Skip to content
FaultCrate
日本語Open preview: everything readable

This is an open preview: every record can be read without an account. The details of the plans are in preparation.

GMC Yukon 2000–2006

GMC YukonModel years 2000–2006

Change vehicle →
Clear the search
2 conditions added

Common on this vehicle:NoiseWarning lightCorrosion or rustLeakMisfire or rough idleAir conditioning or heaterReduced brakingLights (headlights, turn signals)

Record by record

12 records state a cause or a remedy. Each record is shown as short labels in the order fault → finding the cause → correction. Press a label to narrow to the records that state it.

Symptom

Component named as the cause

Work done

A ribbon is as wide as the records that state both of its ends (only the commonest are drawn). A record that names several symptoms or components runs through each. Orange is records that say the fault came back or was not fixed. Results come from owners’ reports only; one that does not say is “result not stated”. None of this is a likelihood of a cause or a rate at which work succeeds.

Read the records one by one (6)

Known issuesOut of fuel with the gauge reading above empty, cranks but no start, stall (replace the fuel sensor, not the sender module)1

  1. Manufacturer communication2001–2005 GMC FULL SIZE PICKUPS AND UTILITIES (YUKON) ・ 2005-12-01

    Cranks but no start, stall, or inaccurate fuel gauge with the tank out of fuel: replace the fuel sensor

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      Repair

      • Replace the fuel sensor.

      Caution

      • Do not replace the fuel sender module; the reference is bulletin 04-08-49-018E.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Row for 2001-2005 Full Size Pickups and Utilities: cranks but no start, stall, inaccurate/incorrect fuel gauge reading, no fuel, vehicle is out of fuel and the fuel gauge reads above empty.
    • Repair：Replace the fuel sensor.
    • Caution：Do not replace the fuel sender module; the reference is bulletin 04-08-49-018E.

    Open this issue of GM TechLink ↗ The points above are read from an article of TechLink, GM’s monthly publication for dealership technicians. The article itself is not reproduced here.

    Remedy
    Truck Issues — Fix It Right the First Time (new issues in bold) 2001-2005 Full Size Pickups and Utilities – Cranks But No Start, Stall, Inaccurate/Incorrect Fuel Gauge Reading, No Fuel, Vehicle is Out of Fuel and Fuel Gauge Reads Above Empty Replace fuel sensor. Don’t replace fuel sender module. 04-08-49-018E

ENGINE3

  1. Manufacturer communication2000–2006 GMC YUKON DENALI ・ 2024-07-16(5 earlier editions of this document folded here)

    Fuel Injection Cleaner Kit Service Bulletin

    1. 1Fault

      • Rough idle, crank no start, extended crank or misfire, with the engine warning lamp on and DTC P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308 set.
      • When the engine is cold, compression on multiple cylinders may be zero.
      • The engine may pop through the intake or exhaust while cranking, and the spark plugs may be fuel fouled.

    2. 2Finding the cause

      Possible causes

      • Major carbon build-up on the intake and/or exhaust valves from fuel contamination or incomplete burning of the fuel; misfires should not appear before at least 8,000 km (5,000 mi).

    3. 3Correction

      Repair

      1. If there is no valve damage and no cam follower out of place, perform the cleaning procedure to free sticking valves and remove carbon from the valves and pistons.
      2. If valves are damaged or cam followers are out of place, make the engine mechanical repairs first and then perform the cleaning procedure to prevent a return.
      3. Fill Cleaner Kit J-35800-A with about 650 ml (22 oz, 2 cans) of Air Intake, Combustion Chamber Cleaner and set the air pressure at the tool to 260 kPa (40 psi).
      4. With GDS 2 or a scan tool, command engine idle to 2000 rpm so the engine does not stall.
      5. With the engine at operating temperature in a well-ventilated area, slowly and carefully induce the cleaner into the engine, taking about 3 minutes.

      Parts

      • The Top Engine Cleaning Kit (ACDelco Air Intake, Valve and Combustion Chamber Cleaner and ACDelco Fuel System Cleaner 44K) is 19435372 for the U.S. and Canada.

      Part numbers printed in the document

      The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

      Caution

      • Inducing too much cleaner at too low an RPM, or stalling the engine with too much cleaner at once, may hydro-lock the engine and bend a connecting rod.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to GM passenger cars and trucks with gasoline engines only, model years 2000 to 2025.
    • Condition：Rough idle, crank no start, extended crank or misfire, with the engine warning lamp on and DTC P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308 set.
    • Condition：When the engine is cold, compression on multiple cylinders may be zero.
    • Condition：The engine may pop through the intake or exhaust while cranking, and the spark plugs may be fuel fouled.
    • Cause：Major carbon build-up on the intake and/or exhaust valves from fuel contamination or incomplete burning of the fuel; misfires should not appear before at least 8,000 km (5,000 mi).
    • Repair：If there is no valve damage and no cam follower out of place, perform the cleaning procedure to free sticking valves and remove carbon from the valves and pistons.
    • Repair：If valves are damaged or cam followers are out of place, make the engine mechanical repairs first and then perform the cleaning procedure to prevent a return.
    • Caution：Inducing too much cleaner at too low an RPM, or stalling the engine with too much cleaner at once, may hydro-lock the engine and bend a connecting rod.
    • Repair：Fill Cleaner Kit J-35800-A with about 650 ml (22 oz, 2 cans) of Air Intake, Combustion Chamber Cleaner and set the air pressure at the tool to 260 kPa (40 psi).
    • Repair：With GDS 2 or a scan tool, command engine idle to 2000 rpm so the engine does not stall.
    • Repair：With the engine at operating temperature in a well-ventilated area, slowly and carefully induce the cleaner into the engine, taking about 3 minutes.
    • Parts：The Top Engine Cleaning Kit (ACDelco Air Intake, Valve and Combustion Chamber Cleaner and ACDelco Fuel System Cleaner 44K) is 19435372 for the U.S. and Canada.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This service bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.

