Skip to content
FaultCrate
日本語Open preview: everything readable

This is an open preview: every record can be read without an account. The details of the plans are in preparation.

GMC Yukon 2000–2006

GMC YukonModel years 2000–2006

Change vehicle →
Clear the search
2 conditions added

Common on this vehicle:Loss of engine power, no accelerationWarning lightStalls or shuts offGauge or instrument faultLights (headlights, turn signals)OverheatingWipers

Record by record

14 records state a cause or a remedy. Each record is shown as short labels in the order fault → finding the cause → correction. Press a label to narrow to the records that state it.

Symptom

Component named as the cause

Work done

How it is said to have ended

  • says it held for a while1
  • says it came back1
  • says it did not fix it4

A ribbon is as wide as the records that state both of its ends (only the commonest are drawn). A record that names several symptoms or components runs through each. Orange is records that say the fault came back or was not fixed. Results come from owners’ reports only; one that does not say is “result not stated”. None of this is a likelihood of a cause or a rate at which work succeeds.

Read the records one by one (12)

Known issuesDTCs P2108, P1516 and U0107 (do not replace the TAC module)1

  1. Manufacturer communication2006 GMC YUKON ・ 2007-01-25

    LR4, LY2, L33, LH6, LM7, L59, LC9, LMG, LY5, LS2, LQ9, LQ4, L76, LY6 Throttle Actuator Control Module Communication

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      LR4, LY2, L33, LH6, LM7, L59, LC9, LMG, LY5, LS2, LQ9, LQ4, L76, LY6 THROTTLE ACTUATOR CONTROL (TAC). MODULE CODES, MIL/SES DTC'S P2108, P1516, U0107, REDUCED ENGINE POWER. *KB

      What the documents say to do

      DTCs P2108, P1516 and U0107 (do not replace the TAC module)

      Confirm

      • Perform the diagnostics for the DTCs, but delete the steps that involve replacing the TAC module.

      Caution

      • Do not replace the TAC module; the reference given is PIP 3812A.
    Read the sentences of the record
    Remedy
    LR4, LY2, L33, LH6, LM7, L59, LC9, LMG, LY5, LS2, LQ9, LQ4, L76, LY6 THROTTLE ACTUATOR CONTROL (TAC). MODULE CODES, MIL/SES DTC'S P2108, P1516, U0107, REDUCED ENGINE POWER. *KB

Known issuesReduced Engine Power from throttle body connector crimp, broken wire or grounds1

  1. Owner complaint2004 GMC YUKON DENALI ・ 2013-03-03

    Stability control disabled and reduced engine power warnings with 5 MPH speed limit on startup

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

    Read the sentences of the record
    Fault
    THE "STABILITY CONTROL DISABLED" SENSOR COMES ON FOLLOWED BY "REDUCED ENGINE POWER" AND MY VEHICLE WON'T GO FASTER THAN 5MPH (= 8.05 km/h). (1 more)
    Remedy
    THEY REPLACED THE "CONNECTOR AT THE THROTTLE BODY" AND CHARGED ME $223.09. (1 more)
    Outcome
    THE ISSUE TEMPORARILY WENT AWAY.

ELECTRICAL SYSTEM4

  1. Manufacturer communication2005–2006 GMC YUKON DENALI ・ 2018-06-04(1 earlier editions of this document folded here)

    IP to Body Harness Connector Repair for MIL and DTC P2138

    1. 1Fault

      • The engine warning lamp comes on intermittently with a message or indicator showing Reduced Engine Power.
      • DTC P2138 (Accelerator Pedal Position (APP) Sensor 1-2 Correlation) is set as current or in history.

    2. 2Finding the cause

      Possible causes

      • Water may have entered the instrument panel (IP) to body harness connector, which carries the APP sensor signals to the ECM/PCM.

