GMC Yukon 2000–2006
Common on this vehicle:Gauge or instrument faultNoiseWarning lightCorrosion or rustLeakReduced brakingAir conditioning or heaterVibration or shudder
Possible causes
21 causes not drawn
- Crankshaft position sensor may work intermittently or fail (8.1L V8) - recall 07V-5218.1L only0
- Throttle body carbon build-up: idle surge, reduced engine power, throttle DTCs (high mileage)0
- Front right-hand brake pipe contact with body cross sill - recall 00V-3450
- Stability System Disabled message and unwanted StabiliTrak activation (tire wear or mismatched tires)0
- ABS lamp with DTC C0265 (EBCM motor relay circuit) after EBCM replacement0
- Autoride (Z55) Service Ride Control / Service Suspension System message2
- Aluminum Wheel Bead Seat: corroded2
- Aftermarket part (not the vehicle as built): Federal-Mogul National / Carquest replacement wheel hub assembly retention nut - recall 07E-1062WD only1
- Rear door window inoperative (motor replacement)1
- Power Window: failed1
- Sunroof: failed1
- Service 4WD indicator and DTC B2725 (transfer case shift control switch)4WD / AWD only1
- 4WD/AWD lamps and system inoperative: "sleepy" New Venture Gear transfer case control module (reprogram the TCCM)4WD / AWD only1
- Transfer Case Speed Sensor Wiring Harness: electrical fault1
- Rear HVAC ticking noise, no rear temperature or mode control, DTC B0434 / B3764 (revised auxiliary HVAC control module)1
- Seat Heater: overheated1
- No response when the OnStar button is pressed (DTC B2476): button assembly test values1
- Red OnStar LED and DTC B2455 after Canada upgrade bulletin 15-08-44-001 (audio and microphone drain wires shorted)1
- Instrument panel cluster gauges stick, flutter or stop working1
- CHECK OIL LEVEL message stays on after an oil change or top-off until the engine cools0
- Quadrasteer: rear wheels stay turned after the front wheels are straight (controlled re-centering after a fault, normal operation)1
Causes with no correction stated (23)
Causes the records name for which no check or repair is stated, in a technical document or in a record. Press one for the records that name it.
- Electrical, wiring and power
- ATC Fuse: electrical fault, failed (2)Bulb Socket: overheated (1)Powertrain Control Module: software (1)Intermittent no start with Service Stability, ABS light, 'Unknown Driver' and multiple DTCs / no module communication (0)
- Brakes
- Wheel Speed Sensor: failed (2)Service Stability message with DTC C0131, C0196, C0290 and/or C0292 (1)Anti-Lock Brake Motor: failed (1)Anti-Lock Brake Pump: failed (1)
- Airbags and seat belts
- Airbag: failed (1)Airbag Sensor: failed (1)
- Instruments and lighting
- Bulb: failed (1)Instrument Panel Cluster: failed (1)
- Heating and air conditioning
- Encoder Motor: electrical fault (1)
- Exhaust and emissions
- Evap Vent Valve: clogged or contaminated (1)Exhaust Manifold Bolt: broken (1)Secondary Air Injection Valve: corroded (1)
- Fuel system
- Fuel Tank: leaking (1)
- Audio and telematics
- OnStar System: failed (1)
- Body, doors and interior
- Seat Position Sensor: broken (1)
- Suspension, wheels and tires
- Shock: failed (1)
- Transmission and driveline
- Transmission: failed (1)Transmission Control Module: failed (1)Transmission Range Switch: failed (1)
The documents say what to doOnly records name itThe size of a node, the width of a link and the numbers are records matching this search, not likelihoods.
FaultCrate・GMC Yukon 2000–2006・Warning light
Candidate cause (the documents say what to do)
Transfer case service light, New Venture Gear transfer case (replace the encoder motor sensor and reprogram the TCCM)
0 of the records matching this search name this component as the cause.
How to tell
C0327P0500P0836Service 4WD
What to do
- Verify that the encoder motor is the primary cause.
- Replace the encoder motor sensor and reprogram the TCCM; the labor operation is K9980.
Caution: Do not replace the module, the encoder motor or the transfer case for DTCs C0327, P0836, P0500; the reference is bulletin 03-04-21-001D.
What is needed
- Parts and materials
- Encoder motor sensor
- Labor time
- Labor Operation: K9980
- Special tools
- Not stated
- Scan tool
- Reprogramming of the TCCM
Only what the technical documents state. "Not stated" does not mean not needed.
In the records
No record states work done for this cause.
See the evidence (1 technical documents, 0 records)
Passages of the technical documents
Row for 2003 Fullsize Pickups and Utilities: transfer case service light, New Venture Gear transfer case.
2003 Fullsize Pickups and Utilities – Transfer Case Service Light/New Venture Gear Transfer Case
General Motors 2004-04-01
Verify that the encoder motor is the primary cause.
Verify that the encoder motor is the primary cause.
General Motors 2004-04-01
Replace the encoder motor sensor and reprogram the TCCM; the labor operation is K9980.
Replace encoder motor sensor and reprogram TCCM. Labor Operation: K9980
General Motors 2004-04-01
Do not replace the module, the encoder motor or the transfer case for DTCs C0327, P0836, P0500; the reference is bulletin 03-04-21-001D.
Don’t replace the module, encoder motor or transfer case for DTCs C0327, P0836, P0500 03-04-21-001D
General Motors 2004-04-01
A cause or a result a complaint states is the owner’s view or what a dealer told them, not an established fact.
Put together by FaultCrate from public records and technical documents. The cause and the repair are for the workshop to decide with the vehicle in front of it. Counts are records, not failure rates.