON XL ・ 2018-05-21(1 earlier editions of this document folded here)

    E85 Fuel Effects on Non-E85 Vehicles Information

    1. 1Fault

      • Using this fuel in a non-compatible vehicle may cause lean driveability concerns such as hesitation, sag and/or possible stalling.
      • Fuel trim DTC P0171 and/or P0174 may set.
      • Misfire DTC P0300 may set.
      • A Traction Control, Stability System or ABS lamp may illuminate, or a message may display in the DIC (if equipped).
      • Harsh and/or firm transmission shifts may occur because the transmission defaults to maximum line pressure.

    2. 2Finding the cause

      Steps to confirm (in the document’s order)

      1. Alcohol content is checked using Special Tool J-44175-A Fuel Composition Tester or CH-44175-A Fuel Composition Tester.
      2. General Motors started putting yellow gas caps on E85 Flex Fuel Vehicles (FFVs) as of Model Year 2006.

    3. 3Correction

      Repair

      • If the ethanol content exceeds the Owner Manual maximum of 10% or 15%, drain the fuel and refill the vehicle with gasoline, preferably a Top Tier brand.

      Caution

      • All Model Year 2011 and older non-FFV gasoline vehicles are designed to run on fuel containing no more than 10% ethanol.
      • Diesel engines are not E85 compatible.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：The list of compatible flexible-fuel vehicles includes 2002–2005 fullsize pickups and utilities with 5.3L, RPO L59.
    • Applies to：The list of compatible flexible-fuel vehicles includes 2006 Sierra, Yukon and Yukon XL with 5.3L, RPO L59.
    • Caution：All Model Year 2011 and older non-FFV gasoline vehicles are designed to run on fuel containing no more than 10% ethanol.
    • Caution：Diesel engines are not E85 compatible.
    • Condition：Using this fuel in a non-compatible vehicle may cause lean driveability concerns such as hesitation, sag and/or possible stalling.
    • Condition：Fuel trim DTC P0171 and/or P0174 may set.
    • Condition：Misfire DTC P0300 may set.
    • Condition：A Traction Control, Stability System or ABS lamp may illuminate, or a message may display in the DIC (if equipped).
    • Condition：Harsh and/or firm transmission shifts may occur because the transmission defaults to maximum line pressure.
    • Confirm：Alcohol content is checked using Special Tool J-44175-A Fuel Composition Tester or CH-44175-A Fuel Composition Tester.
    • Repair：If the ethanol content exceeds the Owner Manual maximum of 10% or 15%, drain the fuel and refill the vehicle with gasoline, preferably a Top Tier brand.
    • Confirm：General Motors started putting yellow gas caps on E85 Flex Fuel Vehicles (FFVs) as of Model Year 2006.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This informational bulletin provides the technician with information on what E85 fuel may due to a non E85 vehicle.

  3. Owner complaint2001 GMC YUKON XL 2500 ・ 2006-09-21

    Vehicle stalled while driving; fuel pump fuse failure and wiring issue

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

    Read the sentences of the record
    Fault
    DT*: THE CONTACT STATED WHILE DRIVING 70 MPH (= 112.7 km/h) ON NORMAL ROAD CONDITIONS, THE VEHICLE STALLED. (1 more)
    Remedy
    THE FUSE WAS REPLACED.
    Inspection
    THE VEHICLE WAS TOWED TO A DEALER WHO DETERMINED THE FUSE OF THE FUEL PUMP HAD GONE OUT. (1 more)

  4. Owner complaint2002 GMC YUKON XL ・ 2006-05-17

    Fuel pump failure with blown ECMB fuse; vehicle stalls after fuse replacement

    1. 1Fault

    2. 2Finding the cause

    3. 3CorrectionNot repaired

    Read the sentences of the record
    Remedy
    TRUCK IS STILL NOT FIXED. JB
    Inspection
    FUEL PRESSURE WAS FOUND AT 24 PSI (= 165.5 kPa). (1 more)

  5. Owner complaint2004 GMC YUKON XL ・ 2005-09-06

    Vehicle stalls while driving on freeway during hot weather and on inclines

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

    Read the sentences of the record
    Fault
    OUR 2004 GMC YUKON CONTINUES TO STALL WHILE DRIVING ON FREEWAY DURING HOT WEATHER AND ON INCLINES.
    Remedy
    FUEL PUMP WAS REPLACED ON 6/29/05, 7/29/05, AND ON 9/6/05.

  6. Owner complaint2000 GMC YUKON XL ・ 2003-03-28

    Vehicle stalled

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      Not stated

    Read the sentences of the record
    Fault
    THE VEHICLE STALLED.
    Cause
    THE WIRES SHORTED WHICH CAUSED VEHICLE TO STALL. *JB
    Inspection
    THE DEALER DIAGNOSED THE PROBLEM AS BAD BARE WIRES INSIDE OF FUEL PUMP.

