Skip to content
FaultCrate
日本語Open preview: everything readable

This is an open preview: every record can be read without an account. The details of the plans are in preparation.

GMC Yukon XL 2000–2006

GMC Yukon XLModel years 2000–2006

Change vehicle →
Clear the search
2 conditions added

Common on this vehicle:NoiseWarning lightVibration or shudderLeakLoss of engine power, no accelerationShifting faultCorrosion or rustStalls or shuts off

Possible causes

Transmission and driveline, 200430 records
Transmission and driveline
Engine
Exhaust and emissions
Suspension, wheels and tires
2Transmission14L60-E slip or no forward engagement right after input housing replacement (service part 17803687)14L80-E / 4L85-E planetary gear whine in first and second gear1Single-cylinder misfire (P0300-P0308) and/or chirp, squeak or tick at camshaft speed: worn cam lobe / lifter, valve or valve spring1P0420 / P0430 on a new or just-replaced catalytic converter (break-in not completed)1Hub Assembly

The documents say what to doOnly records name itThe size of a node, the width of a link and the numbers are records matching this search, not likelihoods.

FaultCrate・GMC Yukon XL 2000–2006・Transmission and driveline, 2004

Candidate cause (the documents say what to do)

4L60-E slip or no forward engagement right after input housing replacement (service part 17803687)

A few transmissions may slip or not engage any forward gear immediately after the input housing is replaced.

The input housing from GM Service Parts may have an incorrectly drilled input shaft.

What to do

  1. Inspect the 3-4 clutch and forward clutch oil feed passages for leakage between circuits.
  2. With the Input Housing (621) completely assembled, apply regulated compressed air to the 3-4 clutch feed hole and the forward clutch feed hole one at a time.
  3. Air should not leak out of the 3-4 clutch feed hole when air is applied to the forward clutch feed hole, and not out of the forward clutch feed hole when air is applied to the 3-4 clutch feed hole.
  4. Order new housing part number 19125752.
  5. Part number 19125752, Input Housing And Turbine Shaft Assembly, quantity 1.

Caution: Do not replace an input housing solely because of a small air leak between the shaft and housing.

Part numbers printed in the document

The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

In the records

  • Input Housing: replaced 1
See the evidence (2 technical documents, 1 records)

Passages of the technical documents

  • 1999-2006 GMC Savana, Sierra, Yukon, Yukon XL

    General Motors (published by NHTSA) 2012-10-30

  • This information only applies to Input Housing (621) with Service Part Number 17803687.

    General Motors (published by NHTSA) 2012-10-30

  • A few transmissions may experience a condition of slip or no engagement to any forward gear immediately after replacing the Input Housing (621).

    General Motors (published by NHTSA) 2012-10-30

  • The Input Housing (621) from GM Service Parts may have an incorrectly drilled input shaft.

    General Motors (published by NHTSA) 2012-10-30

Read every statement and its source →

Manufacturer’s documents

Records

None among the records that can be opened now.

See all 1 records of this cause →

A cause or a result a complaint states is the owner’s view or what a dealer told them, not an established fact.

Put together by FaultCrate from public records and technical documents. The cause and the repair are for the workshop to decide with the vehicle in front of it. Counts are records, not failure rates.