GMC Yukon 2000–2006
Common on this vehicle:Gauge or instrument faultNoiseWarning lightCorrosion or rustLeakReduced brakingAir conditioning or heaterVibration or shudder
Possible causes
22 causes not drawn
- Crankshaft position sensor may work intermittently or fail (8.1L V8) - recall 07V-5218.1L only0
- Throttle body carbon build-up: idle surge, reduced engine power, throttle DTCs (high mileage)0
- Front right-hand brake pipe contact with body cross sill - recall 00V-3450
- Stability System Disabled message and unwanted StabiliTrak activation (tire wear or mismatched tires)0
- ABS lamp with DTC C0265 (EBCM motor relay circuit) after EBCM replacement0
- Autoride (Z55) Service Ride Control / Service Suspension System message2
- Aluminum Wheel Bead Seat: corroded2
- Aftermarket part (not the vehicle as built): Federal-Mogul National / Carquest replacement wheel hub assembly retention nut - recall 07E-1062WD only1
- Rear door window inoperative (motor replacement)1
- Power Window: failed1
- Sunroof: failed1
- Service 4WD indicator and DTC B2725 (transfer case shift control switch)4WD / AWD only1
- 4WD/AWD lamps and system inoperative: "sleepy" New Venture Gear transfer case control module (reprogram the TCCM)4WD / AWD only1
- Transfer case service light, New Venture Gear transfer case (replace the encoder motor sensor and reprogram the TCCM)0
- Transfer Case Speed Sensor Wiring Harness: electrical fault1
- Rear HVAC ticking noise, no rear temperature or mode control, DTC B0434 / B3764 (revised auxiliary HVAC control module)1
- Seat Heater: overheated1
- No response when the OnStar button is pressed (DTC B2476): button assembly test values1
- Red OnStar LED and DTC B2455 after Canada upgrade bulletin 15-08-44-001 (audio and microphone drain wires shorted)1
- Instrument panel cluster gauges stick, flutter or stop working1
- CHECK OIL LEVEL message stays on after an oil change or top-off until the engine cools0
- Quadrasteer: rear wheels stay turned after the front wheels are straight (controlled re-centering after a fault, normal operation)1
Causes with no correction stated (23)
Causes the records name for which no check or repair is stated, in a technical document or in a record. Press one for the records that name it.
- Electrical, wiring and power
- ATC Fuse: electrical fault, failed (2)Bulb Socket: overheated (1)Powertrain Control Module: software (1)Intermittent no start with Service Stability, ABS light, 'Unknown Driver' and multiple DTCs / no module communication (0)
- Brakes
- Wheel Speed Sensor: failed (2)Service Stability message with DTC C0131, C0196, C0290 and/or C0292 (1)Anti-Lock Brake Motor: failed (1)Anti-Lock Brake Pump: failed (1)
- Airbags and seat belts
- Airbag: failed (1)Airbag Sensor: failed (1)
- Instruments and lighting
- Bulb: failed (1)Instrument Panel Cluster: failed (1)
- Heating and air conditioning
- Encoder Motor: electrical fault (1)
- Exhaust and emissions
- Evap Vent Valve: clogged or contaminated (1)Exhaust Manifold Bolt: broken (1)Secondary Air Injection Valve: corroded (1)
- Fuel system
- Fuel Tank: leaking (1)
- Audio and telematics
- OnStar System: failed (1)
- Body, doors and interior
- Seat Position Sensor: broken (1)
- Suspension, wheels and tires
- Shock: failed (1)
- Transmission and driveline
- Transmission: failed (1)Transmission Control Module: failed (1)Transmission Range Switch: failed (1)
The documents say what to doOnly records name itThe size of a node, the width of a link and the numbers are records matching this search, not likelihoods.
FaultCrate・GMC Yukon 2000–2006・Warning light
Candidate cause (the documents say what to do)
Intake manifold gasket leak (cold idle misfire, lean codes)
The bulletin describes a cold engine idle misfire with DTCs P0171, P0174 or P0300.
The bulletin states the intake gasket seals may leak around the intake ports, causing the lean condition.
How to tell
P0171P0174P0300Check engine / Service Engine Soon
What to do
- The seals may leak around the bottom side of the port, which makes the vacuum leak hard to detect.
- Lower-than-normal MAF readings may be seen if the intake seals are leaking.
- An intake manifold with warpage in excess of 3mm (.118 in.) over a 200mm (7.87-in.) area must be replaced.
- Measure the intake manifold for warpage across two runner ports only.
- Only the current teal green gaskets should be used; the old gaskets were orange.
- The intake bolts must be replaced and not reused.
Caution: Do not measure the intake manifold across all four intake runner ports.
What is needed
- Parts and materials
- Intake manifold gasket GM SPO p/n 89017589 (teal green; the only one to use for repairs on the L59 engine)
- Intake manifold gaskets (the current teal green ones)
- Intake bolts (not to be reused)
- Intake manifold (when warped in excess of 3mm (.118 in.) over a 200mm (7.87-in.) area)
Part numbers printed in the document
The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.
- Labor time
- Not stated
- Special tools
- Not stated
- Scan tool
- Not stated
Only what the technical documents state. "Not stated" does not mean not needed.
In the records
No record states work done for this cause.
See the evidence (1 technical documents, 10 records)
Passages of the technical documents
MOTOR reports the GM bulletin lists 1999-2005 GMC Savana, Sierra and Yukon models among affected vehicles.
Affected vehicles include 2002-05 Cadillac Escalades, 1999-2005 Chevrolet Avalanche, Express, Silverado, Suburban, Tahoe and Trailblazer models, 1999-2005 GMC Savana, Sierra and Yukon models, and 2003-05 HUMMER H2s.
MOTOR Magazine 2017-02-06
The bulletin describes a cold engine idle misfire with DTCs P0171, P0174 or P0300.
It describes a cold engine idle misfire, with DTCs P0171 P0174 or P0300.
MOTOR Magazine 2017-02-06
The bulletin states the intake gasket seals may leak around the intake ports, causing the lean condition.
The TSB states that the intake gasket seals may be leaking around the intake ports, causing the lean condition.
MOTOR Magazine 2017-02-06
Leaks typically occur when the engine is cold and may subside as it warms.
Leaks typically occur when the engine is cold, and may subside as the engine warms.
MOTOR Magazine 2017-02-06
A cause or a result a complaint states is the owner’s view or what a dealer told them, not an established fact.
Put together by FaultCrate from public records and technical documents. The cause and the repair are for the workshop to decide with the vehicle in front of it. Counts are records, not failure rates.