ELECTRICAL SYSTEM4

  1. Owner complaint2003 GMC YUKON XL ・ 2010-02-16

    Vehicle stalls while in motion and when braking

    1. 1Fault

    2. 2Finding the cause

      FIGURED OUT IT MAY BE RUNNING OUT OF GAS DUE TO THE GAUGE NOT WORKING.

    3. 3Correction

    Read the sentences of the record
    Fault
    VEHICLE STALLS WHILE IN MOTION. (1 more)
    Cause
    FIGURED OUT IT MAY BE RUNNING OUT OF GAS DUE TO THE GAUGE NOT WORKING.
    Remedy
    REPLACED THE FUEL FILTER TWICE. (1 more)

  2. Owner complaint2003 GMC YUKON XL 1500 ・ 2017-12-12

    Vehicle randomly enters reduce engine power mode and stalls while driving

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      Not stated

    Read the sentences of the record
    Fault
    VEHICLE RANDOMLY GOES INTO REDUCE ENGINE POWER MODE AND STALLS WHILE DRIVING.
    Cause
    THERE IS A PROBLEM WITH BAD GROUNDING CONNECTORS RELATED TO THE THROTTLE BODY SENSOR AND AND WIRING HARNESS.

  3. Owner complaint2003 GMC YUKON DENALI XL ・ 2013-09-11

    Reduce Engine Power warning, engine stall and loss of speed while driving

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      Not stated

    Read the sentences of the record
    Fault
    DRIVING TO WORK AND "REDUCE ENGINE POWER" CAME ON. (1 more)
    Consequence
    I WAS IN A LOT OF TRAFFIC WHEN THIS HAPPEN AND MY VEHICLE CAUSE A INCIDENT BECAUSE OF THE SUDDEN ENGINE REDUCED ALL SPEED.

  4. Owner complaint2003 GMC YUKON XL ・ 2006-06-06

    Loud grinding noise and bang at highway speeds, stall with white smoke, recurring

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

    Read the sentences of the record
    Fault
    DT*: THE CONTACT STATED ON THREE OCCASIONS WHILE DRIVING AT HIGHWAY AND FREEWAY SPEEDS OF 30- 75 MPH (= 48.3–120.7 km/h) THE VEHICLE MADE A LOUD GRINDING NOISE FOLLOWED BY ANOTHER LOUD BANG. (1 more)
    Remedy
    THE ENTIRE A/C WAS REPLACED ON TWO OCCASIONS. (2 more)

ELECTRONIC STABILITY CONTROL (ESC)3

  1. Owner complaint2004 GMC YUKON XL 1500 ・ 2016-01-06

    Engine stall and loss of power while driving at 60 MPH

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3CorrectionNot repaired

      THE VEHICLE WAS NOT REPAIRED.

    Read the sentences of the record
    Fault
    THE ENGINE STALLED AND LOST POWER. (1 more)
    Remedy
    THE VEHICLE WAS NOT REPAIRED.
    Inspection
    THE VEHICLE WAS TAKEN TO A LOCAL DEALER WHO WAS UNABLE TO DUPLICATE AND DIAGNOSE THE FAILURE.

  2. Owner complaint2003 GMC YUKON DENALI XL ・ 2011-12-30

    Traction control and ABS engaging at low speeds, causing loss of power and accidents

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      Not stated

    Read the sentences of the record
    Fault
    WHEN THE TRACTION CONTROL ENGAGES, A TOTAL LOSS OF INPUT TO THE ENGINE RESULTS AND THE VEHICLE DOES NOT MOVE (IT ESSENTIALLY STALLS). (4 more)
    Inspection
    WHAT IS EVEN MORE FRUSTRATING IS THAT THE DEALERSHIP COULD NOT PROPERLY DIAGNOSE THE PROBLEM FOR SEVERAL YEARS BECAUSE THEY COULD NOT "REPLICATE THE PROBLEM ."
    Consequence
    I WAS ALMOST STRUCK IN AN INTERSECTION WHILE WAITING TO MAKE A LEFT TURN ON A GREEN LIGHT IN EARLY DECEMBER OF 2011. (1 more)

  3. Owner complaint2005 GMC YUKON XL 1500 ・ 2011-12-13

    Traction control and ABS malfunction during acceleration and braking

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      Not stated

    Read the sentences of the record
    Cause
    IN ALL CASES, ACTIVATION IS IN ERROR BASED ON AMBIENT CONDITIONS. (1 more)
    Inspection
    MY MECHANIC ADVISED ME THAT IT REQUIRES CHANGING THE FULL FRONT WHEEL BEARING ASSEMBLY BECAUSE OF CORROSION BUILDUP ON THE TONE RING.