      Steps to confirm (in the document’s order)

      1. Verify that no aftermarket equipment is electrically connected to the APP sensor signal or low reference circuits, or to any other ECM/PCM 5V reference or low reference circuit.
      2. Locate the IP to body harness connector, which may be in or around the left hand kick panel area or inside the IP.
      3. Inspect for a water leak in the area, using a water hose if necessary to find the source.
      4. Possible water leak points include the A-pillar seals, the sunroof drain lines (if equipped) and the windshield/cowl sealing.
      5. Inspect the terminals of the IP to body harness connector for corrosion and debris.

    3. 3Correction

      Repair

      1. If a water leak is found, repair it as necessary and verify that the repair is effective.
      2. If corrosion or debris is found on the connector terminals, repair as necessary.

      Caution

      • Aftermarket equipment can generate DTC P2138 and/or other DTCs.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to 2018 and prior GM passenger cars and light duty trucks.
    • Condition：The engine warning lamp comes on intermittently with a message or indicator showing Reduced Engine Power.
    • Condition：DTC P2138 (Accelerator Pedal Position (APP) Sensor 1-2 Correlation) is set as current or in history.
    • Cause：Water may have entered the instrument panel (IP) to body harness connector, which carries the APP sensor signals to the ECM/PCM.
    • Caution：Aftermarket equipment can generate DTC P2138 and/or other DTCs.
    • Confirm：Verify that no aftermarket equipment is electrically connected to the APP sensor signal or low reference circuits, or to any other ECM/PCM 5V reference or low reference circuit.
    • Confirm：Locate the IP to body harness connector, which may be in or around the left hand kick panel area or inside the IP.
    • Confirm：Inspect for a water leak in the area, using a water hose if necessary to find the source.
    • Confirm：Possible water leak points include the A-pillar seals, the sunroof drain lines (if equipped) and the windshield/cowl sealing.
    • Repair：If a water leak is found, repair it as necessary and verify that the repair is effective.
    • Confirm：Inspect the terminals of the IP to body harness connector for corrosion and debris.
    • Repair：If corrosion or debris is found on the connector terminals, repair as necessary.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC P2138 set.

  2. Manufacturer communication2005–2006 GMC YUKON DENALI ・ 2018-05-21(1 earlier editions of this document folded here)

    Throttle Position Sensor Cover Replacement

    1. 1Fault

      • The malfunction indicator lamp (MIL) is illuminated with a Reduced Engine Power message displayed.
      • A scan tool may show DTC P2135: Throttle Position (TP) Sensor 1-2 Correlation set as Current or in History.

    2. 2Finding the cause

      Possible causes

      • The condition may be caused by the difference between TP Sensor 1 and TP Sensor 2 exceeding a calibrated value for more than 2 seconds.

      Steps to confirm (in the document’s order)

      1. After installing the new cover, if the scan tool TP Sensor 1 and 2 Agree/Disagree parameter displays Disagree, replace the throttle body assembly.
      2. If DTC P1516, P2101 and/or P2176 are set, replace the throttle body.

    3. 3Correction

      Repair

      1. Clean the throttle body bore and throttle plate with a clean shop towel and GM Top Engine Cleaner, P/N 1052626 (in Canada, P/N 993026), or ACDelco Upper Engine and Fuel Injector Cleaner, P/N 88861803, or an equivalent product.
      2. Remove the old TP sensor cover from the throttle body: grasp the cover, carefully lift it up and separate it from the throttle body.
      3. Tighten the throttle body fasteners to 89 lb in (= 10.1 N·m) (the text prints the metric value as "10 Y").
      4. Reprogram the ECM using the Service Programming System (SPS) with the latest calibration available on TIS2WEB.
      5. Perform the Throttle Learn Reset Procedure.

      Part numbers printed in the document

      The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

      Parts

      • Part number 19259452, Throttle Position (TP) Sensor Cover, quantity 1.

