Skip to content
FaultCrate
日本語Open preview: everything readable

This is an open preview: every record can be read without an account. The details of the plans are in preparation.

GMC Yukon XL 2000–2006

GMC Yukon XLModel years 2000–2006

Change vehicle →
Clear the search
2 conditions added

Common on this vehicle:Warning lightLeakNoiseStalls or shuts offSmoke or fireVibration or shudderCorrosion or rustGauge or instrument fault

Record by record

12 records state a cause or a remedy. Each record is shown as short labels in the order fault → finding the cause → correction. Press a label to narrow to the records that state it.

Symptom

Component named as the cause

Work done

How it is said to have ended

  • says it was fixed1
  • result not stated2

A ribbon is as wide as the records that state both of its ends (only the commonest are drawn). A record that names several symptoms or components runs through each. Orange is records that say the fault came back or was not fixed. Results come from owners’ reports only; one that does not say is “result not stated”. None of this is a likelihood of a cause or a rate at which work succeeds.

Read the records one by one (10)

Known issuesFuel gauge reads low or drops to empty in Park / Neutral (normal characteristic)1

  1. Manufacturer communication2000–2006 GMC YUKON XL ・ 2017-08-15

    Fuel Gauge Accuracy—Preliminary Information

    1. 1Fault

      • The fuel gauge may be inaccurate or drop to empty (E) with the low fuel light coming on.
      • The condition is most apparent when the gauge is at or below the quarter (1/4) tank mark.

    2. 2Finding the cause

      Possible causes

      • On an automatic transmission no buffering of the fuel gauge takes place when the transmission is in park or neutral.

      Steps to confirm (in the document’s order)

      1. Try to duplicate it by driving a short distance in reverse and stopping (to make fuel slosh), shifting to park or neutral and then to drive.
      2. Note how the vehicle is being parked (on an incline, front of the vehicle up hill or down hill).

    3. 3Correction

      Caution

      • This is a normal characteristic and no repairs are necessary.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：The model list names 2000-2015 GMC Yukon models.
    • Condition：The fuel gauge may be inaccurate or drop to empty (E) with the low fuel light coming on.
    • Condition：The condition is most apparent when the gauge is at or below the quarter (1/4) tank mark.
    • Confirm：Try to duplicate it by driving a short distance in reverse and stopping (to make fuel slosh), shifting to park or neutral and then to drive.
    • Confirm：Note how the vehicle is being parked (on an incline, front of the vehicle up hill or down hill).
    • Cause：On an automatic transmission no buffering of the fuel gauge takes place when the transmission is in park or neutral.
    • Caution：This is a normal characteristic and no repairs are necessary.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This Preliminary Information communication provides information to the technician about vehicles that have an inaccurate fuel gauge. Technician should drive the vehicle to duplicate the concern. The fuel gauge will have a tendency to falsely indicate a lower fuel level than what is actually present. The fuel gauge will take a few minutes to show the correct fuel level. On vehicles equipped with an automatic transmission no buffering takes place when the transmission is in park or neutral. This is a normal characteristic and no repairs are necessary. On vehicles equipped with a manual transmission the fuel gauge is buffered in all gears and neutral. There is a timer which starts to count up when the clutch is depressed. When this timer reaches its calibrated value the buffering stops. This is a normal characteristic and no repairs are necessary.

Known issuesFuel module reservoir assembly: fuel pump wire connectors may overheat - recall 05V-1551

  1. Owner complaint2000 GMC YUKON XL ・ 2006-07-24

    Inaccurate fuel gauge readings

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

    Read the sentences of the record
    Fault
    DT*: THE CONTACT STATED THE FUEL GAUGE READINGS WERE INACCURATE.
    Remedy
    THE DEALER REPLACED THE FUEL PUMP WHICH CORRECTED THE PROBLEM.

ELECTRICAL SYSTEM2

  1. Manufacturer communication2000–2006 GMC YUKON XL ・ 2017-12-14(1 earlier editions of this document folded here)

    Inaccurate Odometer Reading – Preliminary Information

    1. 1Fault

      • A customer may say the odometer appears inaccurate compared with a known distance traveled.

    2. 2Finding the cause

      Steps to confirm (in the document’s order)

      1. Use a hand-held GPS unit to test the odometer.
      2. On a straight road over a mile long, mark the GPS waypoint when the odometer (not the trip odometer) rolls over a digit.
      3. Confirm that the original size tires and wheels are mounted and that the axle ratio is as specified on the SPID label and unmodified.
      4. If those are correct and the odometer is beyond the limit, consider the relationship between the VSS and the reluctor on the transmission output shaft.
      5. Closely inspect the associated wiring and any connectors in the circuits.