ENGINE3

  1. Owner complaint2001 GMC YUKON XL 2500 ・ 2015-12-24

    Engine stalled at highway speeds without power steering or brakes

    1. 1Fault

    2. 2Finding the cause

      AFTER LOOKING AT AN ON-LINE FORUM, THE VEHICLE WITH THE 8.1 LITER ENGIN HAD SOME VEHICLES RECALLED WITH A CAM LOBE SENSOR FAULT WHICH CAUSES THIS TO HAPPEN. (1 more)

    3. 3Correction

      HOWEVER, WHEN THE VEHICLE WAS NEW, THEY HAD ALREADY REPLACE THE SAME PART WHEN THE VEHICLE WAS 3-5 MONTHS OLD.

    Read the sentences of the record
    Fault
    WHILE TRAVELING AT HIGHWAY SPEEDS THE ENGINE STOPPED WORKING / STALLED.
    Cause
    AFTER LOOKING AT AN ON-LINE FORUM, THE VEHICLE WITH THE 8.1 LITER ENGIN HAD SOME VEHICLES RECALLED WITH A CAM LOBE SENSOR FAULT WHICH CAUSES THIS TO HAPPEN. (1 more)
    Remedy
    HOWEVER, WHEN THE VEHICLE WAS NEW, THEY HAD ALREADY REPLACE THE SAME PART WHEN THE VEHICLE WAS 3-5 MONTHS OLD.

  2. Owner complaint2004 GMC YUKON DENALI XL ・ 2015-09-23

    Engine stalls while driving at approximately 60 MPH

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

    Read the sentences of the record
    Fault
    WHILE DRIVING APPROXIMATELY 60 MPH (= 96.6 km/h), THE VEHICLE STALLED. (1 more)
    Remedy
    THE MECHANIC REPLACED THE TAC MODULE AND ELECTRONIC THROTTLE BODY, BUT THE FAILURE RECURRED. (1 more)

  3. Owner complaint2000 GMC YUKON XL ・ 2017-12-20

    Vehicle stalls while driving at 55 MPH with sputtering noise

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3CorrectionNot repaired

      THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED.

    Read the sentences of the record
    Fault
    WHILE DRIVING 55 MPH (= 88.5 km/h), THE VEHICLE MADE A SPUTTERING NOISE AND STALLED. (1 more)
    Remedy
    THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED.

EQUIPMENT2

  1. Manufacturer communication2000–2006 GMC YUKON XL DENALI ・ 2022-04-05

    Fuel Injector Maintenance Cleaning Service Bulletin

    1. 1Fault

      • Use the detergent fuel additives when the vehicle shows loss of power, diminished performance, frequent stalls or no starts, or a noted decrease in fuel economy.

    2. 2Finding the cause

      Not stated

    3. 3Correction

      Repair

      1. The only preventative maintenance GM endorses for gasoline engine fuel systems is GM Fuel System Treatment PLUS added to a tank of fuel at each oil change.
      2. Regular use of a TOP TIER Detergent Gasoline helps prevent the build-up of intake valve and fuel injector deposits.

      Parts

      • Part number 88865595 (88865598 for Canada): CLEANER, FUEL SYSTEM TREATMENT 12 OZ. (GASOLINE).
      • Part number 88865596 (88865599 for Canada): CLEANER, FUEL SYSTEM TREATMENT 12 OZ. (FLEX FUEL).

      Part numbers printed in the document

      The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

      Caution

      • GM does not endorse, support or acknowledge the need for fuel injector cleaning as a preventative maintenance procedure.
      • Fuel injector cleaning is approved only when a published GM driveability or DTC diagnostic service procedure directs it.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to 2022 and earlier GM passenger cars and trucks.
    • Caution：GM does not endorse, support or acknowledge the need for fuel injector cleaning as a preventative maintenance procedure.
    • Caution：Fuel injector cleaning is approved only when a published GM driveability or DTC diagnostic service procedure directs it.
    • Repair：The only preventative maintenance GM endorses for gasoline engine fuel systems is GM Fuel System Treatment PLUS added to a tank of fuel at each oil change.
    • Repair：Regular use of a TOP TIER Detergent Gasoline helps prevent the build-up of intake valve and fuel injector deposits.
    • Condition：Use the detergent fuel additives when the vehicle shows loss of power, diminished performance, frequent stalls or no starts, or a noted decrease in fuel economy.
    • Parts：Part number 88865595 (88865598 for Canada): CLEANER, FUEL SYSTEM TREATMENT 12 OZ. (GASOLINE).
    • Parts：Part number 88865596 (88865599 for Canada): CLEANER, FUEL SYSTEM TREATMENT 12 OZ. (FLEX FUEL).