  2. Manufacturer communication2000–2006 GMC YUKON DENALI ・ 2017-08-15(1 earlier editions of this document folded here)

    Engine Misfire and Rough Idle Malfunction Indicator Lamp

    1. 1Fault

      • Customers may complain of a MIL and/or engine misfire, rough idle, extended crank, or crank no start.
      • One or more misfire codes (DTC P0300-P0308) are found stored in the ECM.

    2. 2Finding the cause

      Possible causes

      • The condition may result from major carbon build up on the intake and/or exhaust valves due to fuel contamination or incomplete burning of the fuel.

      Steps to confirm (in the document’s order)

      1. With the engine cold, compression on multiple cylinders may read 0 PSI (= 0 kPa).
      2. The engine may pop through the intake or exhaust while cranking, and the spark plugs may be fuel fouled.

    3. 3Correction

      Repair

      1. If there is valve damage or cam followers are out of place, make the mechanical repairs first, then perform the cleaning procedure to keep the concern from returning.
      2. With the engine at operating temperature, slowly induce a bottle of GM Upper Engine and Fuel Injection Cleaner with RPM held above idle so the engine does not stall (typically around 2,000 RPM).
      3. Turn the engine off and let the cleaner soak for 2.5 to 3 hours.
      4. To complete the repair, change the engine oil and filter.

      Parts

      • Upper Engine and Fuel Injector Cleaner is P/N 88861803 (in Canada, P/N 88861804).

      Part numbers printed in the document

      The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

      Caution

      • Inducing too much cleaner at too low an RPM, or stalling the engine with cleaner, may hydro-lock the engine and bend a connecting rod.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to all 2000-2015 light duty trucks with gasoline engines.
    • Condition：Customers may complain of a MIL and/or engine misfire, rough idle, extended crank, or crank no start.
    • Condition：One or more misfire codes (DTC P0300-P0308) are found stored in the ECM.
    • Cause：The condition may result from major carbon build up on the intake and/or exhaust valves due to fuel contamination or incomplete burning of the fuel.
    • Confirm：With the engine cold, compression on multiple cylinders may read 0 PSI (= 0 kPa).
    • Confirm：The engine may pop through the intake or exhaust while cranking, and the spark plugs may be fuel fouled.
    • Repair：If there is valve damage or cam followers are out of place, make the mechanical repairs first, then perform the cleaning procedure to keep the concern from returning.
    • Repair：With the engine at operating temperature, slowly induce a bottle of GM Upper Engine and Fuel Injection Cleaner with RPM held above idle so the engine does not stall (typically around 2,000 RPM).
    • Repair：Turn the engine off and let the cleaner soak for 2.5 to 3 hours.
    • Repair：To complete the repair, change the engine oil and filter.
    • Caution：Inducing too much cleaner at too low an RPM, or stalling the engine with cleaner, may hydro-lock the engine and bend a connecting rod.
    • Parts：Upper Engine and Fuel Injector Cleaner is P/N 88861803 (in Canada, P/N 88861804).

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed.

  3. Manufacturer communication2000–2006 GMC YUKON DENALI ・ 2017-05-16

    Engine Misfire and Rough Idle Diagnostic Communication

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE A MALFUNCTION INDICATOR LAMP ON OR ENGINE MISFIRE, ROUGH IDLE, EXTENDED CRANK, OR CRANK NO START IN SOME CASES. TECHNICIAN WILL NEED TO PERFORM PUBLISHED SERVICE INFORMATION DIAGNOSTICS. IF TECHNICIAN FINDS CARBON, AN UPPER ENGINE AND VALVE CLEANING SHOULD BE PERFORMED.

    Read the sentences of the record
    Remedy
    THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE A MALFUNCTION INDICATOR LAMP ON OR ENGINE MISFIRE, ROUGH IDLE, EXTENDED CRANK, OR CRANK NO START IN SOME CASES. TECHNICIAN WILL NEED TO PERFORM PUBLISHED SERVICE INFORMATION DIAGNOSTICS. IF TECHNICIAN FINDS CARBON, AN UPPER ENGINE AND VALVE CLEANING SHOULD BE PERFORMED.

ENGINE AND ENGINE COOLING2

  1. Manufacturer communication2000–2004 GMC YUKON ・ 2005-03-11

    Diagnostic Information for Intermittent Vehicle No Crank Dead Battery

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      DIAGNOSTIC INFORMATION FOR INTERMITTENT VEHICLE NO CRANK DEAD BATTERY. *EH

    Read the sentences of the record
    Remedy
    DIAGNOSTIC INFORMATION FOR INTERMITTENT VEHICLE NO CRANK DEAD BATTERY. *EH

  2. Manufacturer communication2002–2004 GMC YUKON ・ 2004-08-13

    Flexible Fuel Vehicle Starting, Stalling, Power Loss and Performance Issues

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      VEHICLE WITH FLEXIBLE FUEL WILL NOT START, STALLS AND WILL NOT RESTART, LOSS OF POWER, POOR PERFORMANCE. *TT POOR PERFORMANCE AND/OR FUEL GAUGE READS INACCURATE/INCORRECT. *TT

    Read the sentences of the record
    Remedy
    VEHICLE WITH FLEXIBLE FUEL WILL NOT START, STALLS AND WILL NOT RESTART, LOSS OF POWER, POOR PERFORMANCE. *TT POOR PERFORMANCE AND/OR FUEL GAUGE READS INACCURATE/INCORRECT. *TT

Showing 6 of the 12 you can open. Narrow the search to see the rest.