    3. 3Correction

      Repair

      • Finally, it may be necessary to exchange the IPC with a replacement unit.

      Caution

      • Generally a tolerance of plus or minus 4% is allowed.
      • Do not compare with another vehicle or with the trip odometer.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to all brands and models, model years 2000 - 2018.
    • Condition：A customer may say the odometer appears inaccurate compared with a known distance traveled.
    • Caution：Generally a tolerance of plus or minus 4% is allowed.
    • Confirm：Use a hand-held GPS unit to test the odometer.
    • Confirm：On a straight road over a mile long, mark the GPS waypoint when the odometer (not the trip odometer) rolls over a digit.
    • Caution：Do not compare with another vehicle or with the trip odometer.
    • Confirm：Confirm that the original size tires and wheels are mounted and that the axle ratio is as specified on the SPID label and unmodified.
    • Confirm：If those are correct and the odometer is beyond the limit, consider the relationship between the VSS and the reluctor on the transmission output shaft.
    • Confirm：Closely inspect the associated wiring and any connectors in the circuits.
    • Repair：Finally, it may be necessary to exchange the IPC with a replacement unit.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.

  2. Manufacturer communication2000–2006 GMC YUKON XL ・ 2017-08-15

    Instrument Panel Cluster Mileage Programming Information

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      Repair

      • When the odometer cannot be set to the actual vehicle mileage, it must be set at zero and a label affixed to the driver's door frame by the service agent.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to 2014 and prior GM passenger cars and trucks.
    • Repair：When the odometer cannot be set to the actual vehicle mileage, it must be set at zero and a label affixed to the driver's door frame by the service agent.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This Preliminary Information communication provides information to the technician that after replacing the Instrument Panel Cluster the exchange center is unable to program the actual mileage on the odometer or the actual mileage is unknown. Dealer will need to follow dealer to the General Motors service policies and procedures manual section 3.2.4 odometer servicing.

FUEL SYSTEM, GASOLINE2

  1. Owner complaint2000 GMC YUKON XL 2500 ・ 2007-11-30

    Fuel leak at main fuel tank access port after complete filling

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

    Read the sentences of the record
    Fault
    FUEL LEAK AT THE MAIN FUEL TANK ACCESS PORT.
    Outcome
    NOW ON NOVEMBER 29, 2007 AFTER COMPLETELY FILLING THE LEAK IS BACK AGAIN, UP UNTIL THIS POINT THE REPAIR ALOUD COMPLETE FILLING. *TR

  2. Owner complaint2000 GMC YUKON XL ・ 2005-09-13

    Gas gauge completely quit working

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

    Read the sentences of the record
    Fault
    OUR GAS GAUGE ON OUR 2000 GMC YUKON COMPLETELY QUIT WORKING.
    Inspection
    TOOK IT IN THINKING IT WAS AN ELECTRICAL PROBLEM AND FOUND OUT THE FUEL PUMP WAS BROKEN.

No component category1

  1. Manufacturer communication2000–2001 GMC C/K UTILITY MODELS (YUKON XL) ・ 2001-08-01

    Diagnosing a fuel gauge that reads empty with a low fuel message and DTCs (bulletin 01-06-04-036)

    1. 1Fault

      • It covers diagnosing a fuel gauge reading empty, a low fuel message displayed and DTCs set.

    2. 2Finding the cause

      Not stated

    3. 3Correction

      This review of service bulletins released through mid-July 01-06-04-036; Diagnosing Fuel Gauge Reading Empty, Low Fuel Message Displayed, DTCs Set; 2000-01 Chevrolet and GMC C/K Utility Models with Dual Fuel Tanks Diagnosing Fuel Gauge Reading Empty, Low Fuel Message Displayed, DTCs Set

    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Bulletin 01-06-04-036 applies to 2000-01 Chevrolet and GMC C/K Utility Models with dual fuel tanks.
    • Condition：It covers diagnosing a fuel gauge reading empty, a low fuel message displayed and DTCs set.

    Open this issue of GM TechLink ↗ The points above are read from an article of TechLink, GM’s monthly publication for dealership technicians. The article itself is not reproduced here.