      Part numbers printed in the document

      The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

      Caution

      • Do not replace the throttle body; follow the procedure in the bulletin instead.
      • If the throttle body is dropped at any time during the procedure, abort the procedure and replace it with a new throttle body assembly.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：The Yukon entries are 2008-2011 GMC Canyon, Savana, Sierra, Sierra Denali and Yukon models (note: earlier Yukon model years are not listed).
    • Condition：The malfunction indicator lamp (MIL) is illuminated with a Reduced Engine Power message displayed.
    • Condition：A scan tool may show DTC P2135: Throttle Position (TP) Sensor 1-2 Correlation set as Current or in History.
    • Cause：The condition may be caused by the difference between TP Sensor 1 and TP Sensor 2 exceeding a calibrated value for more than 2 seconds.
    • Caution：Do not replace the throttle body; follow the procedure in the bulletin instead.
    • Repair：Clean the throttle body bore and throttle plate with a clean shop towel and GM Top Engine Cleaner, P/N 1052626 (in Canada, P/N 993026), or ACDelco Upper Engine and Fuel Injector Cleaner, P/N 88861803, or an equivalent product.
    • Repair：Remove the old TP sensor cover from the throttle body: grasp the cover, carefully lift it up and separate it from the throttle body.
    • Caution：If the throttle body is dropped at any time during the procedure, abort the procedure and replace it with a new throttle body assembly.
    • Confirm：After installing the new cover, if the scan tool TP Sensor 1 and 2 Agree/Disagree parameter displays Disagree, replace the throttle body assembly.
    • Confirm：If DTC P1516, P2101 and/or P2176 are set, replace the throttle body.
    • Repair：Tighten the throttle body fasteners to 89 lb in (= 10.1 N·m) (the text prints the metric value as "10 Y").
    • Repair：Reprogram the ECM using the Service Programming System (SPS) with the latest calibration available on TIS2WEB.
    • Repair：Perform the Throttle Learn Reset Procedure.
    • Parts：Part number 19259452, Throttle Position (TP) Sensor Cover, quantity 1.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This technical bulletin provides a procedure for replacing the throttle position sensor cover for concerns regarding a indicator lamp illuminated reduced power message displayed and DTC P2135 set.

  3. Manufacturer communication2005–2006 GMC YUKON DENALI ・ 2009-06-02

    Intermittent MIL/DTC P2138 with Reduced Engine Power

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

    Read the sentences of the record
    Remedy
    GENERAL MOTORS: INTERMITTENT MIL/SES/ DTC P2138 WITH REDUCED ENGINE POWER (REPAIR INSTRUMENT PANEL (IP) TO BODY HARNESS CONNECTOR). 2005-08 GM PASSENGERS CARS/LIGHT DUTY TRUCKS (INCL. SATURNS). *PE UPDATED 11/5/10. *PE UPDATED 4/4/11. *PE UPDATED 2/3/16. *PE

  4. Manufacturer communication2003–2006 GMC YUKON ・ 2004-10-04

    Service Engine Soon Light and Reduced Engine Power (P1516)

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      SERVICE ENGINE SOON LIGHT AND REDUCED ENGINE POWER WITH A DIAGNOSTIC TROUBLE CODE P1516. DIAGNOSTIC TROUBLE CODES P0120, P0220, P1514, P1515, P1518 AND P2135 MAY ALSO BE PRESENT. *TT

    Read the sentences of the record
    Remedy
    SERVICE ENGINE SOON LIGHT AND REDUCED ENGINE POWER WITH A DIAGNOSTIC TROUBLE CODE P1516. DIAGNOSTIC TROUBLE CODES P0120, P0220, P1514, P1515, P1518 AND P2135 MAY ALSO BE PRESENT. *TT

ELECTRONIC STABILITY CONTROL (ESC)2

  1. Owner complaint2003 GMC YUKON DENALI ・ 2018-03-21

    Reduced engine power light and speed drops to 20 MPH with check engine codes P0120 and P2135

