Skip to content
FaultCrate
日本語

This is an open preview: every record can be read without an account.

GMC Yukon 2000–2006

GMC YukonModel years 2000–2006

Change vehicle →
Clear the search
1 conditions added

Common on this vehicle:

issueRecords under no cardRemove

Record by record

3 records state a cause or a remedy. Each record is shown as short labels in the order fault → finding the cause → correction. Press a label to narrow to the records that state it.

Component named as the cause

Work done

A ribbon is as wide as the records that state both of its ends (only the commonest are drawn). A record that names several symptoms or components runs through each. Orange is records that say the fault came back or was not fixed. Results come from owners’ reports only; one that does not say is “result not stated”. None of this is a likelihood of a cause or a rate at which work succeeds.

Read the records one by one (1)

ELECTRICAL SYSTEM1

  1. Manufacturer communication2006 GMC YUKON ・ 2024-05-06(2 earlier editions of this document folded here)

    Magnetically Controlled Suspension Electrical Connector Not Seated

    1. 1Fault

      • The subject names a Service Suspension System message with DTCs C0575, C0580, C0585 or C0590.
      • Some customers may comment on a Service Suspension System message displayed on the Drivers Information Center (DIC).

    2. 2Finding the cause

      Possible causes

      • During assembly, the 90 degree electrical connector at the top end of a shock absorber (actuator) may not have been fully seated, or may have been bumped firmly enough to partially disconnect it or create an internal contact concern.

      Steps to confirm (in the document’s order)

      1. Visually examine the green insulator and center post of the electrical connector to make sure it is straight and in serviceable condition; replace the connector and retest if required.
      2. Reconnect the electrical connector to the shock absorber (actuator), clear the suspension DTC and confirm that the code does not reset.
      3. If the code returns, remove the electrical connector from the shock absorber (actuator) and pigtail, and swap it with the connector on the opposite side shock absorber (actuator).

    3. 3Correction

      Repair

      • If the DTC follows the connector to the other side, replace the connector; if not, refer to SI and follow the diagnostics for the DTC originally found.

      Parts

      • Part number 19180262, Connector, S/ABS Elec Susp Control.

      Part numbers printed in the document

      The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

      Caution

      • Complete the document's steps before attempting shock absorber (actuator) replacement.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：The model list includes the 2006-2014 GMC Yukon and Yukon XL.
    • Applies to：It applies to vehicles equipped with RPO F55, Z55 or Z95.
    • Condition：The subject names a Service Suspension System message with DTCs C0575, C0580, C0585 or C0590.
    • Condition：Some customers may comment on a Service Suspension System message displayed on the Drivers Information Center (DIC).
    • Cause：During assembly, the 90 degree electrical connector at the top end of a shock absorber (actuator) may not have been fully seated, or may have been bumped firmly enough to partially disconnect it or create an internal contact concern.
    • Caution：Complete the document's steps before attempting shock absorber (actuator) replacement.
    • Confirm：Visually examine the green insulator and center post of the electrical connector to make sure it is straight and in serviceable condition; replace the connector and retest if required.
    • Confirm：Reconnect the electrical connector to the shock absorber (actuator), clear the suspension DTC and confirm that the code does not reset.
    • Confirm：If the code returns, remove the electrical connector from the shock absorber (actuator) and pigtail, and swap it with the connector on the opposite side shock absorber (actuator).
    • Repair：If the DTC follows the connector to the other side, replace the connector; if not, refer to SI and follow the diagnostics for the DTC originally found.
    • Parts：Part number 19180262, Connector, S/ABS Elec Susp Control.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    Magnetically Controlled Suspension Electrical Connector Not Seated.

Showing 1 of the 3 you can open. Narrow the search to see the rest.