    Remedy
    This review of service bulletins released through mid-July 01-06-04-036; Diagnosing Fuel Gauge Reading Empty, Low Fuel Message Displayed, DTCs Set; 2000-01 Chevrolet and GMC C/K Utility Models with Dual Fuel Tanks Diagnosing Fuel Gauge Reading Empty, Low Fuel Message Displayed, DTCs Set

ENGINE AND ENGINE COOLING1

  1. Manufacturer communication2000–2006 GMC YUKON XL ・ 2017-08-15(1 earlier editions of this document folded here)

    Engine Check Lamp P0442 Evaporative Emissions System Notification

    1. 1Fault

      • The service engine soon lamp (MIL) is on for DTC P0442, but a leak cannot be verified with the system test in the service information.

    2. 2Finding the cause

      Steps to confirm (in the document’s order)

      1. With the scan tool, command the EVAP system CLOSED, start the engine and watch the tank pressure sensor value for about two minutes.
      2. If the tank pressure value changes (shows vacuum), remove the purge solenoid and pressurize its fuel tank side with the GE 41413-A / J 41413-A tester.
      3. If the tank pressure value does not change, install the CH-48096 adaptor between the purge line from the canister and the purge solenoid; use no other adaptor or pressurization method.
      4. With the EVAP system CLOSED, pressurize through the adaptor and let the system stabilize, watching the gauge for at least 5 minutes, then add smoke.
      5. Look for smoke or UV trace fluid at the purge solenoid, the engine side, the fuel cap or capless fill door, and the canister vent solenoid filter or fresh-air line.
      1 more points

    3. 3Correction

      Repair

      • If smoke passes through the purge solenoid, replace the purge solenoid.

      Caution

      • After verifying P0442, do not disturb any fuel system component before testing.
      • Test pressure must not exceed 13 in H2O (0.5 PSI (= 3.45 kPa)); more can make components perform inaccurately and lead to misdiagnosis.
      • A large temperature difference between vehicle, shop and tester seriously affects accuracy; let the vehicle adjust to shop temperature first.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to 2016 and prior passenger cars and trucks.
    • Condition：The service engine soon lamp (MIL) is on for DTC P0442, but a leak cannot be verified with the system test in the service information.
    • Caution：After verifying P0442, do not disturb any fuel system component before testing.
    • Confirm：With the scan tool, command the EVAP system CLOSED, start the engine and watch the tank pressure sensor value for about two minutes.
    • Confirm：If the tank pressure value changes (shows vacuum), remove the purge solenoid and pressurize its fuel tank side with the GE 41413-A / J 41413-A tester.
    • Repair：If smoke passes through the purge solenoid, replace the purge solenoid.
    • Confirm：If the tank pressure value does not change, install the CH-48096 adaptor between the purge line from the canister and the purge solenoid; use no other adaptor or pressurization method.
    • Confirm：With the EVAP system CLOSED, pressurize through the adaptor and let the system stabilize, watching the gauge for at least 5 minutes, then add smoke.
    • Confirm：Look for smoke or UV trace fluid at the purge solenoid, the engine side, the fuel cap or capless fill door, and the canister vent solenoid filter or fresh-air line.
    • Confirm：If smoke testing finds nothing, the leak may exist only under vacuum: use the scan tool Purge/Seal function to pull a vacuum and watch the FTP sensor parameter for vacuum decay.
    • Caution：Test pressure must not exceed 13 in H2O (0.5 PSI (= 3.45 kPa)); more can make components perform inaccurately and lead to misdiagnosis.
    • Caution：A large temperature difference between vehicle, shop and tester seriously affects accuracy; let the vehicle adjust to shop temperature first.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.

FUEL SYSTEM, OTHER1

  1. Manufacturer communication2000–2006 GMC YUKON XL DENALI ・ 2004-09-27

    Fuel Gauge Fluctuation in Park or Neutral

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      FUEL GAUGE FLUCTUATION IN PARK OR NEUTRAL. *TT

    Read the sentences of the record
    Remedy
    FUEL GAUGE FLUCTUATION IN PARK OR NEUTRAL. *TT

POWER TRAIN1

  1. Manufacturer communication2000–2003 GMC YUKON XL ・ 2003-12-04

    Transmission Stuck in Third Gear or Inoperative Instrument Cluster

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      MALFUNCTION INDICATOR LAMP (MIL) IS ON; THE TRANSMISSION IS STUCK IN THIRD GEAR; AND / OR THE INSTRUMENT CLUSTER IS INOPERATIVE. *TT

    Read the sentences of the record
    Remedy
    MALFUNCTION INDICATOR LAMP (MIL) IS ON; THE TRANSMISSION IS STUCK IN THIRD GEAR; AND / OR THE INSTRUMENT CLUSTER IS INOPERATIVE. *TT

Showing 10 of the 12 you can open. Narrow the search to see the rest.