Skip to content
FaultCrate
日本語Open preview: everything readable

This is an open preview: every record can be read without an account. The details of the plans are in preparation.

GMC Yukon 2000–2006

GMC YukonModel years 2000–2006

Change vehicle →
Clear the search
1 conditions added

Common on this vehicle:Warning light

Record by record

9 records state a cause or a remedy. Each record is shown as short labels in the order fault → finding the cause → correction. Press a label to narrow to the records that state it.

Symptom

Component named as the cause

Work done

A ribbon is as wide as the records that state both of its ends (only the commonest are drawn). A record that names several symptoms or components runs through each. Orange is records that say the fault came back or was not fixed. Results come from owners’ reports only; one that does not say is “result not stated”. None of this is a likelihood of a cause or a rate at which work succeeds.

Read the records one by one (4)

Known issuesAutoride (Z55) Service Ride Control / Service Suspension System message2

  1. Manufacturer communication2001–2006 GMC YUKON DENALI ・ 2013-08-06

    Service Suspension System Display - Trim Height/Compressor Issue

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      GM: IF THE SERVICE SUSPENSION SYSTEM IS DISPLAYED ON THE DIC, THE TRIM HEIGHT MAY BE INCORRECT, LOOSE COMPRESSOR INLET HOSE, OR THE COMPRESSOR SELF TEST MAY BE INOPERATIVE. ALSO INCLUDED SUBURBAN LD MY 2001-2013, YUKON DENALI XL MY 2013, YUKON XL LD 2001-2013 *JS

      What the documents say to do

      Autoride (Z55) Service Ride Control / Service Suspension System message

      Confirm

      • The compressor assembly may need to be removed to see whether the wiring is pinched between the compressor and the frame.

      Repair

      1. Repair the damaged or shorted circuits and reposition the wiring so it is not damaged again when the compressor is installed.
      2. The sensor is not serviced separately; install a complete air filter, dryer and sensor assembly.

      Caution

      • Do not replace the complete air compressor assembly for this concern.
    Read the sentences of the record
    Remedy
    GM: IF THE SERVICE SUSPENSION SYSTEM IS DISPLAYED ON THE DIC, THE TRIM HEIGHT MAY BE INCORRECT, LOOSE COMPRESSOR INLET HOSE, OR THE COMPRESSOR SELF TEST MAY BE INOPERATIVE. ALSO INCLUDED SUBURBAN LD MY 2001-2013, YUKON DENALI XL MY 2013, YUKON XL LD 2001-2013 *JS

  2. Manufacturer communication2001–2003 GMC YUKON ・ 2005-03-07

    Ride Control Message and DTC C0580 Service Communication

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

    Read the sentences of the record
    Remedy
    SERVICE RIDE CONTROL MESSAGE DISPLAYED DIAGNOSTIC TROUBLE CODE C0580 SET REPLACE RIGHT FRONT SHOCK ADSORBER SOLENOID CONNECTOR AND INSTALL NEW AC SUCTION HOSE AND AUXILIARY AC EVAPORATOR HOSE. *EH

ELECTRICAL SYSTEM1

  1. Manufacturer communication2006 GMC YUKON ・ 2024-05-06(2 earlier editions of this document folded here)

    Magnetically Controlled Suspension Electrical Connector Not Seated

    1. 1Fault

      • The subject names a Service Suspension System message with DTCs C0575, C0580, C0585 or C0590.
      • Some customers may comment on a Service Suspension System message displayed on the Drivers Information Center (DIC).

    2. 2Finding the cause

      Possible causes

      • During assembly, the 90 degree electrical connector at the top end of a shock absorber (actuator) may not have been fully seated, or may have been bumped firmly enough to partially disconnect it or create an internal contact concern.

      Steps to confirm (in the document’s order)

      1. Visually examine the green insulator and center post of the electrical connector to make sure it is straight and in serviceable condition; replace the connector and retest if required.
      2. Reconnect the electrical connector to the shock absorber (actuator), clear the suspension DTC and confirm that the code does not reset.
      3. If the code returns, remove the electrical connector from the shock absorber (actuator) and pigtail, and swap it with the connector on the opposite side shock absorber (actuator).

    3. 3Correction

      Repair

      • If the DTC follows the connector to the other side, replace the connector; if not, refer to SI and follow the diagnostics for the DTC originally found.

      Parts

      • Part number 19180262, Connector, S/ABS Elec Susp Control.