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.

  2. Manufacturer communication2000–2006 GMC YUKON XL ・ 2021-04-19(1 earlier editions of this document folded here)

    Winter Fuel Grade Use in Warm Months 2020 – Drivability Issues

    1. 1Fault

      • In rare instances customers may complain of a fuel smell, longer starts, hesitation and, in extreme cases, engine stalls.
      • Any combination of DTCs P0300, P0171, P0174 and P228C may be set.

    2. 2Finding the cause

      Possible causes

      • Using winter fuel in summer weather may cause drivability concerns.

      Steps to confirm (in the document’s order)

      • The concern should not be a single event but multiple occurrences associated with hot days.

    3. 3Correction

      Caution

      • No repair is required; the vehicles are not damaged and will recover.
      • There is no other remedy until summer fuel and/or cooler weather is available.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to all brands and models with gasoline engines, model years 2000 - 2022.
    • Applies to：The involved region is North America.
    • Condition：In rare instances customers may complain of a fuel smell, longer starts, hesitation and, in extreme cases, engine stalls.
    • Condition：Any combination of DTCs P0300, P0171, P0174 and P228C may be set.
    • Cause：Using winter fuel in summer weather may cause drivability concerns.
    • Confirm：The concern should not be a single event but multiple occurrences associated with hot days.
    • Caution：No repair is required; the vehicles are not damaged and will recover.
    • Caution：There is no other remedy until summer fuel and/or cooler weather is available.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use.  Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement.  This will extend the use of winter fuel into the summer months. The drivability concerns should not be single events but should be multiple occurrences associated with hot days.

No component category1

  1. Manufacturer communication2000–2001 GMC C/K PICKUP AND UTILITY MODELS (YUKON XL) ・ 2001-08-01

    Security lamp on, stall or no start, DTC B2960 (revision A) (bulletin 01-08-56-002A)

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      Repair

      • The condition is the Security lamp illuminated on the instrument panel, engine stalls or no start, with DTC B2960 (Security System Sensor Data Incorrect but Valid) set; the correction is to inspect and repair the cause of DTC B2960.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Bulletin 01-08-56-002A replaces 01-08-56-002 and applies to 1999-2001 Chevrolet and GMC C/K Pickup and Utility Models with DTC B2960 set.
    • Repair：The condition is the Security lamp illuminated on the instrument panel, engine stalls or no start, with DTC B2960 (Security System Sensor Data Incorrect but Valid) set; the correction is to inspect and repair the cause of DTC B2960.

    Open this issue of GM TechLink ↗ The points above are read from an article of TechLink, GM’s monthly publication for dealership technicians. The article itself is not reproduced here.

    Remedy
    This review of service bulletins released through mid-July 01-08-56-002A; replaces 01-08-56- 002; Security Lamp Illuminated on the IP, Engine Stalls, No Start, DTC B2960 (Security System Sensor Data Incorrect but Valid) Set (Inspect and Repair Cause of DTC B2960); 1999-2001 Chevrolet and GMC C/K Pickup and Utility Models Security Lamp Illuminated on the IP, Engine Stalls, No Start, DTC B2960 (Security System Sensor Data Incorrect but Valid) Set (Inspect and Repair Cause of DTC B2960)

ELECTRICAL1

  1. Recall2000–2001 GMC YUKON XL ・ 2005-04-15

    Fuel Module Reservoir Assembly Overheating Recall

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      Not stated

    Read the sentences of the record
    Cause
    Certain vehicles were built with fuel module reservoir assemblies that contain fuel pump wires and/or connectors that may overheat under certain operating conditions. Fuel pump wires that overheat may become exposed and result in one or more conditions; 1) If the ignition circuit wire is exposed and shorts to ground, the fuel pump fuse will blow, disabling the fuel pump and causing an engine stall or no-start condition. 2) If sufficient heat is conducted to the pass-through connector, a hole in the connector may result, which may cause the Service Engine Soon light to be illuminated during the emission system diagnostics routine. Fuel vapour (and in some limited cases liquid fuel) may leak out of the fuel tank through the hole in the connector body. 3) If the ignition circuit or ground wire is exposed and shorts to the fuel level sender card wires, inaccurate fuel level readings may result. Correction: Dealers will affect repairs.

Showing 34 of the 54 you can open. Narrow the search to see the rest.

4 owner complaints have no classified sentences yet, so their causes and repairs are not picked out. Their text is in the list of records.