GMC Yukon 2000–2006
Common on this vehicle:Warning lightNoiseLeakGauge or instrument faultAir conditioning or heaterVibration or shudderLoss of engine power, no accelerationSeat belt
Possible causes
15 causes not drawn
- P0300 after engine repairs: injector connectors crossed (cylinders 5-7 / 6-8)0
- Rear bank knock sensor corrosion from water intrusion (P0332)4.8L, 5.3L, 6.0L only0
- Throttle body carbon build-up: idle surge, reduced engine power, throttle DTCs (high mileage)0
- Brake pipe (brake line) corrosion and rupture0
- ABS light with C0265/C0201/U1041 or no communication with brake module (EBCM ground G110)0
- Front right-hand brake pipe contact with body cross sill - recall 00V-3450
- Service Brake Booster message on a Hydroboost vehicle with DTC C0136 (instrument cluster not SPS programmed)0
- Stability System Disabled / Service Stability message with DTC C0455 (bent terminals at the steering wheel position sensor)0
- Stability System Disabled message and unwanted StabiliTrak activation (tire wear or mismatched tires)0
- ABS lamp with DTC C0265 (EBCM motor relay circuit) after EBCM replacement0
- Transfer case service light, New Venture Gear transfer case (replace the encoder motor sensor and reprogram the TCCM)0
- Transfer Case Speed Sensor Wiring Harness: electrical fault1
- Seat Heater: overheated1
- DTC P0446 set with the SES lamp on (replace the EVAP vent solenoid, not the canister)0
- CHECK OIL LEVEL message stays on after an oil change or top-off until the engine cools0
Causes with no correction stated (23)
Causes the records name for which no check or repair is stated, in a technical document or in a record. Press one for the records that name it.
- Electrical, wiring and power
- ATC Fuse: electrical fault, failed (2)Bulb Socket: overheated (1)Powertrain Control Module: software (1)Intermittent no start with Service Stability, ABS light, 'Unknown Driver' and multiple DTCs / no module communication (0)
- Brakes
- Wheel Speed Sensor: failed (2)Anti-Lock Brake Motor: failed (1)Anti-Lock Brake Pump: failed (1)Service Stability message with DTC C0131, C0196, C0290 and/or C0292 (0)
- Airbags and seat belts
- Airbag: failed (1)Airbag Sensor: failed (1)
- Instruments and lighting
- Bulb: failed (1)Instrument Panel Cluster: failed (1)
- Heating and air conditioning
- Encoder Motor: electrical fault (1)
- Exhaust and emissions
- Evap Vent Valve: clogged or contaminated (1)Exhaust Manifold Bolt: broken (1)Secondary Air Injection Valve: corroded (1)
- Fuel system
- Fuel Tank: leaking (1)
- Audio and telematics
- OnStar System: failed (1)
- Body, doors and interior
- Seat Position Sensor: broken (1)
- Suspension, wheels and tires
- Shock: failed (1)
- Transmission and driveline
- Transmission: failed (1)Transmission Control Module: failed (1)Transmission Range Switch: failed (1)
The documents say what to doOnly records name itThe size of a node, the width of a link and the numbers are records matching this search, not likelihoods.
FaultCrate・GMC Yukon 2000–2006・Warning light
Candidate cause (named by records only; no technical document)
Electronic Brake Control Module: failed
1 of the records matching this search name this component as the cause.
How to tell
ABS light
What to do
No technical document states a check or a repair.
In the records
- Electronic Brake Control Module: replaced 1（says it came back: 1）
See the evidence (0 technical documents, 1 records)
A cause or a result a complaint states is the owner’s view or what a dealer told them, not an established fact.
Put together by FaultCrate from public records and technical documents. The cause and the repair are for the workshop to decide with the vehicle in front of it. Counts are records, not failure rates.