      Part numbers printed in the document

      The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

      Caution

      • Complete the document's steps before attempting shock absorber (actuator) replacement.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：The model list includes the 2006-2014 GMC Yukon and Yukon XL.
    • Applies to：It applies to vehicles equipped with RPO F55, Z55 or Z95.
    • Condition：The subject names a Service Suspension System message with DTCs C0575, C0580, C0585 or C0590.
    • Condition：Some customers may comment on a Service Suspension System message displayed on the Drivers Information Center (DIC).
    • Cause：During assembly, the 90 degree electrical connector at the top end of a shock absorber (actuator) may not have been fully seated, or may have been bumped firmly enough to partially disconnect it or create an internal contact concern.
    • Caution：Complete the document's steps before attempting shock absorber (actuator) replacement.
    • Confirm：Visually examine the green insulator and center post of the electrical connector to make sure it is straight and in serviceable condition; replace the connector and retest if required.
    • Confirm：Reconnect the electrical connector to the shock absorber (actuator), clear the suspension DTC and confirm that the code does not reset.
    • Confirm：If the code returns, remove the electrical connector from the shock absorber (actuator) and pigtail, and swap it with the connector on the opposite side shock absorber (actuator).
    • Repair：If the DTC follows the connector to the other side, replace the connector; if not, refer to SI and follow the diagnostics for the DTC originally found.
    • Parts：Part number 19180262, Connector, S/ABS Elec Susp Control.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    Magnetically Controlled Suspension Electrical Connector Not Seated.

SUSPENSION1

  1. Manufacturer communication2001–2006 GMC YUKON DENALI ・ 2023-12-26(3 earlier editions of this document folded here)

    Suspension Service Communication

    1. 1Fault

      • Condition 1 (2009 or prior vehicles): a Service Suspension System message on the DIC with incorrect rear ride height, and DTC C0696 or C0711 set in the Electronic Suspension Control (ESC) module.
      • Condition 2: a Service Suspension System message on the DIC, possibly with low rear ride height under a heavy payload, and DTC C0711 set in the ESC module.
      • Condition 3: a loose hose hangs down at the left rear; upon inspection the hose may be found damaged or disconnected from the air inlet filter of the auto leveling suspension air compressor.

    2. 2Finding the cause

      Possible causes

      • Condition 1 can be caused by the wiring to the automatic level control (ALC) pressure sensor being shorted to ground.
      • Condition 2 may be caused by an internal fault in the ALC pressure sensor, which can occur when moisture gets into the sensor.

      Steps to confirm (in the document’s order)

      1. The air compressor assembly may have to be removed to see whether the wiring is pinched between the compressor assembly and the frame.
      2. If system pressure at start up is below 10 psi (69 kpa), the system runs the compressor to add air to the shocks as a replenishment cycle.

    3. 3Correction

      Repair

      1. For condition 1, repair any damaged or shorted circuits and reposition the wiring so it is not damaged again when the compressor assembly is installed.
      2. The sensor is no longer serviced separately; to replace it, install a complete air filter, dryer and sensor assembly.
      3. For condition 3, replace the auto leveling compressor air inlet filter and hose assembly (PN 22197160).

      Part numbers printed in the document

      The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

      Parts

      • Vehicles built before May, 2012 need a jumper harness for the updated sensor, which is included with assembly PN 22964558; vehicles built in May, 2012 and later need no jumper harness and use PN 22941807.

      Part numbers printed in the document

      The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

      Caution

      • Do not replace the complete air compressor assembly for this concern.
      • Condition 4 (no compressor self test at start up): the automatic level system normally does not, or only very infrequently does, cycle the compressor at key up.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to 2001-2013 GMC Yukon, Yukon XL LD, Yukon Denali and Yukon Denali XL (note: the years run later than the years this service covers).
    • Applies to：Vehicles with RPO Z55 or Z95 are covered.
    • Condition：Condition 1 (2009 or prior vehicles): a Service Suspension System message on the DIC with incorrect rear ride height, and DTC C0696 or C0711 set in the Electronic Suspension Control (ESC) module.
    • Cause：Condition 1 can be caused by the wiring to the automatic level control (ALC) pressure sensor being shorted to ground.
    • Confirm：The air compressor assembly may have to be removed to see whether the wiring is pinched between the compressor assembly and the frame.
    • Repair：For condition 1, repair any damaged or shorted circuits and reposition the wiring so it is not damaged again when the compressor assembly is installed.
    • Caution：Do not replace the complete air compressor assembly for this concern.
    • Condition：Condition 2: a Service Suspension System message on the DIC, possibly with low rear ride height under a heavy payload, and DTC C0711 set in the ESC module.
    • Cause：Condition 2 may be caused by an internal fault in the ALC pressure sensor, which can occur when moisture gets into the sensor.
    • Repair：The sensor is no longer serviced separately; to replace it, install a complete air filter, dryer and sensor assembly.
    • Parts：Vehicles built before May, 2012 need a jumper harness for the updated sensor, which is included with assembly PN 22964558; vehicles built in May, 2012 and later need no jumper harness and use PN 22941807.
    • Condition：Condition 3: a loose hose hangs down at the left rear; upon inspection the hose may be found damaged or disconnected from the air inlet filter of the auto leveling suspension air compressor.
    • Repair：For condition 3, replace the auto leveling compressor air inlet filter and hose assembly (PN 22197160).
    • Caution：Condition 4 (no compressor self test at start up): the automatic level system normally does not, or only very infrequently does, cycle the compressor at key up.
    • Confirm：If system pressure at start up is below 10 psi (69 kpa), the system runs the compressor to add air to the shocks as a replenishment cycle.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    Suspension.

Showing 4 of the 9 you can open. Narrow the search to see the rest.