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      Not stated

    Read the sentences of the record
    Outcome
    THE CONSUMER STATED THE VEHICLE WAS REPAIRED AND REQUESTED WITHDRAW THE COMPLAINT. *JS

  2. Owner complaint2006 GMC YUKON ・ 2017-11-07

    Sudden power loss and reduced engine power warning while driving on freeway

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

    Read the sentences of the record
    Fault
    MY VEHICLE WAS IN MOTION DRIVING ON THE FREEWAY AT 70 MPH (= 112.7 km/h) WHEN ALL OF THE SUDDEN MY CAR LOST POWER TO 30 MPH (= 48.3 km/h) ALL THE WAY DOWN TO 5 MPH (= 8.05 km/h).I PRESSED ON THE ACCELERATOR TRYING TO GAIN SPEED WITHOUT SUCCESS THE CAR DID NOT ACCELERATE MORE THAN 30 MPH (= 48.3 km/h), NO MATTER HOW MUCH I PRESSED ON THE ACCELERATOR. (1 more)
    Outcome
    THAT DID NOT WORK.

ENGINE AND ENGINE COOLING2

  1. Manufacturer communication2003 GMC YUKON ・ 2004-09-27

    Service Engine Soon light and reduced engine power mode

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      SERVICE ENGINE SOON LIGHT AND / OR REDUCED ENGINE POWER MODE DUE TO DIAGNOSTIC TROUBLE CODES P0120, P0220, P1516 AND/OR P1518. THIS CONDITION IS NORMALLY VERY INTERMITTENT. *TT

    Read the sentences of the record
    Remedy
    SERVICE ENGINE SOON LIGHT AND / OR REDUCED ENGINE POWER MODE DUE TO DIAGNOSTIC TROUBLE CODES P0120, P0220, P1516 AND/OR P1518. THIS CONDITION IS NORMALLY VERY INTERMITTENT. *TT

  2. Manufacturer communication2003 GMC YUKON ・ 2004-09-27

    SERVICE ENGINE SOON Light and Reduced Engine Power Mode

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      SERVICE ENGINE SOON LIGHT AND / OR REDUCED ENGINE POWER MODE DUE TO DIAGNOSTIC TROUBLE CODES P0120, P0220, P1516 AND/OR P1518. THIS CONDITION IS NORMALLY VERY INTERMITTENT. *TT

    Read the sentences of the record
    Remedy
    SERVICE ENGINE SOON LIGHT AND / OR REDUCED ENGINE POWER MODE DUE TO DIAGNOSTIC TROUBLE CODES P0120, P0220, P1516 AND/OR P1518. THIS CONDITION IS NORMALLY VERY INTERMITTENT. *TT

ENGINE1

  1. Owner complaint2003 GMC YUKON DENALI ・ 2013-12-30

    Traction control and reduced engine power warning lights; vehicle stalled

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3CorrectionNot repaired

      THE VEHICLE WAS NOT REPAIRED.

    Read the sentences of the record
    Fault
    THE CONTACT STATED THAT THE TRACTION CONTROL AND THE REDUCED ENGINE POWER WARNING LIGHTS ILLUMINATED AND CAUSED THE VEHICLE STALLED.
    Remedy
    THE VEHICLE WAS NOT REPAIRED.
    Inspection
    THE VEHICLE WAS TAKEN TO THE DEALER, WHO WAS UNABLE TO DIAGNOSE THE FAILURE.

VEHICLE SPEED CONTROL1

  1. Owner complaint2003 GMC YUKON ・ 2003-03-13

    Check engine light displayed, engine enters reduced power mode

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

    Read the sentences of the record
    Fault
    WHILE DRIVING OR IDLING, THE "CHECK ENGINE LIGHT" IS DISPLAYED. (1 more)
    Remedy
    DEALER REPLACED ACCELERATOR CONTROL MODULE.
    Outcome
    THIS DID NOT CORRECT THE PROBLEM.

Showing 12 of the 14 you can open. Narrow the search to see the rest.