Skip to content
FaultCrate
日本語

This is an open preview: every record can be read without an account.

GMC Yukon 2000–2006

GMC YukonModel years 2000–2006

Change vehicle →
Clear the search
1 conditions added

Common on this vehicle:Corrosion or rust

remedyWheel Speed Sensor Mounting SurfaceRemove

Record by record

1 records state a cause or a remedy. Each record is shown as short labels in the order fault → finding the cause → correction. Press a label to narrow to the records that state it.

Read the records one by one (1)

Known issuesUnwanted ABS activation at low speed (front wheel speed sensor mounting corrosion)1

  1. Recall2000 GMC YUKON ・ —

    ABS activation recall in pickup trucks and SUVs

    1. 1Fault

      • Corrosion may occur between the front hub/bearing assembly and the wheel speed sensor; if the brakes are applied at a speed greater than 6 km/h (3.7 mph) but less than 16 km/h (10 mph), the corrosion may cause an unwanted ABS activation.
      • If this occurred where stopping distance is limited, a crash could occur.
      • The condition does not set any ABS codes and does not illuminate the ABS warning lamp.

    2. 2Finding the cause

      Steps to confirm (in the document’s order)

      1. Check the mounting surface on the sensor head for flatness against a metal machinist's scale or other straight edge, in multiple positions/directions (minimum 3).
      2. With the bearing rotated at about one revolution per second, the reading should be at least 350 ACmV; if it is less than 350 ACmV the wheel speed sensor must be replaced.

    3. 3Correction

      Repair

      1. If the mounting surface on the sensor is warped or bent, the sensor must be replaced.
      2. Thoroughly clean the wheel speed sensor mounting surface on the bearing hub with a wire brush, sandpaper, emery cloth, scotch brite or equivalent to remove any rust or corrosion.
      3. Spray two thin coats of the specified rust penetrating lubricant (corrosion inhibitor) on the complete sensor mounting surface on the bearing hub, letting it dry between coats.
      4. When the corrosion inhibitor is dry to the touch (about 10 minutes), apply a light coating of the specified grease to the complete sensor mounting surface on the bearing hub and to the sensor and O-ring.
      5. Tighten the wheel speed sensor mounting bolt to 18 N·m (13 lb ft).
      1 more points

      Parts

      • Parts listed: 89022217 Lubricant, Rust Penetrating, and 01051344 Lubricant, Wheel Bearing.

      Part numbers printed in the document

      The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

      Caution

      • Remove the sensor by pulling it straight out of the bore; do not pry it with a screwdriver or other device, because prying will break the sensor body off in the bore.
      • This revision changes some breakpoints and adds vehicles that have moved into the severe corrosion areas; copies of bulletin 05068B, issued April 2006, are to be discarded.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to certain 1999-2002 Chevrolet Silverado and GMC Sierra, 2000-2002 Chevrolet Tahoe, Suburban and GMC Yukon, Yukon XL, and 2002 Chevrolet Avalanche that have at any time been registered in the listed areas.
    • Applies to：The revised defect notice adds Delaware, Iowa, Maryland, Minnesota, Missouri, Wisconsin and the District of Columbia to the original states of Connecticut, Illinois, Indiana, Maine, Massachusetts, Michigan, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont and West Virginia.
    • Condition：Corrosion may occur between the front hub/bearing assembly and the wheel speed sensor; if the brakes are applied at a speed greater than 6 km/h (3.7 mph) but less than 16 km/h (10 mph), the corrosion may cause an unwanted ABS activation.
    • Condition：If this occurred where stopping distance is limited, a crash could occur.
    • Condition：The condition does not set any ABS codes and does not illuminate the ABS warning lamp.
    • Caution：Remove the sensor by pulling it straight out of the bore; do not pry it with a screwdriver or other device, because prying will break the sensor body off in the bore.
    • Confirm：Check the mounting surface on the sensor head for flatness against a metal machinist's scale or other straight edge, in multiple positions/directions (minimum 3).
    • Repair：If the mounting surface on the sensor is warped or bent, the sensor must be replaced.
    • Repair：Thoroughly clean the wheel speed sensor mounting surface on the bearing hub with a wire brush, sandpaper, emery cloth, scotch brite or equivalent to remove any rust or corrosion.
    • Repair：Spray two thin coats of the specified rust penetrating lubricant (corrosion inhibitor) on the complete sensor mounting surface on the bearing hub, letting it dry between coats.
    • Repair：When the corrosion inhibitor is dry to the touch (about 10 minutes), apply a light coating of the specified grease to the complete sensor mounting surface on the bearing hub and to the sensor and O-ring.
    • Repair：Tighten the wheel speed sensor mounting bolt to 18 N·m (13 lb ft).
    • Confirm：With the bearing rotated at about one revolution per second, the reading should be at least 350 ACmV; if it is less than 350 ACmV the wheel speed sensor must be replaced.
    • Repair：Tighten the brake caliper mounting bracket bolts to 175 N·m (129 lb ft) on 1500 Series vehicles and 300 N·m (221 lb ft) on 2500 Series vehicles.
    • Parts：Parts listed: 89022217 Lubricant, Rust Penetrating, and 01051344 Lubricant, Wheel Bearing.
    • Caution：This revision changes some breakpoints and adds vehicles that have moved into the severe corrosion areas; copies of bulletin 05068B, issued April 2006, are to be discarded.
    Cause
    CERTAIN PICKUP TRUCKS AND SPORT UTILITY VEHICLES MAY EXPERIENCE UNWANTED ANTILOCK BRAKE SYSTEM (ABS) ACTIVATION. THIS CONDITION IS MORE LIKELY TO OCCUR IN ENVIRONMENTALLY CORROSIVE AREAS. THIS RECALL WILL BE LAUNCHED IN THE "SALT BELT" STATES OF CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, MARYLAND, MASSACHUSETTS, MAINE, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, WISCONSIN AND THE DISTRICT OF COLUMBIA ONLY.
    Remedy
    DEALERS ARE TO REMOVE THE WHEEL SPEED SENSOR AND THOROUGHLY CLEAN THE WHEEL SPEED SENSOR MOUNTING SURFACE ON THE BEARING, APPLY RUST INHIBITOR TO THE CLEANED SURFACE, GREASE THE MOUNTING SURFACE, REINSTALL THE WHEEL SPEED SENSOR, AND CHECK THE PEAK-TO-PEAK OUTPUT VOLTAGE TO ENSURE THE WHEEL SPEED SIGNAL IS WITHIN SPECIFICATIONS. THE RECALL BEGAN SEPTEMBER 22, 2005. OWNERS MAY CONTACT CHEVROLET AT 1-800-630-2438 OR GMC AT 1-866-996-9463.
    Consequence
    THIS CAN CAUSE INCREASED STOPPING DISTANCES DURING LOW-SPEED BRAKE APPLICATIONS, WHICH COULD RESULT IN A CRASH.